- clutch actuator fitting (1 replies)
- driveshaft length, ls-1 t-56 to 2 pc rear main block (7 replies)
- Going from auto - manual (t56 style) (14 replies)
- Blame it on the cold? Transmission Problems (10 replies)
- New Headers? (6 replies)
- T56 out of a GTO (0 replies)
- New shifter from McLeod.. T56 (15 replies)
- New Project setup questions (7 replies)
- Help/ideas how to use C5 rearend with driveshaft (5 replies)
- trans (5 replies)
- aluminum drive shafts???? (2 replies)
- Push button shifter ? (8 replies)
- installed new 700r4 (1 replies)
- DSE T-56 crossmember-not sale any more? (3 replies)
- 4 speed manual transmission Help (0 replies)
- 4l80e Crossmember Conversion? (1 replies)
- 351w Tremec 3550 clutch question (2 replies)
- T56 clutch booster / pedal travel ???? (3 replies)
- Richmond 5 speed Question... (2 replies)
- Opinions on the Detroit True Trac (5 replies)
- Looking for a really good rear end for my car 12 bolt (7 replies)
- RPM calculator - what percent slip from lock-up converter? (6 replies)
- TKO 600 vs T56? (12 replies)
- Gear Vendors Overdrive? (8 replies)
- TH700 conversion (6 replies)
- Muncie 764 Tail Extension (0 replies)
- mcleod twin disc? (24 replies)
- Blown Small Block (2 replies)
- Intresting Mopar(?) irs installation-any info? (3 replies)
- T56 bellhousing clarifcation?? (3 replies)
- Gear Vendor for the Glide? (6 replies)
- The RPM Formula! (6 replies)
- Muncie 4 Speed worth?? (4 replies)
- spool (0 replies)
- 4L80E In A 67? (9 replies)
- How much power could this combo hold up to? (2 replies)
- Which B & M Shifter? (14 replies)
- Any T56 Rebuilders Out There? (4 replies)
- Help me decide (T56 bellhousing) (10 replies)
- Manual or Auto? (91 replies)
- strong/light weight tranny (1 replies)
- Transmission help needed ! (1 replies)
- Sequential Gearboxes. (33 replies)
- JL8 12 bolt verification (2 replies)
- Trans speedo gear?! (1 replies)
- Using OEM '69 Chevelle speedo w/ 4L60??? (3 replies)
- high horse power overdrive transmissions (37 replies)
- 9" front seal replacement???? (7 replies)
- Can I use an LS1 4L60E on an LT1? (1 replies)
- What rear end specs do i need for my DSE tubbed 69? (3 replies)
- Can i use this to mock install my T-56?? (0 replies)
- Cable-X calibration question: T56 "gear" teeth? (2 replies)
- Universal Shrifter: Ford, Mopar, Etc. (2 replies)
- Center Force Dual Friction Clutch (1 replies)
- Help vibrations (12 replies)
- 10 bolt housing code? (3 replies)
- Budget rear disk with a 9"...? (6 replies)
- more pinion angle fun (9 replies)
- TKO vs T56 (3 replies)
- BigStuff3/Paddle Shifter Compatibility (0 replies)
- pinion angle question (5 replies)
- Need help choosing gear ratio (10 replies)
- jag rear question (5 replies)
- Blew my 9".... (5 replies)
- TKO 600 question (15 replies)
- Stock Camaro Rear End (6 replies)
- G-Machine question..... (39 replies)
- LT1/T56 clutch & flywheel? (2 replies)
- Need help with 4L80E (4 replies)
- Torque setting on dual mass flywheel for LT1 (3 replies)
- Trying to install thrust washers.... (1 replies)
- Clutch problems (4 replies)
- I need a good calculator (3 replies)
- Please help me clear my head on what is needed for a SBC T56 Swap. (15 replies)
- Mocking up a T-56 (2 replies)
- What is "Manumatic" Technology (20 replies)
- Looking to put in a 6speed (4 replies)
- U-joint question (3 replies)
- What rear are you guys running on your 69 Camaro? (6 replies)
- T56 to Hemi (5 replies)
- TKO 600 vs T56 (13 replies)
- SMG trans (6 replies)
- Att:Shay Cambell (9 replies)
- 10blt. 8.2" posi question (14 replies)
- C-Clip eliminators (20 replies)
- Centerforce Dual Friction Clutch (13 replies)
- Electronic Tranny and speedometer.. (2 replies)
- Crossmember for ZF 6 speed (10 replies)