5 Years Later - It's Not a "new" Project, And Not a New Member Anymore!!!

[syborg tt]

Okay parts update.
The Mallory Crank Trigger for the project came in today.
Thanks to Mike Lee at Race Proven Motors for the support.
www.raceprovenmotors.com

http://www.syborgtwinturbo.com/albums/Build/2007_01_17_001.jpg

Temporary Curtain to keep the heat in the back half of the garage.
Wait till you see the permanent curtain.

http://www.syborgtwinturbo.com/albums/Build/2007_01_20_001.jpg

It's all organized and ready to work.

http://www.syborgtwinturbo.com/albums/Build/2007_01_20_004.jpg

So in the end.
16 - 2 x 8 x 20 foot boards
21 - 2 x 6 x 8 foot boards
10 - 4 x 8 x 1/2" sheets of plywood
3 - 8.6' x 11.6' Tarps
1 - Attic Ladder
1 - Fluorescent Light
4800 Staples (arm really hurts)
One Hammer Stapler
6 Rolls of R-13 Insulation
5 Rolls of R-19 Insulation
146 Pro Vents for the Vaulted Ceiling (not foreseen in the budget)
2 - Craftsman Rolling tool chests (also not in the budget)

It's complete and I'm to tired to work on the truck.
Did I also mention my wife never complained once during this project and all the hours I spent working in my garage.

[black2002ls]

It's complete and I'm to tired to work on the truck.
Did I also mention my wife never complained once during this project and all the hours I spent working in my garage.


The most amazing statement in the update :D

Nice work on the carpentry there Marty!

[syborg tt]

Good Morning All,

Things are Finally falling into place.

The Guy's the Crew @ Rockford Racecraft have starting working on the motor.
It's ready to be assembled.

Quick Picture of the Pistons from JE ( 4.125 bore )


http://www.syborgtwinturbo.com/albums/Build/2007_01_24_1_Twouncoated.jpg

After Coating and before Coating.

The piston coating is a "cermet thermal barrier coating" designed for high temperature/pressure applications and is especially suited for piston domes in forced inducted and nitrous motor applications.

http://www.syborgtwinturbo.com/albums/Build/2007_01_24_2_coatedvuncoated.jpg

Close up of the Coated Pistons

http://www.syborgtwinturbo.com/albums/Build/2007_01_24_4_Coatedclose.jpg

Prepping the Bearings for Coating.

http://www.syborgtwinturbo.com/albums/Build/2007_01_24_5_preppedmains.jpg

http://www.syborgtwinturbo.com/albums/Build/2007_01_24_6_Preppedrodbearings.jpg

[syborg tt]

The bearing coating is a dry film lubricant coating applied at micron thickness and used to prevent scuffing, galling, and reducing reciprocating friction.

http://www.syborgtwinturbo.com/albums/Build/2007_01_24_7_allcoated.jpg

Close up of the Coated Bearings - Looks Pretty

http://www.syborgtwinturbo.com/albums/Build/2007_01_24_8_Beforeandaftercomparison.jpg

This work is done in house and turn around is very quick.

http://www.syborgtwinturbo.com/albums/Renderings/RR_Logo.jpg

www.rockfordracecraft.com

[black2002ls]

Its coming together!

[syborg tt]

Good Morning All,

Guy and Crew at Rockford Racecraft are getting ready to inspect the block for external flaws.

http://www.syborgtwinturbo.com/albums/Build/2007_01_25_2.jpg

They found some flaws that would have to be taken care of before it could be painted.
See the Left Hand side of the block.

http://www.syborgtwinturbo.com/albums/Build/2007_01_25_4_Fix.jpg

Just a close up view.

http://www.syborgtwinturbo.com/albums/Build/2007_01_25_5_Fix.jpg


Needed to get the temporary hardware organized. We plan to install all new hardware on the truck.
We will keep you posted as to whom we choose.

http://www.syborgtwinturbo.com/albums/Build/2007_01_28_001.jpg

Had to put the motor together so I can work on the Turbo support brackets.

http://www.syborgtwinturbo.com/albums/Build/2007_01_28_004.jpg

[syborg tt]

Added a couple more shelves to the rack for parts.

http://www.syborgtwinturbo.com/albums/Build/2007_01_28_005.jpg

More to come next week.

[Sales@Dutchboys]

MAN! I cant wait till that truck is done, That thing is BAD!

[black2002ls]

slowly but surely!

[syborg tt]

Good Morning All,

Sorry work has really been kicking my butt the last two weeks.
Still working on the truck instead of sleeping.

Guy cleaned up the burs and casting flaws on the block.

http://www.syborgtwinturbo.com/albums/Build/2007_01_29_0.jpg

The front of the block was pretty nasty. Looks very good now.
Can't wait to paint the block.

http://www.syborgtwinturbo.com/albums/Build/2007_01_29_1.jpg

Put all the cladding back on the truck. Getting it ready for final Fit.
Only one piece of cladding left to make in Fiberglass.
So I headed off to VFN Fiberglass.

http://www.syborgtwinturbo.com/albums/Build/2007_01_30_004.jpg

Dennis over at Hi Speed Welding Remade the Grille insert in Steel.
www.highspeedwelding.com

http://www.syborgtwinturbo.com/albums/Build/2007_01_30_007.jpg

[syborg tt]

Guy getting the rings Ready.

http://www.syborgtwinturbo.com/albums/Build/2007_02_01_0.jpg

Testing them in the Block.

http://www.syborgtwinturbo.com/albums/Build/2007_02_01_1.jpg

Rods & Pistons ready to install in the block.

http://www.syborgtwinturbo.com/albums/Build/2007_02_01_2.jpg

The Long Block should be Assembled in the next week or two.

[syborg tt]

Good Morning All,



The truck is in Limbo right now.
I need to buy an enclosed trailer so I've spent all of my spare time looking for one.

http://www.syborgtwinturbo.com/albums/Build/2007_02_05_006.jpg

In the meantime the Guy's at Rockford Racecraft have assembled the short block.
All the parts getting ready for there new home.

http://www.syborgtwinturbo.com/albums/Build/2007_02_07_0.jpg

The infamous v6 Billet Crank.
For you v8 guy's these only take 6 to 9 months to get and cost a small fortune.
$3000.00

http://www.syborgtwinturbo.com/albums/Build/2007_02_07_2.jpg

The Bowtie Block came from GM with ARP Studs.
Saves a little money there but then again the block wasn't cheap either.

http://www.syborgtwinturbo.com/albums/Build/2007_02_07_11.jpg

The Crank Resting in it's new home.

http://www.syborgtwinturbo.com/albums/Build/2007_02_07_12.jpg

Wait, I don't have any pics of the pistons in the hole.

[black2002ls]

lookin' good marty

[Nate Hanson]

Hi Marty!

[syborg tt]

Hi Marty!

welcome aboard

[Nate Hanson]

welcome aboard
Of course, glad to be here. Now you can introduce me to some guys that will steer in the right direction as far as some modifications and suggestions.

[syborg tt]

Good Morning All,

Meet with the Interior guy last week and we are going to start working on the interior while I am waiting to go to paint.
Plans are to Haul the cab over to them early next week now that I have an Enclosed Trailer.


As promised pictures of the pistons & rods in the short block.

http://www.syborgtwinturbo.com/albums/Build/2007_02_13_3.jpg

Dan at DLS set us up with the Cam Specs

http://www.syborgtwinturbo.com/albums/Build/2007_02_14_2.jpg

Comp Cam built the Camshaft for us.

http://www.syborgtwinturbo.com/albums/Build/2007_02_14_3.jpg

Cloyes Hex-A-Just Timing Chain Set

http://www.syborgtwinturbo.com/albums/Build/2007_02_14_5.jpg

Cam is in the hole (in my best Bill Murray from Caddy Shack voice)

http://www.syborgtwinturbo.com/albums/Build/2007_02_14_9.jpg

More cool tools that I can't afford.

[syborg tt]

http://www.syborgtwinturbo.com/albums/Build/2007_02_14_11.jpg

http://www.syborgtwinturbo.com/albums/Build/2007_02_14_13.jpg

Okay, I've finally bought a trailer from American Trailers 304.776.1680 (ask for Charlie)
20 Foot Haulmark Thrifty for $5230.00 and $167.00 for Delivery ($1.25 mile)
Couldn't be happier.

http://www.syborgtwinturbo.com/albums/Build/2007_02_16_027.jpg

http://www.syborgtwinturbo.com/albums/Build/2007_02_16_030.jpg

Taking the truck back apart this weekend and bringing the chassis over to the Fab shop
so they can make me a chassis dolly

[TEDDYS CAMARO]

EVERYTHINGS LOOKING GOOD.:thumbsup:

[syborg tt]

Good Evening All,

This has been a very long week and a very sad Week.
http://www.syty.net/forums/showthread.php?t=46822
We lost a great guy in the SyTy Community and he will be Dearly missed.

One of his last post over on syty.net was in my build thread. Dave asked if I would adopt him.
The answer is yes but I think you a little to old to be my son and no you can't drive my truck.
So you are going to have to sit in the passenger seat.

The seat is yours Dave - gonna miss you big guy.

Okay I will try to go to back to the updates.

The New Head Gaskets arrived

http://www.syborgtwinturbo.com/albums/Build/2007_02_20_0.jpg

Getting ready to rip the truck apart again.

http://www.syborgtwinturbo.com/albums/Build/2007_02_24_002.jpg

Don't try this at home alone -- not a good idea.
Really I am going to buy a lift for my garage.

Wait I have an idea anyone want to sponsor me.

http://www.syborgtwinturbo.com/albums/Build/2007_02_24_005.jpg

The Bed off and on it's body work stand.
Looks like I am going to need to contact Caleb and ask him if he set it up for 7 foot tall body men. :dunno:

http://www.syborgtwinturbo.com/albums/Build/2007_02_24_006.jpg

Chassis sitting naked.
Actually I started doing a hardware inventory and it's time to get some new nut's and bolts.

http://www.syborgtwinturbo.com/albums/Build/2007_02_24_008.jpg

[syborg tt]

Decided to take a few Pics of the chassis while it was apart again.

http://www.syborgtwinturbo.com/albums/Build/2007_02_24_009.jpg

Just another angle of the rear back half

http://www.syborgtwinturbo.com/albums/Build/2007_02_24_014.jpg

http://www.syborgtwinturbo.com/albums/Build/2007_02_24_016.jpg

Tom stopped by on Sunday to help me put the motor back in the truck.
Yep -- missing more bolts time to call Billet Specialties.

http://www.syborgtwinturbo.com/albums/Build/2007_02_25_001.jpg

Fuel cell located back between the rails.
Yep missing some more bolts.

http://www.syborgtwinturbo.com/albums/Build/2007_02_25_004.jpg

This has been the hardest post that I have ever done.
Farwell Dave we are all going to miss you.

[awr68]

Damn Marty!! Everything is looking great...it's been awhile since I checked this thread...great job and nice trailer too!!!

[syborg tt]

Damn Marty!! Everything is looking great...it's been awhile since I checked this thread...great job and nice trailer too!!!

thank you very much - it sure has been fun

[black2002ls]

looking good. That shot of the frame from the side is WICKED
:thumbsup:

[Garage Dog 65]

Looking great Bro ! Been a long trip - but when you fire up that awesome motor it will all be paid back in full. :thumbsup:

Can't wait !!!

[syborg tt]

Looking great Bro ! Been a long trip - but when you fire up that awesome motor it will all be paid back in full. :thumbsup:

Can't wait !!!

I can't wait either. My luck is it will be complete at the end of summer and i'll have to park it for the winter.

[turbozilla907]

Is this truck AWD or rear wheel drive ?????

Looks awsome ,, I saw some pics at SY TY ..

[syborg tt]

Is this truck AWD or rear wheel drive ?????

Looks awsome ,, I saw some pics at SY TY ..

this is the sonoma gt which came from the factory in 2wd form only

[deuce_454]

that side shot looks like somthing destined for a hot wheels look alike :thumbsup:

it's really nearing completion..

[syborg tt]

that side shot looks like somthing destined for a hot wheels look alike :thumbsup:

it's really nearing completion..

Not to worry i am working on it with Johnny Lighting. My dad is friends with the gentleman that started the Company

[syborg tt]

Good Evening All,

What a weekend. Stopped by Rad Rides on Saturday to see the progress on the car there building
to compete for the Riddler Award. Wow is all I can say I promise I will post pics next week.

Okay back to the update.
Mocked up the interior to see what it would look like.
My Goal is to make it look like a Factory Prototype

http://www.syborgtwinturbo.com/albums/Build/2007_03_03_002.jpg

The Factory Seats have been recovered in Leather & Suede.

Billet Door Sills - I Also have Billet Sill Plates to protect the paint.
Working on an Idea for the Side Bar.

http://www.syborgtwinturbo.com/albums/Build/2007_03_04_007.jpg

Quick Shot of the Dash.
The Dash will be leaving tomorrow morning to get body worked and painted.

http://www.syborgtwinturbo.com/albums/Build/2007_03_04_008.jpg

Ordered some parts from Lokar to compliment the Interior

Door Handles - I was going to go black but i need to get an accent color in the door panel

http://www.syborgtwinturbo.com/albums/Build/2007_03_08_002.jpg

Cable releases for the door latch.

http://www.syborgtwinturbo.com/albums/Build/2007_03_08_001.jpg

[syborg tt]

Inside door handle pulls.

http://www.syborgtwinturbo.com/albums/Build/2007_03_08_003.jpg

Billet "Black" Gas Pedal. It compliments the Wilwood brake pedal nicely.

http://www.syborgtwinturbo.com/albums/Build/2007_03_08_005.jpg

I want to thank Eric at Lokar for helping me out.

That's all - Have a great weekend.

[black2002ls]

that interior is fabulous!!!

[G-Body]

By far my favorate build on here to follow, I can only imagine how fast that bank account is dewendling, Man im jealous lol

[syborg tt]

By far my favorate build on here to follow, I can only imagine how fast that bank account is dewendling, Man im jealous lol

Thank you very much

[deuce_454]

everything about this build is just tastefull.. love the attention to detail, but also that everything is just a little understated, and a little better than it seems at first glance.. love it, and love the concept of keeping it "factory" prototype...
:thumbsup:

[syborg tt]

everything about this build is just tastefull.. love the attention to detail, but also that everything is just a little understated, and a little better than it seems at first glance.. love it, and love the concept of keeping it "factory" prototype...
:thumbsup:

It's been very hard trying to stay true to the original rendering. But at least it give's me a goal or a vision to work towards.

Thanks again.

[TEDDYS CAMARO]

Looks good. I went to autorama....nice!!

[syborg tt]

Good Morning All,

The truck is going back together yet again and waiting to get loaded in the trailer to head over to the body shop.
Put the Cab back on Saturday Afternoon in between errands and go-cart racing.

http://www.syborgtwinturbo.com/albums/Build/2007_03_17_001.jpg

Working on the new Dash Layout.
Looks like I may change the Gauge color and go silver background instead.

http://www.syborgtwinturbo.com/albums/Build/2007_03_07_010.jpg

Tom was kind enough to send me all my material to match my seats.

http://www.syborgtwinturbo.com/albums/Build/2007_03_18_044.jpg

That is what's left of 2 really big Cow's

http://www.syborgtwinturbo.com/albums/Build/2007_03_18_046.jpg

[syborg tt]

The Guy's over at Body Language smoothed the Dash and put a coat of paint on it to protect it.
[email protected]

http://www.syborgtwinturbo.com/albums/Build/2007_03_20_001.jpg

http://www.syborgtwinturbo.com/albums/Build/2007_03_20_003.jpg

Ordered the new headliner from LMC Truck.
The new headliners has an ABS backing instead of the flimsy foam backing.

http://www.syborgtwinturbo.com/albums/Build/2007_03_20_004.jpg


More to come in the next couple weeks

[black2002ls]

looking good Marty! I've been itching for an update on this

[syborg tt]

Good Morning All,

Ron Wilson & I have been toying around with the Idea of a custom set of Skuff plates for hood pins.
Ron drew up the design with some direction from me.

Then Mike Renz Introduced me to the Guy's at Fabritek
Right out of the Gate these guy's said they would love to work with us.
Fabritek Co. Inc. Your one stop machine and fabrication shop. (http://www.fabritek.com)

Here is the design we came up with -- tell me what you think.

http://www.syborgtwinturbo.com/albums/Build/2007_03_22_2.jpg

Close up of the Skuff plate

http://www.syborgtwinturbo.com/albums/Build/2007_03_28_002.jpg

Good thing my other GT is still in my warehouse

http://www.syborgtwinturbo.com/albums/Build/2007_03_28_003.jpg

With the Pin and lock in place

http://www.syborgtwinturbo.com/albums/Build/2007_03_28_005.jpg

Side View

http://www.syborgtwinturbo.com/albums/Build/2007_03_28_006.jpg

Please tell me what you think.

[ironworks]

They would look really nice for manly ear wear, for sure. J/K

those things are cool

[syborg tt]

They would look really nice for manly ear wear, for sure. J/K those things are cool

I can just see it now - someone ear stretch around a pair of these things

[awr68]

Looks good! Ah to have the tallent and equipment to build that stuff!!

[black2002ls]

they look great Marty. And a true testament to the lengths you are going to on this project

[syborg tt]

Looks good! Ah to have the tallent and equipment to build that stuff!!


i do my best to surround myself with really good people

[formula98]

Thanks Marty, My thoughts are that it is always great to have people to brain storm with and come up with great ideas. They came out great!

Ron

[syborg tt]

Thanks Marty, My thoughts are that it is always great to have people to brain storm with and come up with great ideas. They came out great!

Ron

Yep it was great working with you. It sure did save a bunch of money having you do all design work. You should tell people that's what you do and maybe they will take advantage of your talents and then use Fabritek to make the parts.

I would say it's a great marriage.

ps - check is in the mail for the design files.

[novanutcase]

Those things are sweet! Nice job!!:thumbsup:

John

[syborg tt]

Good Morning,

It's gonna be a good month.
Popular Hot Rodding just did a nice little feature on the truck in June issue.

http://www.syborgtwinturbo.com/albums/stjan07/2007_June_PHR_00_640.jpg

Every Day it's getting a little closer to being complete.

http://www.syborgtwinturbo.com/albums/stjan07/2007_June_PHR_01_640.sized.jpg

Prior to the Article being published the truck was going to be painted at Rad Ride's.
However, due to schedule's and deadline conflict the truck is now being
painted at Kenny Davis Hot Rods.
www.kdhotrods.com

Did I say Thank you Steve - ps your hood pin will be ready to ship tommorow

[TravisB]

I just want everyone that checks this thread to know.....Martys truck is completely badass....it far exceeded my expectations of what I thought it was going to look like. Fab work is second to none everywhere on the truck.:thumbsup:

[syborg tt]

I just want everyone that checks this thread to know.....Martys truck is completely badass....it far exceeded my expectations of what I thought it was going to look like. Fab work is second to none everywhere on the truck.:thumbsup:

Thanks Travis.

I am glad you guy's have the truck and i get to spend some time with my kids this summer.

ps did i mention i'll see ya on the 11 of may. Looks like i'm coming out for the weekend to work on the truck.

[TravisB]

Thanks Travis.

I am glad you guy's have the truck and i get to spend some time with my kids this summer.

ps did i mention i'll see ya on the 11 of may. Looks like i'm coming out for the weekend to work on the truck.


So I hear....thats right around the corner. I bet your wife will be happy, Arkansas is to far away for you to drop by the shop everyday and take pictures of progress which=more time at home for you....haha

BTW you have been getting lots of ink lately.....

[novanutcase]

Congrats!! My only question is why this wasn't published earlier!!! BADASS to say the least!!:thumbsup:

John

[black2002ls]

I check the in progress forum every day hoping for an update. Glad to see this thing being featured. It truely deserves the press!!!

[ironworks]

Is Johns nova in there in the under construction section?

Congrats on the truck article.

Rodger

[68protouring454]

rodger yes the nova is in there looks good.


oh ya, unlike what martys article says, the syborg is being painted at KD hotrods, not radrides.

[Garage Dog 65]

I'll echo the 'much deserved press' comment Marty ! Very nice work and I just can't wait to hear that motor running ! Congrats !!! :thumbsup:

[Payton King]

one of the most bad ass trucks that I have ever seen.

I hear those Arkansas boys do really good work. If I ever get back up to NW Ar I need to stop in.

[kennyd]

one of the most bad ass trucks that I have ever seen.

I hear those Arkansas boys do really good work. If I ever get back up to NW Ar I need to stop in.


your welcome here anytime .

[syborg tt]

So I hear....thats right around the corner. I bet your wife will be happy, Arkansas is to far away for you to drop by the shop everyday and take pictures of progress which=more time at home for you....haha

BTW you have been getting lots of ink lately.....


Trust me i'll be there more then you want me to.

[syborg tt]

your welcome here anytime .

what about me - any chance i can stop by

[Sales@Dutchboys]

:thumbsup: Congrats.....Most of the time I dont like newer things...BUT! this thing has soooo much cool stuff going on!

[kennyd]

what about me - any chance i can stop by

by appointment only !

[syborg tt]

by appointment only !

bummer - i figured i would just stop by and hang out for a few day's

[syborg tt]

Good Afternoon all,

Okay it's time to let the Cat out of the Bag officially.
Last Friday Night we packed up the trailer and headed to Nebraska.

http://www.syborgtwinturbo.com/albums/Build/2007_04_13_004.jpg

I wish you could see the front of the trailer -- it's packed with parts.

http://www.syborgtwinturbo.com/albums/Build/2007_04_13_005.jpg

So you ask what's in Nebraska? The "Recovery Room" is in Nebraska.
This truck isn't ready for Interior is it. Nope !!

My father and I figured we might as well kill two birds with one Stone.
Kenny was dropping off the 57 at Tracy's - so we figured we should just meet at Tracy's.

http://www.syborgtwinturbo.com/albums/Build/kd_log.jpg

I'm pretty excited to be working with Kenny Davis Klan.
They are great group of guy's and so far we are having a blast picking on Kenny.

http://www.syborgtwinturbo.com/albums/Build/2007_04_16_004.jpg

Plenty more to come in the near Future.
So Stayed tuned as the next couple month's should be exciting.
Kenny Davis Hotrods (http://www.kdhotrods.com)

[kennyd]

we are real glad to get to work with marty on this project , this is a little out of the "box " for us . most of the cars we have done to this point are streetrods and 55-64 chevys .so to work on a different style car and a different style build is good for all involved. I have a hard time not making them " streetrodish " and making them " industrial " BUT we will work hard to finish this truck and make him proud of it.
PLUS this project has had some killer fab work done on it , the tig welds are the best i have ever seen !

[syborg tt]

we will work hard to finish this truck and make him proud of it.


Screw that - lets just have a good time and finish when we finish

[novanutcase]

Screw that - lets just have a good time and finish when we finish

That's why this truck is so awesome! The attitude of the builder is in the right place!!!:thumbsup:

John

[slownova]

damn, you'all were in my town and didn't make it public? :( :willy:

[TravisB]

damn, you'all were in my town and didn't make it public? :( :willy:


I know kenny will be back at least two more times.....to pick up the 57 and drop the 33 then to pick up the 33

[syborg tt]

I know kenny will be back at least two more times.....to pick up the 57 and drop the 33 then to pick up the 33


Next time I am going to fly in. Driving 1000 miles back and fourth in one day - Sucks

[J2SpeedandCustom]

Next time I am going to fly in. Driving 1000 miles back and fourth in one day - Sucks

Let me know if you need a ride from the airport Marty. Tracy's is just a 30 min drive from there.

[RECOVERY ROOM]

Next time I am going to fly in. Driving 1000 miles back and fourth in one day - Sucks
Drive faster,good visit anyway

[syborg tt]

Drive faster,good visit anyway

Trust me that is why man invented Airplanes.

[RECOVERY ROOM]

Trust me that is why man invented Airplanes.
amen brother!!!

[syborg tt]

Good Day All,

I would like to welcome our new Sponsor - Nitrous Express.
Brian, noticed the truck and said that we needed to work together and I agreed.

http://www.syborgtwinturbo.com/albums/Renderings/NX_400.jpg

www.nitrousexpress.com or [email protected]

Our plans are to build an Intercooler chillier similar to the kit Jerry offers for the Syclones.
However the new kit will be custom built to our Intercooler.

http://www.syborgtwinturbo.com/albums/Build/2007_05_07_chiller.jpg


While were in there we figured we might as well add a little more go-go juice to the motor.
We still haven't decided which kit were going to use but I am certain Brian has something up his sleeve.

http://www.syborgtwinturbo.com/albums/Build/2007_05_07_ml_efi_customerlarge.sized.jpg

[syborg tt]

Guy has been steady working on the Motor.
Collecting parts and working on some old parts that needed some TLC.

Way back in the day (April 2002) I was able to locate a sheet metal Moroso 2 Piece main seal Oil Pan.
Trust me it was very hard to Find.

http://www.syborgtwinturbo.com/albums/Build/2002_04_10_11.jpg


Dennis over at www.highspeedwelding.com trimmed the front cross member (August 2004) so we would be able
to remove the oil pan just in case there were problems with the motor. It's much easier to pull a pan then pull a motor.

http://www.syborgtwinturbo.com/albums/Build/2004_08_26_7.jpg

Dennis added some Simple Bracing to the crossmember for Strength.

http://www.syborgtwinturbo.com/albums/Build/2004_08_31_0.sized.jpg

The Guy's at Rockford Racecraft welded a new pick up to the oil pump to ensure proper oil supply.

http://www.syborgtwinturbo.com/albums/Build/2007_04_30_001.jpg

http://www.syborgtwinturbo.com/albums/Build/2007_05_01_001.jpg

[syborg tt]

The pan has been stripped down and it heading to Kenny's so we can put in the oil return lines.
Once were done with the pan it's heading back to Dave at Comp Fab so we can clean up all of the Welds.

http://www.syborgtwinturbo.com/albums/Build/2007_05_01_002.jpg

Plenty more in store in the next few months.

[[email protected]]

You should change that bad boy over to E85. That way you can run on pump gas.

[syborg tt]

You should change that bad boy over to E85. That way you can run on pump gas.


well there ya go - you've got me thinking again.

Trust me the wheels are turning

[syborg tt]

Good Day All.

Okay it's been a long time coming and were finally back posting updates.
Headed down to Kenny Davis Hot Rods this weekend to work on my truck and get some pictures for you all.
www.kdhotrods.com


My MasterCard Moments from this weekend
1. $450.00 Plane Ticket

2. Free Room & Board at the KD Love Shack

3. Eating Pork at a Steak house

4. Breakfast in the morning and i didn't even have to cook it

5. Learning what the heck a "Holler" is

6. A red scotch brite bad will dull the heck out of a $1500 Polished Billet Specialties rim.

7. Even in Arkansas there are really whacked out People that get to fly on Planes

And best of all.

8. Getting a One off "Used" KD Hot Rods Hat and it even has green paint on it.

http://www.syborgtwinturbo.com/albums/Renderings/2007_05_21_001.jpg

[syborg tt]

Okay time for the real update.

Slid the truck forward from the back of the shop and spent a little time putting it all back together again.

That's Travis looking at the truck. Yep it's low !!

http://www.syborgtwinturbo.com/albums/Build/2007_05_19_003.jpg

If you've ever met Kenny you know he likes them low and slammed to the ground.
We needed to lower the rear just to make him feel comfortable.
Yep it's low enough.

http://www.syborgtwinturbo.com/albums/Build/2007_05_19_005.jpg

Side shot of the rear tire tucked in the wheel well.

http://www.syborgtwinturbo.com/albums/Build/2007_05_19_009.jpg

That's Kenny drawing on the front cover.
We need to make an opening for the Intercooler.
Ps. That Kenny guy is really good with a Marker.

http://www.syborgtwinturbo.com/albums/Build/2007_05_19_020.jpg

Hanging the doors trying to get everything straight before they start doing all of the body work.

http://www.syborgtwinturbo.com/albums/Build/2007_05_19_023.jpg

By the end of the day the doors looked pretty good the fenders were back on and we all came to an agreement on the colors and finishes on the truck.

Plenty more to come in the near future.

Did i mention that he took a red scotch brite pad to my wheel.

[black2002ls]

looking good Marty! Whats the story with the scotch brite and the wheels?

[kennyd]

looking good Marty! Whats the story with the scotch brite and the wheels?


i hated the full polished wheel , so WE decided to brush the centers and leave the ribs polished . he wanted to see it so i used a red scotchbrite to show him . he said he liked it ?

[68protouring454]

kenny, Travis always said you were good on your knee's.........:D

[XcYZ]

This thread is closing in fast on 30,000 views. No surprise, really, this is the baddest truck out there. :bow:

[kennyd]

kenny, Travis always said you were good on your knee's.........:D



Is that were you want to be when Jesus comes?

[68protouring454]

lol, i had to.... there were a few other things i could of touched on, but i went with the knee thing, lol

[syborg tt]

i hated the full polished wheel , so WE decided to brush the centers and leave the ribs polished . he wanted to see it so i used a red scotchbrite to show him . he said he liked it ?


actually i loved it - but i just didn't have the heart to do it.

[CHAZMO1986]

I Don't Mean To Interrupt The Thread, But I Am From Harrison, Ar, And Am Just Wondering Just Where Kenny's Shop Is Located? I'd Sure Appreciate It.

I Have Been Watching The Build Up Of This Truck And Would Love To See It In Person If At All Possible.

You Have Got One Sweetass Ride, Thanks For All The Inspiration

Charles

[TravisB]

we are in avoca ar. Do you know where that is?

[syborg tt]

I almost forgot. The most important thing i learned this weekend is:

If you plan to iron your shirt while your wearing.

What ever you do - God Forbid

Don't hit the Steam Button !!!!

[CHAZMO1986]

No Sir, I Am Not Familiar With That Name.

[Sales@Dutchboys]

Looks good Marty!

Its in good hands!:thumbsup:

[TravisB]

No Sir, I Am Not Familiar With That Name.


we are about 10 min outside of rogers

[Diognes56]

I almost forgot. The most important thing i learned this weekend is:

If you plan to iron your shirt while your wearing.

What ever you do - God Forbid

Don't hit the Steam Button !!!!

:lol: I bet that woke you up. I know reading it woke me up :lol: .

David

[syborg tt]

Actually it wasn't me that got "Steamed". It was one of Kenny's buddy's and i seem to think Kenny also may have "Steamed" himself at one time.

ps - you should have seen the marks on his stomach. I almost wet my pant's when the guy told me what he did. If I new him better I may have laughed a little longer.

[sick65]

Glad to see you finally made it home Marty. I had a blast talking about the build on the plane. The truck is definitely going to be one of a kind. I look forward to Indy in a few weeks.

[NU BREED]

MARTY,REALLY GREAT THREAD,,REALLY GREAT TRUCK !!!! I SEE ITS BEEN A LONG TIME COMING FOR YOU ALSO.FEELS GOOD TO SEE SOME LIGHT AT THE END OF THE TUNNEL FINALLY..HOPEFULLY WE WILL BOTH BE ROLLIN SOON.:thumbsup:

[deuce_454]

dude turn off your caps lock when posting

[syborg tt]

Glad to see you finally made it home Marty. I had a blast talking about the build on the plane. The truck is definitely going to be one of a kind. I look forward to Indy in a few weeks.

Heck i wasn't sure if i was going to make it home with that crazy guy on the plane. It was close the Flight Attendants wanted him off the plane and the Pilot said that he would have to freak out just a little more and then they would kick him off. The good thing was they put the big muslce bound guy next time him for the remander of the flight and that did quiet him down just a little.

I am glad you liked the build book - it should be cool to see it completed.

Yep - Indy - Can't wait !!! :thumbsup:

[87wildside]

By any chance is this the truck with the A-pilars reshaped to flow with the top of fenders? If so do you have any pics?
BTW, this truck is freakin awsome!:hail:

[syborg tt]

By any chance is this the truck with the A-pilars reshaped to flow with the top of fenders? If so do you have any pics?
BTW, this truck is freakin awsome!:hail:


yep thisis the truck. I'll try to post pics tonight or tommorow when i find them.

[syborg tt]

Okay I know we've been a little sleepy with the updates. But not to worry were working on the trucks. Just trying to gather parts for the engine.

Guy at Rockfordracecraft has been working with Jessels on the Lifter and shaft mount rockers. Once we have those we should be pretty close to sealing up the motor.

On a side note Ron ( Wilson Muscle Cars ) and & I have been workng on the locking versions of the hood pins. We just want to have options.

http://www.syborgtwinturbo.com/albums/Build/2007_06_05_hp_locking_6.jpg

http://www.syborgtwinturbo.com/albums/Build/2007_06_05_hp_locking_7.jpg

http://www.syborgtwinturbo.com/albums/Build/2007_06_05_hp_locking_8.jpg

http://www.syborgtwinturbo.com/albums/Build/2007_06_05_hp_locking_9.jpg

[TravisB]

marty those are awesome...I will definatly take a set of those for the chevelle. I like the no pin and flush fit....very nice

[syborg tt]

By any chance is this the truck with the A-pilars reshaped to flow with the top of fenders? If so do you have any pics?
BTW, this truck is freakin awsome!:hail:

shoot me an e-mail and i'll send you some pics

[email protected]

[syborg tt]

Good Day All,

I know it's shocking actually it's amazing.
We have Pictures - only 3 but we actually have Pictures.
Yahooooooo!!!

This is the first Photo (using the term photo loosely here)
I think it's the side of the truck with some string running down it.

http://www.syborgtwinturbo.com/albums/Build/2007_06_20_023.jpg

Yep I was correct -- it's the side of the truck.
The Guy's are actually working on aligning the bed width with the cab width.
This is not for the faint at heart

http://www.syborgtwinturbo.com/albums/Build/2007_06_20_024.jpg

The side has been pulled out to match the widest part of the cab.
Next, they are going to cut the back of the cab and pull it out to match the side of the bed.
Our goal is to have a perfectly straight line down the side of the truck.

http://www.syborgtwinturbo.com/albums/Build/2007_06_20_025.jpg


I can't wait to see it in person.
But for now I will just have to live with Pictures.

ps - not to worry new camera is on the way.

[Sales@Dutchboys]

Looking good Marty,

Cant wait to see it in person!:thumbsup:

[frankenstang]

You guys have issues, man. This is like the longest thread in HISTORY!! I wanna see a finished truck, I need CLOSURE!!!!!



BTW, keep it up, Best looking S/T truck in the world.

[syborg tt]

You guys have issues, man. This is like the longest thread in HISTORY!! I wanna see a finished truck, I need CLOSURE!!!!!


LOL - you need closure, my wife needs closure. I just broke the bad news to her that we are going to be starting the next project soon. She almost died!!

wow - i just realized we are at the 2 year mark. EAK !!!!!!

[ZZ3ElCamino]

Hey Marty, maybe I need to catch up on this thread, but what will the next project be?

Jason

[syborg tt]

Hey Marty, maybe I need to catch up on this thread, but what will the next project be?

Jason

Chevelle - Looks like it may even be a convertible

[kennyd]

hey , i know where one is .

[syborg tt]

hey , i know where one is .

you better have one

[TravisB]

you better have one


And I can help with a name for it

Xcoupe
Xhrtd

anything that would indicate it use to have a roof on it ha ha. That would be a very cool project for sure. We have pics of the car layed on the ground with a set of D engineering wheels on it. NICE:thumbsup:

[Leadfoot1]

Travis,

You can't say "we have pics, bla bla bla" and then not post 'em up...

'Gotta show us now.

;-)

Lead.

[TravisB]

Travis,

You can't say "we have pics, bla bla bla" and then not post 'em up...

'Gotta show us now.

;-)

Lead.


Sorry for the tease lead but they are on a diff PC. I think kenny may have some of the car on his computer at work.

[syborg tt]

Sorry for the tease lead but they are on a diff PC. I think kenny may have some of the car on his computer at work.

Now that's funny - Kenny post pics of a car on the Internet.

Think they will be blurry or clear ??:lol: :lol: :lol: :lol: :lol:

[kennyd]

Now that's funny - Kenny post pics of a car on the Internet.

Think they will be blurry or clear ??:lol: :lol: :lol: :lol: :lol:



the funny part is , yes i have photos , no i really dont know how to get them from one computer to the other so i can upload them ????


sorry i build cars , not a computer geek .

[Roger Poirier]

You guys have issues, man. This is like the longest thread in HISTORY!! I wanna see a finished truck, I need CLOSURE!!!!!

LMAO - Me too. Please start a new thread if and when this project is complete.

Thanks.

[syborg tt]

LMAO - Me too. Please start a new thread if and when this project is complete.

Thanks.

really we plan to finish this truck we even have a goal.

[Blake Foster]

Hey Marty
I'm with the other guys. tell your banker this has gone on long enough and ti's time to let us all get on another band wagon. time for some tire smoke.............. hahahahahahhahahhahaha
you still need to send me the secret recipe for getting parts!!!!
take it easy
later
Blake

[T Bell]

what's the latest? I have been so inspired that I've found a S-10 extended cab at my brother in laws mom's house. He says it has sat there for 8 years. Reason: some wire that they didn't fix shorted and burned the engine bay. But if I can get it for next to nothing, I'll take it on.

[kennyd]

what's the latest? I have been so inspired that I've found a S-10 extended cab at my brother in laws mom's house. He says it has sat there for 8 years. Reason: some wire that they didn't fix shorted and burned the engine bay. But if I can get it for next to nothing, I'll take it on.

i will anwser this question because i have it in our shop , we have the bed off and cut the bedsides off so we can make the bed wider so the sides look flat . then we made the front bed panel square because it was round and did not look good . also we made the tailgate fit the hole .
next we reinstall the bed and cut the cab and widen it to fit the bed .
dont ask for photos ! lol i will have marty some after we install the bed .

[syborg tt]

dont ask for photos ! lol i will have marty some after we install the bed .

Okay Guy's I've sent him a camera and i know he's taken pictures ( 24 i think ) and he's holding them hostage and won't share them.

Anyone want to go over to Kenny's shop and see if you can convince him to hit the send key on his computer. Mind you, you better be a big guy because he's a biggen and he might kick your ars. :_paranoid

[sick65]

Okay Guy's I've sent him a camera and i know he's taken pictures ( 24 i think ) and he's holding them hostage and won't share them.

Anyone want to go over to Kenny's shop and see if you can convince him to hit the send key on his computer. Mind you, you better be a big guy because he's a biggen and he might kick your ars. :_paranoid

Just send over his wife. I know she can whip his ars. If not, I'm sure Trav could give him a run for his money. :lol:

[syborg tt]

Hey Marty
I'm with the other guys. tell your banker this has gone on long enough and ti's time to let us all get on another band wagon. time for some tire smoke.............. hahahahahahhahahhahaha
Blake


Really it's going to get done - we even have a goal

[TravisB]

Just send over his wife. I know she can whip his ars. If not, I'm sure Trav could give him a run for his money. :lol:


I almost out weight him.......lol. He loses a bit more weight and I will ha ha.

[syborg tt]

I almost out weight him.......lol. He loses a bit more weight and I will ha ha.


not to worry i don't see Kenny going on a diet anytime soon. :unibrow:

[kennyd]

not to worry i don't see Kenny going on a diet anytime soon. :unibrow:
liquid diet !

[syborg tt]

liquid diet !


Really i just can't see you salting a can of "Slim Fast."

Just doesn't seem possible but you never know.

[kennyd]

Really i just can't see you salting a can of "Slim Fast."

Just doesn't seem possible but you never know.


hey that really aint that bad .

[sick65]

not to worry i don't see Kenny going on a diet anytime soon. :unibrow:

Since the Indy trip, He's hooked on pancakes.:rofl:

YOU GOT PANCAKES????

[kennyd]

Since the Indy trip, He's hooked on pancakes.:rofl:

YOU GOT PANCAKES????

thats funny

inside joke

[novanutcase]

Actually, I hear Kenny works out all the time! 12oz. curls..............

John

[87wildside]

Thanks for the a-pilar pics Marty. That looks a lot simpler then what I was planning. Hope you don't mind if I use you idea. :D

[syborg tt]

Thanks for the a-pilar pics Marty. That looks a lot simpler then what I was planning. Hope you don't mind if I use you idea. :D


Your welcome and not a problem have at it. That's why i post pics.

[syborg tt]

Good Morning All,

The Guy's at Kenny Davis Hot Rods have been hard at work with way to many projects.
Dads 57 is back at the shop and the Camaro they are working on is just incredible.
Looks like it's time for another road trip to see all of them.

http://www.syborgtwinturbo.com/albums/Renderings/Autometer.jpg

All the hard work is paying off, I can add one more hat to my collection.
We wanted a gauge set that would compliment the truck's theme and Autometer was the only Choice.
The new Automaker's gauges will look right at home in the Dash of Syborg.

http://www.syborgtwinturbo.com/albums/Build/2007_07_02_001.jpg

It's hard to believe that all but one of these gauges are going to fit in the Dash.
3655 Sport Comp II Water Temp
3692 Sport Comp II Volt
3656 Sport Comp II Oil Temp
3603 Sport Comp II Boost (mechanical)
3663 Sport Comp II Fuel Pressure
3653 Sport Comp II Oil Pressure
3616 Sport Comp II Fuel Level
3688 Sport Comp II Speedo
3697 Sport Comp II Tach

Mounted in the Center Consule
3657 Sport Comp II Trans Temp

http://www.syborgtwinturbo.com/albums/Build/2007_07_02_002.jpg

Every Guage was specifically choosen.
Five of the Small Guages are Full Sweep / Two of them are Partial Sweep
The two Partial Sweep guages will be mounted in the outside triangle of the dash layout.

http://www.syborgtwinturbo.com/albums/Build/2007_07_02_004.jpg

I'm really looking forward to seeing if we can hit 160mph with this mini-truck.

http://www.syborgtwinturbo.com/albums/Build/2007_07_02_005.jpg

[syborg tt]

It looks like the cab is off and heading to the Powder Coater.
The entire inside of the cab will be coated Satin Black.
Once the cab is back the outside corners will be filled with lead to smooth the gap between the cab and the bed.

http://www.syborgtwinturbo.com/albums/Build/2007_07_08_015.jpg

The chassis moved off to the side waiting to meet up with the body again.

http://www.syborgtwinturbo.com/albums/Build/2007_07_08_016.jpg

http://www.syborgtwinturbo.com/albums/Build/2007_07_08_017.jpg

Wait, that's the Chevrolet Gate - what happened to the other gate.

http://www.syborgtwinturbo.com/albums/Build/2007_07_08_018.jpg

That's it for today. Maybe I'll post and update on the Garage project I started in January.

ps - wait till you see the sweet T-shirt that Autometer sent me.

[RECOVERY ROOM]

i still say that it will make a great cooler hauler in to the shows. lol!:cheers:

[Mick Mc]

Marty
I that your garage?
How big is that garage?
It looks like the perfect size for some of my projects...

Mick

[kennyd]

Marty
I that your garage?
How big is that garage?
It looks like the perfect size for some of my projects...

Mick

it's my shop , 40x100 , 10ft side walls . if i had it to do again i would make it 50x100 and 16 ft walls so i could 2 story the last 50x50 for storage .
the 40 wide is ok , but you can make alot more work space if you can turn the cars 90 degrees to the wall . with the 40 the cars have to be at a angle to leave room to drive down the center .
we are going to build a 2nd shop 40x50 for " clean cars " only to assemble in .

[race-rodz]

uh oh...marty took pics of the classified camaro project... those mini truckers have no respect:D

[kennyd]

uh oh...marty took pics of the classified camaro project... those mini truckers have no respect:D
i dont have problems showing the car unfinished , i would like to keep the rendering undercovers to a few . we will have the rushforth art at columbus to show a limited group .
i hate to be this way but we were forced this hand by the owner and another shop .

[syborg tt]

uh oh...marty took pics of the classified camaro project... those mini truckers have no respect:D

Not me - those are Kenny's pics. If they were my Pics they wouldn't be blurry.

Heck i just bought a tri-pod for Kenny it looks like he needs it.

[kennyd]

Not me - those are Kenny's pics. If they were my Pics they wouldn't be blurry.

Heck i just bought a tri-pod for Kenny it looks like he needs it.


bring it to columbus , that will save you frieght .

[syborg tt]

bring it to columbus , that will save you frieght .

trust me the Tri-Pod is packed up and ready to go.

[68protouring454]

marty, you had better watch out, from what I have heard, Kenny might try to make you a tripod.......:_paranoid

[syborg tt]

marty, you had better watch out, from what I have heard, Kenny might try to make you a tripod.......:_paranoid

i'm quessing that explains why he asked me if he could room with me in Columbus

[syborg tt]

what's the latest? I have been so inspired that I've found a S-10 extended cab at my brother in laws mom's house. He says it has sat there for 8 years. Reason: some wire that they didn't fix shorted and burned the engine bay. But if I can get it for next to nothing, I'll take it on.


Well - did ya buy it. I gotta know

[syborg tt]

MARTY,REALLY GREAT THREAD,,REALLY GREAT TRUCK !!!! I SEE ITS BEEN A LONG TIME COMING FOR YOU ALSO.FEELS GOOD TO SEE SOME LIGHT AT THE END OF THE TUNNEL FINALLY..HOPEFULLY WE WILL BOTH BE ROLLIN SOON.:thumbsup:


Thank you very much. I really can't wait to see the truck with color let alone finished. How's your camaro coming along ??

[Blake Foster]

Marty

When can we see it painted,
maybe a pm is in order

[syborg tt]

Marty

When can we see it painted,
maybe a pm is in order


From one of my Favorite Movies the Money Pit

Two Weeks ..........:rofl:

[TravisB]

two weeks that is the funniest thing I have heard all day

[syborg tt]

Good Morning All,

Quick Update.......

http://www.syborgtwinturbo.com/albums/Renderings/AIRlogo.jpg

I met with the guy's from Air Ride at Indy Good Guy's.
After Talking with Jeremy we decided that we needed to upgrade the suspension on Syborg to the new Level Pro system.

http://www.syborgtwinturbo.com/albums/Renderings/levelprologo.jpg

Normally I would show you pictures of the actual parts but then we all know Kenny's not good with Pictures.
So the good guy's at Air Ride sent me there catalog images just in case.

Below is the new ARC4000L System.
It has some pretty cool features instead of me telling you in my words I figured it would be easier to just do a cut and past from Air Rides Site.

http://www.ridetech.com/productinfo/levelpro.asp

http://www.syborgtwinturbo.com/albums/Renderings/arc4000_features.jpg

There new Pocket size remote control.

http://www.syborgtwinturbo.com/albums/Renderings/REM7500.jpg

http://www.syborgtwinturbo.com/albums/Renderings/arc4000L.jpg


The new LevelPro™ leveling system is the most advanced air suspension control system available today.
It is the result of several years of development by “hands on” engineers and refinement in real world vehicles.

The LevelPro™ system uses a unique combination of ride height sensors AND air pressure sensors to quickly achieve your selected ride height.
By comparing the position of the ride height sensor to the air pressure the vehicle is leveled with no crossloading.


FEATURES
• More accurate leveling of ride height sensors in addition to air pressure sensors allows extremely accurate vehicle leveling with no crossloading

• Better air pressure sensors
New voltage based air pressure sensors eliminate EMI interference and grounding problems that can lead to inaccurate pressure readings and ride heights. This new voltage based sensor has more resolution [accuracy] and quicker response to allow faster and more accurate air pressure presets. It’s also smaller in diameter to allow direct installation into the RidePro® and BigRed solenoid blocks to eliminate remote mounting panels with extra lines and fittings.

• Easier viewing in bright light from any angle
VFD [vacuum florescent display] instead of an LCD [liquid crystal display]

• Ride-height-on-start
Each time the vehicle is started it will automatically go to highway ride height.

• Control panel programming
All programming [including the ride-height-on- start feature] can be accessed from the control panel so you can hide the ECU and still have easy access to all programming functions.

• 3 ‘1 touch’ ride height presets
Accessible from control panel.
These ride heights are programmed by a simple push and hold action similar to programming a radio station preset.
No secret sequence of buttons to push!

• Backlit soft touch silicone buttons
Easier actuation by feel, no diverting your eyes from the road to see which button you're pushing!

• Extruded aluminum ECU
More robust to avoid physical damage during installation

[Porterbuilt]

The Level Pro is a pretty cool system... the one annoyance is that is "pulses" while setting itself to the programmed height(s). Fortunately the guys at Air Ride came up with a new chip board to eliminate the "pulsing". Make sure you get it now... or you will have to get it later.:)

Can't wait to see the truck done.

[T Bell]

Well - did ya buy it. I gotta know

still in the works. I think my brother in law is a sketsophrenic, selfish, wanna be a car guy, sorry mofo! From what I understand he may be looking into it for himself after selling me on the idea. The saga continues though.

[syborg tt]

Good Afternoon All,

The cab is back from the Powder Coaters.
Kenny said it looks really good and he's very happy.

Instead of media blasting the cab to remove all of the paint they decided to cook it off.
How would you like to be in that oven?

http://www.syborgtwinturbo.com/albums/Build/2007_08_01_0.jpg

He's got one of those Tripods and he still takes blurry pics.
Travis can you please help him or do I have to buy him one of those steady shot camera's?

http://www.syborgtwinturbo.com/albums/Build/2007_08_01_2.jpg

Wait he must have gotten the Tripod out for this picture.
Seems down south they will do anything for a great but shot.

Ps - I've spared everyone's eye's and painted in a longer shirt.

http://www.syborgtwinturbo.com/albums/Build/2007_08_01_1.jpg

Truth be told if anyone is every looking for a great shop to work with the guy's at
Kenny's shop are a blast to work with. They are totally laid back and have way to much fun.
www.kdhotrods.com

[black2002ls]

I love the way the cage looks, can't wait to see some paint on this beast!!!

[TravisB]

thats not my ass this time boys.......just want that to be clear

[syborg tt]

thats not my ass this time boys.......just want that to be clear


really i want to make a comment here.

butt..........................

[T Bell]

you guys are funny. since he's in the south, instead of a tripod why don't you buy him a deer stand. that will make him and you happy. ;)

[syborg tt]

you guys are funny. since he's in the south, instead of a tripod why don't you buy him a deer stand. that will make him and you happy. ;)


No

No

No

No

He might mistake a gun for a camera and then i'll end up with holes in my truck.

Not good :_paranoid

[syborg tt]

wait wait i got lets make a Bear Stand.

[T Bell]

lol. I just got off the phone with my brother in laws mother:_paranoid , she said I could get the truck for $200. V6, auto, extended cab, I think it's a 92 or so. Not sure when they went to the rounded body for the S-10s. I'd have to replace all wires and plastic under the hood because of the fire. What do ya think?

[syborg tt]

lol. I just got off the phone with my brother in laws mother:_paranoid , she said I could get the truck for $200. V6, auto, extended cab, I think it's a 92 or so. Not sure when they went to the rounded body for the S-10s. I'd have to replace all wires and plastic under the hood because of the fire. What do ya think?

shoot me some pics ( [email protected] ) if the body is good and they have a title i'd buy it.

[T Bell]

we'll do. It will have to be this weekend, though. From what I'm told it's a 4.3L if that tells you about what year it is.

[syborg tt]

Good Morning All,

As you know the cab is back from the Powder Coaters and ready to get some Primer to Protect it.

What is shocking is that Kenny took these pics at 6:37am on a Saturday Morning.

http://www.syborgtwinturbo.com/albums/Build/2007_08_04_001.jpg

http://www.syborgtwinturbo.com/albums/Build/2007_08_04_002.jpg

http://www.syborgtwinturbo.com/albums/Build/2007_08_04_003.jpg

http://www.syborgtwinturbo.com/albums/Build/2007_08_04_004.jpg

Look Mom - No Overspray.

http://www.syborgtwinturbo.com/albums/Build/2007_08_04_005.jpg

[Garage Dog 65]

Getting close now !!! It's great to see a project all in the same color - even when it's primer. Can't wait to see it painted !

Jim

[Steve Chryssos]

Nice. It kinda looks like the space shuttle up on its end like that. :patriot:

[kennyd]

wow ! no comment on how nice the photos are ? no blurry photos , focused ,
i have a real steady hand at 6.30 am.

[MarkM66]

Instead of media blasting the cab to remove all of the paint they decided to cook it off.
How would you like to be in that oven?



Do you guys usually have the paint baked off? How do you like the results? Hows the cost compared to having it blasted? Any chance of the metal getting to hot, and warping?

I have a place near me that does it, but I don't know of anyone who's used it.

[TravisB]

Do you guys usually have the paint baked off? How do you like the results? Hows the cost compared to having it blasted? Any chance of the metal getting to hot, and warping?

I have a place near me that does it, but I don't know of anyone who's used it.


martys cab didnt warp.........and the sheetmetal on it is way thinner than an older car. Looked nice when completed.

[kennyd]

i didn't know they were going to bake it off , but i did not warp the metal at all . i dont know if i would do a car with big 1/4 panels .

[wiedemab]

Baking of the body shouldn't cause any of the metal to warp. Warpage (if that's a word) is caused by a concentration of heat in one area. The expansion of the heated area, which is constrained by the metal around it causes a wave in the metal. If the oven heats it evenly it shouldn't cause any problems.

Unlike materials that are bonded together that expand at different rates would cause problems, but I think in the case of an all steel body you should be OK.

BTW - the truck looks SWEET! I think I've seen enoughs ass for a while though!

Later,

Brandon

[syborg tt]

Good Morning All,

The Cab is back on the frame,
Once the cab and bed are back on they are going to start fitting the ground effects.

http://www.syborgtwinturbo.com/albums/Build/2007_08_13_001.jpg

Front clip is back on to check fitment

http://www.syborgtwinturbo.com/albums/Build/2007_08_19_0.jpg

Bed is back on.

http://www.syborgtwinturbo.com/albums/Build/2007_08_19_1.jpg

The guy's set the gap between the bed and the cab.
It's starting to look like a truck again.

http://www.syborgtwinturbo.com/albums/Build/2007_08_19_2.jpg

Yep this is the way it should look when you look down the side of the truck.

http://www.syborgtwinturbo.com/albums/Build/2007_08_19_3.jpg

[TravisB]

I hope everyone notices how straight it is because it was a lot of work.

[RECOVERY ROOM]

That truck is going to haul a$$,great bed to cab gap,that has always been a sore spot on them,are you tired of blocking on them sides Travis

[TravisB]

That truck is going to haul a$$,great bed to cab gap,that has always been a sore spot on them,are you tired of blocking on them sides Travis


not yet but I have a feeling I will be. I tried calling your cell the other day and it went straight to vmail. Turn on your dam phone LOL.....J/K:thumbsup:

[black2002ls]

VERY nice. I know all about looking down the side of a truck and not liking what you see. I've had an 02 and 03 in the past year and a half and its just terrible how bad the transition from the cab to the bed looks.

[71Cuda]

Dang, Marty, your truck is simply incredible!! :wow: :faint: Awesome concept and meticulous execution!! :thumbsup:

[HRBS]

Looking very nice Marty... slick looking truck !

[kennyd]

after SEMA this " mini truck " will get done fast . when you see the fab work in this truck you will be amazed .

[ironworks]

Lookin good, Marty

Rodger

[syborg tt]

after SEMA this " mini truck " will get done fast . when you see the fab work in this truck you will be amazed .


"mini truck" - you crack me up

[RECOVERY ROOM]

not yet but I have a feeling I will be. I tried calling your cell the other day and it went straight to vmail. Turn on your dam phone LOL.....J/K:thumbsup:
Travis call the shop 402 235 3800 i only use cell phone when travling,cell phone won't work in metal building

[87wildside]

:willy: Any updates?

[kennyd]

:willy: Any updates?

yes the truck is still being worked on a little at a time . right at this time we are all hard on the camaro .
we will have some updates later this week .

[Phewes]

looking good man.. cant wait to see it painted finally!

[syborg tt]

Good Morning,

The guy's have been hard at work on the Sema Camaro.
However they are still working on the truck.

Right now they are working on fitting the bed cladding.

http://www.syborgtwinturbo.com/albums/Build/2007_09_11_001.jpg

The cladding now sits on the side of the truck perfectly without any stress.
I am so happy we made everything in Fiberglass.
www.syclone-typhoon.com

http://www.syborgtwinturbo.com/albums/Build/2007_09_11_002.jpg

The tailgate is finally fit - This was a big pain in the ars.
You can also see that the Rear Cover is going to need to be widened
The gap from the Factory is almost 1/2" - not good

http://www.syborgtwinturbo.com/albums/Build/2007_09_11_003.jpg

PS - your not going to believe me but Kenny didn't take these pictures Travis did.

[Garage Dog 65]

If I remember right from this summer when I met everyone - all these people work a full-time job, PLUS working nights and weekends in this shop building these cars (and trucks).

THAT is absolutely amazing work and progress !!

I can only imagine the partying this crew will do at SEMA !

[kennyd]

If I remember right from this summer when I met everyone - all these people work a full-time job, PLUS working nights and weekends in this shop building these cars (and trucks).

THAT is absolutely amazing work and progress !!

I can only imagine the partying this crew will do at SEMA !


yes , we all work day jobs
travis is a insurance adjuster for nationwide 40 ish a week
dad is a big wig for tyson foods 40 ish
i run a 15 man bodyshop 40 ish
tyler is a bodyman for me at the bodyshop 35ish

and we all work a xtra 35 hrs in the hotrod shop !

[TravisB]

If I remember right from this summer when I met everyone - all these people work a full-time job, PLUS working nights and weekends in this shop building these cars (and trucks).

THAT is absolutely amazing work and progress !!

I can only imagine the partying this crew will do at SEMA !


Yup thats us....workaholics. We will definatly be ready to relieve some stress in vegas and we have been known to do some partying:unibrow: :unibrow:

I will get you better pics marty be calm my friend

[HRBS]

1st: Looks great Marty.

2nd: I too am a part-timer. I work 40hrs a week as an Architect designing houses and put 35hrs a week nights and weekends at my shop designing and building hot rods.:willy:

3rd: I need a "party break" as well ... SEMA will be fun !

[syborg tt]

I work about 50 hours a week Day job

When the truck was here I was at the chassis shop working about 15 hours a week - excluding the 60 minute commute each way. Now that the truck is at Kenny's i've actually had some free time to go Mountain Biking and I even did my first race in 12 years.

I am still selling parts about 20 hours a week so i can pay for this habbit plus i'm working on the build book and website.

[Garage Dog 65]

Wow, I feel like a total slacker ..... working 'only' 12 hours days trying to help keep our airline afloat - then I go home and basically do a little of nothing.

You guys amaze me and really deserve that party time at SEMA ! Enjoy.

[syborg tt]

Good Morning All,

It's like Christmas in September.
The crew at Bowler Transmission built the new transmission for Syborg and I can't wait to see it in the truck.

http://www.syborgtwinturbo.com/albums/Renderings/bowler.thumb.gif

Kenny and Travis both said it's a really nice looking piece.

http://www.syborgtwinturbo.com/albums/Build/2007_09_20_2.jpg

The only problem is that Travis had to help Kenny lift trans out of his truck.
Seems Kenny's been eating to many donuts and skipping the gym.

http://www.syborgtwinturbo.com/albums/Build/2007_09_20_1.jpg

I'm really happy to be working with the Guy's & Gals at Bowler they are a top notch crew.
I am also very happy that they wanted to be part of my project.

[boonedog]

any updates?

[boonedog]

any updates?

[TravisB]

any updates?

probably not til after SEMA

[boonedog]

thanks ill be waitn:yes:

[syborg tt]

Good Morning All,

I know it's shocking - I am actually doing an update before Sema.

Well, it looks like more parts are flying in.
We contacted the guy's at Jesel and they were kind enough to help us with the part numbers
of everything we needed to get the Pontiac Heads put together.

Once we had all of the part Numbers I called Scoggin Dickey Parts Center
www.sdpc2000.com -- these guy's are top notch and there prices are dirt cheap.

http://www.syborgtwinturbo.com/albums/Build/2007_10_25_1.jpg

Close up of the Rocker Arms - .450 Offset

http://www.syborgtwinturbo.com/albums/Build/2007_10_25_2.jpg

Offset Lifters

http://www.syborgtwinturbo.com/albums/Build/2007_10_25_3.jpg

http://www.syborgtwinturbo.com/albums/Build/2007_10_25_4.jpg

ps -- don't ask how much this cost and please don't tell the wife.

[deuce_454]

compared to the crank i bet it was a bargain

[syborg tt]

compared to the crank i bet it was a bargain

yep- that is the trutch

[syborg tt]

Good Morning All,

Guy over at Rockford Racecraft is kicking butt on my Engine.
www.rockfordracecraft.com

He is trying to get it together by the end of next week.

http://www.syborgtwinturbo.com/albums/Build/2007_10_29_0.jpg

Just think that little engine is going to make some big Horsepower.

http://www.syborgtwinturbo.com/albums/Build/2007_10_29_2.jpg

Man I hate to cover them up -- they look so nice.

http://www.syborgtwinturbo.com/albums/Build/2007_10_29_4.jpg

The parting Shot

http://www.syborgtwinturbo.com/albums/Build/2007_10_29_5.jpg

Thanks again guy for jumping in and getting this motor put together so quickly.

[syborg tt]

Good Afternoon All,

Okay we've done a little changes to the motor.
Guy pulled the old Camshaft out and installed the new John Meaney Spec'd cam.

http://www.syborgtwinturbo.com/albums/Build/2007_11_01_5.jpg

Guy Installed the New Cometic Head Gaskets.
A Big Thanks to Mike Lee at RPM for getting them out so Quick.

http://www.syborgtwinturbo.com/albums/Build/2007_11_10_0.jpg

Just like this picture

http://www.syborgtwinturbo.com/albums/Build/2007_11_10_3.jpg

Measuring up for Push Rods

http://www.syborgtwinturbo.com/albums/Build/2007_11_12_1.jpg

Opps - need to clean up this area a little more.

http://www.syborgtwinturbo.com/albums/Build/2007_11_13_2.jpg

[syborg tt]

Okay - were not really sure why this wire is in the head.
It's been in every new Pontiac head I've ever had.

http://www.syborgtwinturbo.com/albums/Build/2007_11_16_3.jpg

Pics of the Wire's

http://www.syborgtwinturbo.com/albums/Build/2007_11_16_4.jpg

Josh over at Rockford Racecraft - making up some room.

http://www.syborgtwinturbo.com/albums/Build/2007_11_16_7.jpg

Looking good.

http://www.syborgtwinturbo.com/albums/Build/2007_11_16_9.jpg

[syborg tt]

Good Afternoon All,

Back From Sema and Kenny is hard at it.
The Rocker Cladding has been extensivly modified.
New mouting provisions have been made to ensure a good quality fit.

http://www.syborgtwinturbo.com/albums/Build/2007_11_15_0.jpg

You can see Kenny is going to make this truck as straight as can be.

http://www.syborgtwinturbo.com/albums/Build/2007_11_18_0.jpg

http://www.syborgtwinturbo.com/albums/Build/2007_11_18_1.jpg

The gap between the bed and cab has been fixed

http://www.syborgtwinturbo.com/albums/Build/2007_11_18_2.jpg

Just your token Blurry Kenny Davis Shot.

http://www.syborgtwinturbo.com/albums/Build/2007_11_18_3.jpg

More to come next week

[ccracin]

Marty,

Those wires could be from the cores used in the casting process. I've seen wires like that used to hold several cores together or in place. Although that is in steel castings and they normally are made of an alloy that melts away where exposed to the liquid metal. I'm not real familiar with the aluminum casting processes. Just a guess. Looking bad a$$ by the way. Keep the pics coming. Gotta love these trucks!

Later.

[s10kool]

man i have said it before and well JUST ONE KILLER RIDE :thumbsup:

hey marty who is gonna do the interior

if you dont have any lined up - i know it is a drive but my buddy here in kansas does the interior for Fast Eddie Hot Rods in Lamar Mo. and the tv show Trick My Truck and other killer show cars and is killer on quality and price
if interested let me know

[kennyd]

man i have said it before and well JUST ONE KILLER RIDE :thumbsup:

hey marty who is gonna do the interior

if you dont have any lined up - i know it is a drive but my buddy here in kansas does the interior for Fast Eddie Hot Rods in Lamar Mo. and the tv show Trick My Truck and other killer show cars and is killer on quality and price
if interested let me know
is it scott drager ?

[syborg tt]

Thank you very much.

We are going to be using Tracy Weaver from the Recover Room (http://www.recoveryroomrodinteriors.com/) for the interior. He did my dad's 57 and it turned out great. I'm very happy with him and plan to use him on my next few projects.



man i have said it before and well JUST ONE KILLER RIDE :thumbsup:

hey marty who is gonna do the interior

if you dont have any lined up - i know it is a drive but my buddy here in kansas does the interior for Fast Eddie Hot Rods in Lamar Mo. and the tv show Trick My Truck and other killer show cars and is killer on quality and price
if interested let me know

[Garage Dog 65]

Looking great guys ! Won't be long now. PS, Love that little motor !

[tjbruning]

Look good! :thumbsup:

[s10kool]

is it scott drager ?
HAHA NOT SCOTT

OZ DOES THE INTERIORS SCOTT DID THE FIRST SEASON AND HASNT SINCE
BUT IF ANYONE WANTS TO GIVE OZ A CALL LET ME KNOW:thumbsup:

not a problem marty i know what ya mean

[Blake Foster]

Hey Kenny..................... lay off the juice when you know you need to pick up the camera. damn.............. Marty maybe you should get him a tripod!!!

[kennyd]

Hey Kenny..................... lay off the juice when you know you need to pick up the camera. damn.............. Marty maybe you should get him a tripod!!!


get it right travis is the juice boy , i have a camera in one hand and a sonic burger in the other . lol
tripod ..... is that that thing marty sent ?

[syborg tt]

get it right travis is the juice boy , i have a camera in one hand and a sonic burger in the other . lol
tripod ..... is that that thing marty sent ?

Yep - that was a tri-pod that I gave you. It's pretty cool all of the big shops use them.

Just in case you can't figure out the Tri-pod you could alway's set the camera on a cardboard box.

[TravisB]

I dont think that is the kind of juice he as talking about.....

[syborg tt]

Good Afternoon,

I'm a little late getting this e-mail out.

Kenny is really kicking butt on the body mods. He is making sure everything fits perfect.

Hard to tell from this picture but you can see Kenny has widen the rear cover to have a 3/16" gap.

http://www.syborgtwinturbo.com/albums/Build/2007_11_23_KD_0.jpg

Tailgate has been smoothed.

http://www.syborgtwinturbo.com/albums/Build/2007_11_24_KD_0.jpg

You can also see the side of the gate has also been filled.

http://www.syborgtwinturbo.com/albums/Build/2007_11_24_KD_1.jpg

Cab is ready for Primer. The cab has been widened 3/16" to line up with the bed sides.

http://www.syborgtwinturbo.com/albums/Build/2007_11_25_KD_0.jpg

Yep, The bed has been extensively work to make sure t fits perfectly with the cab.

http://www.syborgtwinturbo.com/albums/Build/2007_11_25_KD_1.jpg


Next week the truck should look a little different as it will all be one color.

[J2SpeedandCustom]

That is one bad mini truck!!

[Blake Foster]

hahaahh Kenny your f'ed up................ i love it..

[awr68]

That's one hell of a lot of work and it looks great! How's the wheels holding up in the shop environment? My first set of wheels got some scratches from all the grinding dust.

[kennyd]

That's one hell of a lot of work and it looks great! How's the wheels holding up in the shop environment? My first set of wheels got some scratches from all the grinding dust.


they all do , BUT we send them to a polisher before the car leaves and get them re-polished

[kennyd]

hahaahh Kenny your f'ed up................ i love it..


wow , that must be true , because everyone says that .

[Nate Hanson]

Looking Good Marty! :D

[syborg tt]

Hi All,

Kenny is really cranking on the Bodywork.

http://www.syborgtwinturbo.com/albums/Build/2007_12_03_KD_0.jpg

Looking down the side of the truck

http://www.syborgtwinturbo.com/albums/Build/2007_12_03_KD_1.jpg

You can see that Kenny has fitted the cladding with the fender.
There used to be a 1/2" gap

http://www.syborgtwinturbo.com/albums/Build/2007_12_03_KD_2.jpg

Just a quick shot with the Side Cladding on the Truck.

http://www.syborgtwinturbo.com/albums/Build/2007_12_03_KD_3.jpg


http://www.syborgtwinturbo.com/albums/Build/2007_12_03_KD_4.jpg

[syborg tt]

Hard to tell but it's straight all the way down the side.
The bed is no longer wider then the truck.

http://www.syborgtwinturbo.com/albums/Build/2007_12_03_KD_5.jpg

One of the most important things I've noticed this week is the fact that
Kenny may have actually used the Tripod.

[ironworks]

Lookin good boys

[notorious1970]

Looking pretty awesome. Its going to look pretty sweet with paint on it!
-derek

[syborg tt]

Looking pretty awesome. Its going to look pretty sweet with paint on it!
-derek

Okay i have an idea - we both need to show up at a Local Cruise night together. Heck we can even ask my dad to drive his 57.

[kennyd]

Okay i have an idea - we both need to show up at a Local Cruise night together. Heck we can even ask my dad to drive his 57.


if he ever gets it back !

[syborg tt]

I know it's shocking but all of the pictures this week are clear

Wiper Cowl has been straightened to match the new Firewall

http://www.syborgtwinturbo.com/albums/Build/2007_12_09_0.jpg

Smoothing the Inner Fenders

http://www.syborgtwinturbo.com/albums/Build/2007_12_09_1.jpg

Both Sides - have to be perfect

http://www.syborgtwinturbo.com/albums/Build/2007_12_09_2.jpg

Teaser Shot of the Air Inlet -Tucked behind hit will be the Belle Intercooler

http://www.syborgtwinturbo.com/albums/Build/2007_12_09_3.jpg

[novanutcase]

SWWWEEEEEETTTT!!!

John

[Garage Dog 65]

Looking great !! Won't be long now. Any update on the motor build Marty ?

[syborg tt]

Looking great !! Won't be long now. Any update on the motor build Marty ?

Pretty sure the motor is complete. We were waiting on the pushrods and the incoorect one's came in and now we have the correct one's. I'll check and see if it's done yet.

[notorious1970]

Okay i have an idea - we both need to show up at a Local Cruise night together. Heck we can even ask my dad to drive his 57.

Okay ill one up you and say this..once we are into the nice weather we need to get your dads car, your truck, notorious and convince Troy to grab chicayne. That would be a cruise to remember!
-d

[65 347]

Okay ill one up you and say this..once we are into the nice weather we need to get your dads car, your truck, notorious and convince Troy to grab chicayne. That would be a cruise to remember!
-d
Sign me up for that cruise.:thumbsup:

[syborg tt]

Yep - you win

That would be a good time. Maybe Next year when I have the Great Lakes Gathering at my Shop we can convince him to bring it out.

Okay ill one up you and say this..once we are into the nice weather we need to get your dads car, your truck, notorious and convince Troy to grab chicayne. That would be a cruise to remember!
-d

[badmatt]

looking really good marty....

unfortunatly my trucks under a foot of snow rite now with no rear end under it.....

[Evil_s10]

Been following this build on here and s10forum.com and this has to be one of the best quality builds around. Keep up the awesome work. Getting this thing completed will be awesome to see!

[syborg tt]

Good Morning All,

Just a Quick Update.

I've been looking for a Solution for my Wilwood Brake pedal and I've found it.
The bonus is Shannon even offers a Matching Gas pedal.

Shannon Odom
(( [email protected] ))
www.modoinnovations.com

http://www.syborgtwinturbo.com/albums/Build/modo_innovations_640.jpg

Okay so here is what the Pedal looks like direct from Wilwood.


http://www.syborgtwinturbo.com/albums/Build/2006_10_21_003.jpg

Here are the pedals that I just received from Shannon.
Top notch piece - I'm really happy with the quality.


http://www.syborgtwinturbo.com/albums/Build/2007_12_19_002.jpg


http://www.syborgtwinturbo.com/albums/Build/2007_12_19_002.jpg

Okay so here is what they are going to look like.
PS - Thanks to the 2 J's for letting me steal this Picture.

http://www.syborgtwinturbo.com/albums/Build/pedalsafter_640.jpg

Have a Great Christmas everyone.

[tjbruning]

lookin' good! :thumbsup: :thumbsup: :thumbsup:

[syborg tt]

Okay I forgot to point this out.

Kenny filled the opening in the inner fender.

http://www.syborgtwinturbo.com/albums/Build/2007_12_03_KD_1.jpg

This is the finished inner fender

http://www.syborgtwinturbo.com/albums/Build/2007_12_09_2.jpg

okay now back to our regulary sceduled posting

[DG.]

Simply beautiful :thumbsup:

[BallnRods]

Syborg tt,
I was thumbing thru an old copy of Sport Truck Magazine & what do you know, I ran across an article on your build. Sorry I’m so late but congrats! I really enjoyed the read & it left me wanting more of your truck!

Benoit

[syborg tt]

Thank you very much - it sure has been fun building this truck and i can't wait to start the next project.

Syborg tt,
I was thumbing thru an old copy of Sport Truck Magazine & what do you know, I ran across an article on your build. Sorry I’m so late but congrats! I really enjoyed the read & it left me wanting more of your truck!

Benoit

[tjbruning]

Where's the 26's and half-cab body drop and dancing bed?




:lol:


Sweet build up for sure. My first vehicle was a Nissan Hardbody that was lowered on 50 series tires (before big wheels were available of course...).

I always wanted to buy a wrecked/rolled early 90's twin-turbo 300ZX and use the drivetrain & motor with the truck body & frame. I was 17 with no money, a dad who I could convince to help me, and time to day dream.....

Looking forward to seeing pictures of your dime on track day :thumbsup: