5 Years Later - It's Not a "new" Project, And Not a New Member Anymore!!!

[TravisB]

I vote for the very bottom one! :D

[syborg tt]

Well, looks like Dave got a bunch of work done this week.

There is a lot more room in the new dash housing then we thought.
I've got a bunch of playing with the dash to get it to look just like I want it but I like this one the most so far.

http://www.sportmachines.com/albums/p-bcab/2006_05_18_001.jpg

Side view doesn't look to busy does it.
I can't wait to send the dash to Tom at Hydro Illusions
(( www.hydroillusions.com )) to have him make it look like carbon fiber.
Did you notice the notch in the floor for the exhaust.

http://www.sportmachines.com/albums/p-bcab/2006_05_18_002.jpg

Now that we have the steering column back in.
Dave was able to complete the D-Side downpipe.
It has the same feel / flow as the P-Side.

http://www.sportmachines.com/albums/exhaust/2006_05_18_003.jpg

Just a quick shot of the downpipe and Mike Lee's Headers (( www.raceprovenmotors.com ))
Mike does some really nice work if your looking for a really good guy.

http://www.sportmachines.com/albums/exhaust/2006_05_18_004.jpg

[syborg tt]

It looks like the Master's are far away from the heat but we may make a heat shield just in case.
Did I mention that these are going to be swapped out for Billet one's?

http://www.sportmachines.com/albums/exhaust/2006_05_18_008.jpg

The exhaust is joined again for the last time on both sides.
Dave still has to run the wastegate dumps back into the downpipes.

http://www.sportmachines.com/albums/exhaust/2006_05_18_017.jpg

In order to gain the needed clearance around the intercooler
Dave reworked the lower portion of the core support.

http://www.sportmachines.com/albums/sogt0334cooling/2006_05_18_011.jpg

Trying to keep the same theme in the build. We did dual Rails similar to the back half.

http://www.sportmachines.com/albums/sogt0334cooling/2006_05_18_014.jpg

[syborg tt]

Here is my one of my favorite shots. Looking down into the engine bay.
I think it looks so much cleaner then before. We also gained the needed inner fender clearance.

http://www.sportmachines.com/albums/sogt0334eng-trans/2006_05_18_025.jpg

Before picture -- just in case you forgot.

http://www.sportmachines.com/albums/sogt0334eng-trans/2005_11_10_036.jpg

Okay I just thought it was a cool picture.
Cough - Cough MSD & Autometer sure would be nice sponsors on this project.

http://www.sportmachines.com/albums/finalpaint/2006_05_18_030.jpg

[syborg tt]

Just playing around again with camera angle's.

http://www.sportmachines.com/albums/finalpaint/2006_05_18_030.jpg

Wait -- Look up you can see the trans pan from Bowler Transmissions (( www.bowlertransmissions.com )).

Wow look at that MSD and Autometer again.......

http://www.sportmachines.com/albums/finalpaint/2006_05_18_042.jpg

That's it for this week more to come next week.

[Sales@Dutchboys]

Looking good!

-Paul :thumbsup:

[Beast2831]

Looking good! I would take the middle one out and move the fuel and tach closer together. would make it look cleaner. Looking real good!! I'm not a big truck guy, but I think it's gonna be killer! :thumbsup:

[syborg tt]

Looking good! I would take the middle one out and move the fuel and tach closer together. would make it look cleaner. Looking real good!! I'm not a big truck guy, but I think it's gonna be killer! :thumbsup:


Thank you. We thought about moving the tach to the center. but all of the other gauages are single sweep and the 4 in 1 has 4 dials. We weren't sure if it would look right with the 4 in 1 off to one side.

[black2002ls]

Looking good Marty.

[syborg tt]

Okay did a little more playing yesterday. I decided to recess the qauges a full 2" to get that OE look. I am thinking that the 3 larger quages are will be 1/2" off the panel and the smaller one's will be 1/4" off the panel.

What ya think ??

http://www.sportmachines.com/albums/p-bcab/2006_05_20_001.jpg

http://www.sportmachines.com/albums/p-bcab/2006_05_20_002.jpg

http://www.sportmachines.com/albums/p-bcab/2006_05_20_003.jpg

[black2002ls]

I like it

[syborg tt]

Good Morning All,

Meet with Bob Thrash today and talked about finishing the Rendering of the Interior.
I hope to have some new drawings in two weeks. He's busy painting graphics on the Cuda

http://www.sportmachines.com/albums/69-Baracuda/2006_05_26_001.jpg

Okay back to the regularly scheduled update

Here is the Final layout for the Dash.
I am flying down to Florida to meet with Doc at www.docskustom.com they are going to make me a billet panel to mount the gauges in. Those guy's down there have been a great help and i really look forward to working with them.

http://www.sportmachines.com/albums/p-bcab/2006_05_26_054.jpg

Here's the start of new Mount for the Front Support. We want to make the front cover easy to remove.

http://www.sportmachines.com/albums/chassis/2006_05_26_055.jpg

It will be slip shaft mounted so i can remove it when i need to get it on a trailer.

http://www.sportmachines.com/albums/chassis/2006_05_26_064.jpg

Okay don't freek out here - Yep it's a prototype front support (no Brackets)

http://www.sportmachines.com/albums/chassis/2006_05_26_066.jpg

[syborg tt]

Wastegates are plumbed back into the downpipes.

http://www.sportmachines.com/albums/exhaust/2006_05_26_059.jpg

http://www.sportmachines.com/albums/exhaust/2006_05_26_062.jpg

Just a quick shot to show how well thought out the Billet Specialties Serp Set up is. Note the A/C lines go down and away vs. straight out.

http://www.sportmachines.com/albums/exhaust/2006_05_26_070.jpg

Dave removed 1" of this pipe to make everything even up front.

http://www.sportmachines.com/albums/exhaust/2006_05_26_071.jpg

Okay here is the last picture of the wiper kit - this is where the shaft needs to come out. You can also see that we are going to fix the A pillar bodyline to match the fenders.

http://www.sportmachines.com/albums/p-bcab/2006_05_26_067.jpg


That's it for this week. Our goals this week is to get the entire exhaust welded. I should have at least one more update this week.

[black2002ls]

is that the 4 cylinder cuda that was in PHR this month being built by foose? if so....is it yours? loving the work on the truck. its coming together nicely

[Sales@Dutchboys]

The cuda being build was by troy..


-Paul

[syborg tt]

is that the 4 cylinder cuda that was in PHR this month being built by foose? if so....is it yours? loving the work on the truck. its coming together nicely


Not sure haven't read the latest issue of PHR - Nope not mine i couldn't afford the chassis on the car.

http://www.radrides.com/69cuda.html

Thanks for the compliment

[syborg tt]

Flew down to Florida to have my Billet Dash Panel made, this is the final layout.

http://www.docskustom.com/

Doc and Ron took care of me an they are hoping to have the panel complete so i can take it home with me.

http://www.syborgtwinturbo.com/albums/Highlights/2006_06_04_001.sized.jpg

PS - The Power Tour was a blast and Bob's Cuda is really incredible.

[kennyd]

marty,
going to troy's wed. night ? i got a call yesterday they needed some clips to assemble the cuda for the open house . i cant wait to see it painted .

[syborg tt]

marty,
going to troy's wed. night ? i got a call yesterday they needed some clips to assemble the cuda for the open house . i cant wait to see it painted .


Nope - going to the Magic Kingdom with the Kids still in Florida.

Just wait till you see the cuda

[kennyd]

Nope - going to the Magic Kingdom with the Kids still in Florida.

Just wait till you see the cuda

have a good time , i will probally be going there next year or two.

[syborg tt]

The Dash Surround is complete and i couldn't be happier.

I want to thank Doc one last time for taking such good care of me. As promised he stayed late and cranked out the dash overnight. I would of had pictures sooner but i was in the Magic Kingdom spending more money then should be allowed.

http://www.docskustom.com/images/docskustomlogolg.jpg

99 SOUTHLAND RD. ORMOND BEACH, FL 32174
386-676-9179 Phone ~ 386-677-6149 Fax

[email protected]

Here is the panel. When i get home and meet with Autometer will stuff some gauges in it so you can see how it looks.

http://www.syborgtwinturbo.com/albums/Build/2006_06_09_001.jpg

here is the back side view. You can see how the guages will be flush mounted from behind.

http://www.syborgtwinturbo.com/albums/Build/2006_06_09_002.jpg

here it is in the surround

http://www.syborgtwinturbo.com/albums/Build/2006_06_09_004.jpg

wait i almost forgot - Here is Doc taping the mounting bolts on the back.

http://www.syborgtwinturbo.com/albums/Build/2006_06_09_005.jpg

Once again - Doc Thanks for all of the help.

[black2002ls]

that peice looks amazing. I'm a fan of bezels out, but since most bezels are brushed aluminum, I don't guess they would be very noticeable. This is definately gonna have that factory look. Can't wait to see those guages in there!

[syborg tt]

Good Evening all,

Dave took a week off the truck to work on his Front Engine Dragster.
He finally broke into the 5's yes the 5's. He went 5.87 @ 25? mph at Route 66 Raceway in Joliet.
He is now one of the top 4 front engine guy's.

This weeks updates are all about the parts.
Ordered Axle's from Strange and as promised they shipped in 3 day's Great Company.

http://www.syborgtwinturbo.com/albums/Build/2006_06_14_004.jpg

Wait a new shaft -- Yep another steering shaft. The one from Syborg went into Project 663.

http://www.syborgtwinturbo.com/albums/Build/2006_06_14_007.jpg

Yet another throttle Cable - Lokar has sure made money off of me.

http://www.syborgtwinturbo.com/albums/Build/2006_06_14_006.jpg

New Gas Pedal - The picture doesn't do it justice, it's black!

http://www.syborgtwinturbo.com/albums/Build/2006_06_14_009.jpg

Hood Release Cable and pull

http://www.syborgtwinturbo.com/albums/Build/2006_06_14_012.jpg

[syborg tt]

This give's you an idea as to how the gauges are going to look in the new dash.

http://www.syborgtwinturbo.com/albums/Build/2006_06_14_013.jpg

Here it is in the truck -- it's amazing we were able to stick 9 Guages in there.

http://www.syborgtwinturbo.com/albums/Build/2006_06_14_020.jpg

That all for this week.
I didn't have time to get out there today to get pics of the work Dave did this week.
Next week I hope to have some really cool update as I plan to get it on the ground for the first time in over a year.

[Sales@Dutchboys]

Looking Good I like it!



-Paul

[syborg tt]

Good Afternoon,

Just a Quick Update.
Dave finished the dash surround just in time.

I meet Kris from Autometer at the shop to talk about the gauges that we want to put in the dash.
It looks like it's going to be the Sport Comp II line. Should look really nice once mounted.

http://www.syborgtwinturbo.com/albums/Build/3688_Speedo.jpg

This is the backside of the surround and how the billet panel mounts.

http://www.syborgtwinturbo.com/albums/Build/2006_06_21_002.jpg

Need to make room for the gauges and wiring

http://www.syborgtwinturbo.com/albums/Build/2006_06_21_018.jpg

This is how it looks in the truck with a spare set of Autometer Gauges

http://www.syborgtwinturbo.com/albums/Build/2006_06_21_005.jpg

It's hard to tell from the picture but this is one of there new Gauges in the panel.

http://www.syborgtwinturbo.com/albums/Build/2006_06_21_012.jpg

More to come on Saturday as i plan to work on it all day and have some help from Bob Thrash

[Sales@Dutchboys]

Love that dash ...good work...

-Paul

[syborg tt]

Love that dash ...good work...

-Paul

Thanks for the compliments

[Sales@Dutchboys]

When are you hoping to have it done?

-Paul

[syborg tt]

When are you hoping to have it done?
-Paul

I am hoping to have it at Rad Rides for Paint by the latest in October so i can make the Detroit Autorama in March.

Tommorow i plan to get the entire suspension and brakes back on the truck so Bob and i can play with inner fender design. He is going to help me to see if the inner fenders i want are even feasible. He is also going to do some rendering of both the underhood and interior/dash. This will be the first time the truck in on the ground in over a year. I can't wait to see how it looks

[Sales@Dutchboys]

Sweet man...I think Im are going to take my car the autorama too....My interior got in an aciedent and now my car wont get in their till august..

-Paul

[syborg tt]

I can't wait to see it. Do you have a project thread going ??

[Sales@Dutchboys]

Yea but its not updated ...Ill have pics tomorrow.....I got the fenders on today and the engine is ready to fire tomorrow or sunday...Then its ready for the interior shop.

-Paul

[syborg tt]

Never I repeat Never say the word "Fire" when your talking about a car it's a bad omen. Just kidding i bet you can't wait.

[Sales@Dutchboys]

lol...Yea I sure hope theres no fire. Can wait to hear it with open headers!

-Paul

[syborg tt]

Good Morning All,

It's on the Ground and i am pumped.
The ride height is dead on and it's low.

This is what the truck looked like when i arrived at 7:30am.
I have a bunch of work to do by 10am when Bob get's here.

http://www.syborgtwinturbo.com/albums/Build/2006_06_24_002.jpg

Fist thing to do was install the New 14" Rear Brakes from Precision Brakes.
They did a great job on the kit.
What's scarry is they no longer look big to me.

http://www.syborgtwinturbo.com/albums/Build/2006_06_24_004.jpg

Back View of the mounting brackets.

http://www.syborgtwinturbo.com/albums/Build/2006_06_24_005.jpg

The Brakes look better now that they are 14" vs. 13" that were originally on the truck.
www.precisionbrakescompany.com

http://www.syborgtwinturbo.com/albums/Build/2006_06_24_030.jpg

Installed the new Grille - looks much better then the White Mock Up Grille.

http://www.syborgtwinturbo.com/albums/Build/2006_06_24_011.jpg

[syborg tt]

This kinda of Gives you an Idea what Bob Thrash came up with for the Exhaust Exit.
More to come later i promise.

http://www.syborgtwinturbo.com/albums/Build/2006_06_24_029.jpg

Yep it was on the Ground by 10am and it's low. This is ride height so it can go 4" lower when aired out.

http://www.syborgtwinturbo.com/albums/Build/2006_06_24_016.jpg

You can see there is plenty of clearence to drive it on the road.

http://www.syborgtwinturbo.com/albums/Build/2006_06_24_019.jpg

Just your token rear end shot.

http://www.syborgtwinturbo.com/albums/Build/2006_06_24_020.jpg

Side View but that's pretty obvious

http://www.syborgtwinturbo.com/albums/Build/2006_06_24_024.jpg

[syborg tt]

I want to Thank Paul from Paul's Select for getting me my fiberglass front Cover for this Project.
The fit was perfect.
www.sportmachines.com/parts/cladding.php

http://www.syborgtwinturbo.com/albums/Build/2006_06_24_031.jpg

[Sales@Dutchboys]

Man I love it! Its just sick.


-Paul

[drmrman]

HELL YEAH! Now its coming together! Looks incredible man! Really great project! You guys do top notch work!

Joe

[syborg tt]

Thanks guy's - I'm just happy people are still looking at this thread.

[drmrman]

The only question I have is... Are those rotors on backwards... isnt the drilled and slotted grooves supposed to be facing the other way?

Joe

[black2002ls]

it looks awesome. Stance, wheels, everything. The front cover looks a little odd to me. But once its in paint I'm sure it will look great!!!

[syborg tt]

The only question I have is... Are those rotors on backwards... isnt the drilled and slotted grooves supposed to be facing the other way?

Joe


okay - so i wasn't paying attention when i put them on. Yep i was thrashing to get the entire suspension on in only 2 hours. My goal was to just get it on the ground and it looks like i cut some corners. The good news is that i put the calipers on in the correct orientation.

[syborg tt]

it looks awesome. Stance, wheels, everything. The front cover looks a little odd to me. But once its in paint I'm sure it will look great!!!

Thank you - yep the cover looks a little strange but it will look nice once it's painted

[drmrman]

okay - so i wasn't paying attention when i put them on. Yep i was thrashing to get the entire suspension on in only 2 hours. My goal was to just get it on the ground and it looks like i cut some corners. The good news is that i put the calipers on in the correct orientation.
OOOOH I see... I didnt mean to knit pick... HAHA! I was just wondering! :D

[syborg tt]

not a problem - it will help me pay more attention when i am putting the truck together for the final time

[kennyd]

marty , looks great . love the stance and wheels

[ironworks]

Lookin good.

I bet that thing will be a rocket ship.

Rodger

[GvEman]

Thats a inzane truck! ´But i lovet it! Awesome job man! We have one of those in sweden as well.. a Syclone twin turbo... It has ben dominating the dragstrip for years. Keep it up!

[syborg tt]

Thats a inzane truck! ´But i lovet it! Awesome job man! We have one of those in sweden as well.. a Syclone twin turbo... It has ben dominating the dragstrip for years. Keep it up!


Thank you - tell me about the one in sweeded i would love to see pics

[syborg tt]

Worked on the front bumper cover this weekend.

Had to modify the mounting tabs to work with a stock steel support.

Step one - Make sure you are wearing the proper safety glasses

http://www.syborgtwinturbo.com/albums/Build/2006_07_02_007.jpg

Step two - Carefully remove all of the mounting tabs

http://www.syborgtwinturbo.com/albums/Build/2006_07_02_004.jpg

Step Three - Take them to the grinder and reduce there size.
A long sleeve shirt may have prevented my forearms from itching so darn bad.

http://www.syborgtwinturbo.com/albums/Build/2006_07_02_008.jpg

Step Four - Glass all the tabs back on.

http://www.syborgtwinturbo.com/albums/Build/2006_07_02_011.jpg

Step Five - Drill the new holes

http://www.syborgtwinturbo.com/albums/Build/2006_07_04_006.jpg

[syborg tt]

Step Six - Run to local Sears and buy Stainless Steel bolts (did i mention i lost the original bolts)

http://www.syborgtwinturbo.com/albums/Build/2006_07_04_008.jpg

In the end it's mounted and it only took about 4 hours if you include the trip to Sears Hardware and the trips to the slop sink to wash my arms because they itched so badly.

[Sales@Dutchboys]

FUN STUFF!!!!!

-Paul

[black2002ls]

dont you love 'glass! lol. Great work.

[XcYZ]

Step Six - Run to local Sears and buy Stainless Steel bolts (did i mention i lost the original bolts)

Don't you just love that. lol

Looks great, Marty! :thumbsup:

[syborg tt]

Don't you just love that. lol

Looks great, Marty! :thumbsup:


I spent about two hours cleaning my garage shop in order to bring more parts home so when the time comes to test fit everything it's all in one place.

What really sucks is i started cleaning because i can't find any of my tailgate hardware that i bought and without the hardware i can't install the relocate handle.

[syborg tt]

Happy Sunday,

Dave was able to squeeze in a bunch of work this week.
He was able to get both front and rear bumpers mounted.
He came up with a pretty cool way to mount the bumpers and make adjust much easier.

Here is the mount for the front cover

http://www.syborgtwinturbo.com/albums/Build/2006_07_22_003.jpg

Plenty of adjustment up down so we should be able to nail the alignment perfectly.

http://www.syborgtwinturbo.com/albums/Build/2006_07_22_006.jpg

Finished Product

http://www.syborgtwinturbo.com/albums/Build/2006_07_22_028.jpg

Since were on the front end - Dave Finished the steering shaft.

http://www.syborgtwinturbo.com/albums/Build/2006_07_22_029.jpg

[syborg tt]

Moving back to the rear end.
This is the beginning of the rear bumper mounting.

http://www.syborgtwinturbo.com/albums/Build/2006_07_22_007.jpg

Plenty of adjustments with this mount

http://www.syborgtwinturbo.com/albums/Build/2006_07_22_008.jpg

Just a quick side view

http://www.syborgtwinturbo.com/albums/Build/2006_07_22_009.jpg

Dave mounted the engine oil cooler on the Drivers Side.

http://www.syborgtwinturbo.com/albums/Build/2006_07_22_012.jpg

[syborg tt]

Okay rear cover view.

http://www.syborgtwinturbo.com/albums/Build/2006_07_22_016.jpg

Here are the plans for the end of the truck.
Remake the rear cover out of steel and incorporate the rear belly pan

http://www.syborgtwinturbo.com/albums/Build/2006_07_22_018.jpg

underside view.

http://www.syborgtwinturbo.com/albums/Build/2006_07_22_019.jpg

[syborg tt]

Had some extra time today so i decided to roll the inner fender lip.

http://www.syborgtwinturbo.com/albums/Build/2006_07_22_023.jpg

Action Shot

http://www.syborgtwinturbo.com/albums/Build/2006_07_22_022.jpg

Really bad picture - but you get the idea.

http://www.syborgtwinturbo.com/albums/Build/2006_07_22_021.jpg

That's it for this week.

[Payton King]

where did you get it?

[black2002ls]

Looking great!! its all starting to come together

[syborg tt]

Happy Monday all,

Okay skipped last week here Dad bought a new project
and it's eating up what's left of my spare time and it's not even here yet.

more pictures here
http://www.sportmachines.com/gallery/57-Chevy

http://www.sportmachines.com/albums/57-Chevy/Ebay_Status_2.jpg

Should be a fun little Project

http://www.sportmachines.com/albums/57-Chevy/Ebay_Status_12.jpg

Okay back to my project which doesn't seem as cool anymore
Dave was able to bend up a test panel of the rear bumper

http://www.syborgtwinturbo.com/albums/Build/2006_08_02_003.jpg

Started working on the Fuel System.
Located the FPR in the Intake Valley to keep it clean looking

http://www.syborgtwinturbo.com/albums/Build/2006_07_26_056.jpg

Fuel Line coming out of the Tank

http://www.syborgtwinturbo.com/albums/Build/2006_08_04_001.jpg

[syborg tt]

Into the Aeromotive 100 Micron Filer & A1000 Pump

http://www.syborgtwinturbo.com/albums/Build/2006_08_04_007.jpg

The second filter is the 10 Micron Filter just to get out the really small stuff

http://www.syborgtwinturbo.com/albums/Build/2006_08_04_009.jpg

Mounted a Bulkhead at the back of the Cab so we can remove the cab
and not have to worry about the lines that are mounted to the frame.

http://www.syborgtwinturbo.com/albums/Build/2006_08_04_010.jpg

Just a quick look up at the underside

http://www.syborgtwinturbo.com/albums/Build/2006_08_04_013.jpg

That's all for this week.
I may have to take a week off so we can figure out where the 57 Chevy is going.
Just need to figure out who,where and when. My Choice are Kenny Davis Hot Rods, Pinkee's or Rad Rides.

[black2002ls]

the truck is looking good! the new project is quite interesting as well!

[T Bell]

pontiac heads?

[syborg tt]

pontiac heads?

yep they are Pontiac Racing Heads for a v6. They were used in IMSA racing and some other venue's. Lately everyone that is building a v6 wants them.

[T Bell]

and you are building a turbo'd 4.3 right? I didn't know those heads fit. Learn something new everyday.

[syborg tt]

and you are building a turbo'd 4.3 right? I didn't know those heads fit. Learn something new everyday.

yep turbo 4.3 with a GM Racing Bowtie Block

[syborg tt]

Good Morning All,

There is going to be two updates this week as i plan to work all day Saturday on the truck

Wanted to do something different for a steering Stop.
Dave came up with a pretty cool idea don't ya think.

http://www.syborgtwinturbo.com/albums/Build/2006_08_17_028.jpg

Just some Quick Picks of the Intercooler Piping

http://www.syborgtwinturbo.com/albums/Build/2006_08_17_030.jpg

All the Hose, V-Bands and Connections were supplied by Jim at:

www.hightempsilicone.com

He makes some really nice stuff and it's not the cheap stuff you find on Ebay.

http://www.syborgtwinturbo.com/albums/Build/2006_08_17_031.jpg

You can also see the Intercooler which was custom built by Gerhard at:
www.bellintercoolers.com

Turn around time was less then a week and the Quality is top notch

http://www.syborgtwinturbo.com/albums/Build/2006_08_17_032.jpg

[syborg tt]

Just another Quick Shot of all the Stainless Piping from:
www.stainlessworks.net

http://www.syborgtwinturbo.com/albums/Build/2006_08_17_033.jpg

Need to Create the Inner Fenders & Air Boxes this weekend

http://www.syborgtwinturbo.com/albums/Build/2006_08_17_034.jpg

Your not going to believe it i found an Upper Radiator Hose that Works
Now if i could just find a lower hose

http://www.syborgtwinturbo.com/albums/Build/2006_08_17_035.jpg

Just a quick shot of the Rear Suspension Stop.
I still need to pay Troy for this.

http://www.syborgtwinturbo.com/albums/Build/2006_08_17_036.jpg

That's all for today more to come over the weekend

[black2002ls]

Looking good Marty. Any idea how much longer before its drivable?

[syborg tt]

Looking good Marty. Any idea how much longer before its drivable?

The second Tuesday of Next Week.

Actually my goal has been the Detroit Autorama in 07 and yes my fingers are really really crossed

[syborg tt]

Happy Saturday Night,

What started out as a very productive day didn't end so well.
Just remember Listen to the Voices in your Head they are there for a Reason!

Yep, found a Lower Radiator Hose that actual works.
It's hard to believe it actual follows the curves of the Frame.

http://www.syborgtwinturbo.com/albums/Build/2006_08_19_001.jpg

Installed the new Fiberglass Cladding.

http://www.syborgtwinturbo.com/albums/Build/2006_08_19_002.jpg

If you are thinking about adding really cool ground effects to your s10.
You need to contact Scott @ www.syclone-typhoon.com

http://www.syborgtwinturbo.com/albums/Build/2006_08_19_004.jpg

Yep missing the last piece of cladding this is where my day ended.
Seems I felt the necessary urge to run a 1/4" drill bit 1" deep into the pad of my left Hand.

http://www.syborgtwinturbo.com/albums/Build/2006_08_19_005.jpg

So my day ended early with a trip to the emergency room to make sure I
didn't have any metal in my hand and a tetanus shot just in case.

More to come later in the week once I can use my hand again.
And remember when the little voice tells you that you should move your hand - Listen!

[black2002ls]

Looking good. Bummer about the hand. Best of luck in the healing process!

[syborg tt]

Looking good. Bummer about the hand. Best of luck in the healing process!

Man i forgot how bad a tetnus shot feels for the next couple day's after.

[syborg tt]

Happy Wednesday Night.

Stop by the shop to play with some inner fender design and look at the air box.

http://www.syborgtwinturbo.com/albums/Build/2006_08_23_055.jpg

Hard to tell from the picture but we are going to draw air in from the the indicators.

http://www.syborgtwinturbo.com/albums/Build/2006_08_23_056.jpg

This gives you an idea of the arc were trying to fit acheive in the inner fenders

http://www.syborgtwinturbo.com/albums/Build/2006_08_23_051.jpg

Side View

http://www.syborgtwinturbo.com/albums/Build/2006_08_23_057.jpg

Looking for Opinions

http://www.syborgtwinturbo.com/albums/Build/2006_08_23_058.jpg

more to come this weekend
- and yes i am going to stay away from power tools this weekend

[kennyd]

looks great marty , i like these inner fenders better , just cove them by the turbo .

[XcYZ]

Cool, looks amazing Marty. :thumbsup:

[syborg tt]

thanks guys

[syborg tt]

Well, it was another Good Day - No blood or trips to the Hospital.

I was able to get the last piece of Cladding on the truck without hurting myself and I used the drill.

http://www.syborgtwinturbo.com/albums/Build/2006_08_26_001.jpg

Finished all of the fittings for the Fuel System

http://www.syborgtwinturbo.com/albums/Build/2006_08_26_004.jpg

Jared was Kind enough to send me some Kick Panel Speaker Pods.
I'm going to have to build something similar with a smaller speaker to clear the roll bar.

http://www.syborgtwinturbo.com/albums/Build/2006_08_26_007.jpg

You can kind of get an idea of what i am going for

http://www.syborgtwinturbo.com/albums/Build/2006_08_26_010.jpg

Hard to tell from the side but this will have rounded or rolled sides

http://www.syborgtwinturbo.com/albums/Build/2006_08_26_011.jpg

[syborg tt]

Quick shot of the drivers side leaving the turbo

http://www.syborgtwinturbo.com/albums/Build/2006_08_26_014.jpg

The drivers side has more of a Curve in it & i think it looks better - Opinions

http://www.syborgtwinturbo.com/albums/Build/2006_08_26_016.jpg

That's all for this week

[black2002ls]

lookin good marty. Its coming along nicely

[kennyd]

do you think that cardboard will take paint easy ?

[syborg tt]

do you think that cardboard will take paint easy ?

actually it's chipboard with a varnish so it should hold up pretty good

[customcam]

Im late to say anything but iv been folowing your build and im like :wow:
amazing stuff marty every inch uv done perfectly :thumbsup:
the passenger side roll looks like theres more space in the bay > they both look good ;)

[syborg tt]

I think you should stay away from cutting around the turbos.
Keep the inner fenders under the turbos awith some clearance.
That way the inner fenders won't get so hot and it will give you clearence to work on the engine if you need to and it lets you see more of the engine.
Just my .02 cents

Long week and even a Longer Weekend.
Hung out at the waterpark with the kids and swallowed more chlorine then I want to admit.

Last week Robert from the Pro-Touring Forum made a suggestion.
So I took his advice and built yet another set of inner fenders.
He was right it cleaned up the engine bay and will make life much easier if I ever have to work on this thing.

http://www.syborgtwinturbo.com/albums/Build/2006_09_02_004.jpg

http://www.syborgtwinturbo.com/albums/Build/2006_09_02_005.jpg

http://www.syborgtwinturbo.com/albums/Build/2006_09_02_010.jpg

I was able to get the rear bumper mounted.
We are going to have to pie cut the rear corner cladding to make it fit better.

http://www.syborgtwinturbo.com/albums/Build/2006_09_02_001.jpg

Mounted the Tailgate with the second set of hinges (Genuine GM) and the tailgate doesn't fit any better then it did with the LMC Truck Hinges that were a 4th the price.

http://www.syborgtwinturbo.com/albums/Build/2006_09_02_003.jpg

[syborg tt]

Dusted some paint on the radiator cover.

http://www.syborgtwinturbo.com/albums/Build/2006_09_02_013.jpg

That's all for this week.

[black2002ls]

looking good marty

[syborg tt]

Going back to the original concept of the truck being a Factory Prototype - these make more sense.

here is where i got the idea from.

http://www.sportmachines.com/albums/misc/2006_01_29_106.jpg

http://www.sportmachines.com/albums/misc/2006_01_29_107.jpg

http://www.sportmachines.com/albums/misc/2006_02_09_005.jpg

http://www.sportmachines.com/albums/misc/2006_02_09_007.jpg

[Tim Baillie]

do you have any more pics of that Buick ? High Res ?

[syborg tt]

do you have any more pics of that Buick ? High Res ?

did a little searching and found it

http://www.gmhightechperformance.com/features/0503htp_1987_buick_turbo_regal_feature/

[syborg tt]

I would like to Thank Flaming Rivers for looking at my Project and offer to Sponsor us.

You can visit them at http://www.flamingriver.com/

http://www.syborgtwinturbo.com/albums/Renderings/flaming_River.jpg

Steve was kind enough to recommend the right steering box for my project.

The ratio is 14 to 1 which is more then I'll ever use on the Power Tour

http://www.syborgtwinturbo.com/albums/Build/2006_09_07_002.jpg

http://www.syborgtwinturbo.com/albums/Build/2006_09_07_003.jpg

That's all for this week as I didn't have time to work on the truck this week.
The good news is Dave worked on it for me.

[syborg tt]

Good Day to All,

Stopped by the Shop with my Dad last night he wanted to see the truck in person instead of pictures.
He said looks good just don't tell your wife how much you've spent.

I installed the new Flaming Rivers Steering Box and let me say it was on in 10 minutes.
It's nice having compatible parts. Everything fit perfect.

http://www.syborgtwinturbo.com/albums/Build/2006_09_14_001.jpg

The Bed Floor is almost complete should be ready to go to the body guy in 2 weeks

http://www.syborgtwinturbo.com/albums/Build/2006_09_14_002.jpg

We closed up the back panels - just to clean it up a little

http://www.syborgtwinturbo.com/albums/Build/2006_09_14_003.jpg

We needed to add a little metal to the back corners so we mount the cladding.

http://www.syborgtwinturbo.com/albums/Build/2006_09_14_006.jpg

This is the last Panel needed to be completed. Then the bed is done

http://www.syborgtwinturbo.com/albums/Build/2006_09_14_005.jpg

[syborg tt]

Good Day All,

I headed over to VFN Fiberglass on Saturday to look at the Mold that they made for the Rockers.

www.vfnfiberglass.com

http://www.syborgtwinturbo.com/albums/Build/2006_09_16_001.jpg

We added a 1/4" to each side of the Rocker so they would actually be long enough.
From the Factory they were about a 1/2" shy and since we are making everything else so nice we might as well fix this.

http://www.syborgtwinturbo.com/albums/Build/2006_09_16_003.jpg

[ProTouring442]

VFN, eh? I hope you have better luck with their stuff then I did! I've seen fewer air bubbles in a glass of Alka-Seltzer.

Shiny Side Up!
Bill
'72 442 "Inamorata"

[syborg tt]

VFN, eh? I hope you have better luch with their stuff then I did! I've seen fewer air bubbles in a glass og Alka-Seltzer.

Shiny Side Up!
Bill
'72 442 "Inamorata"

I heard this before. I looked at alot of there piece and they look nice. I know they have tried to change that image and have worked very hard to clean up there stuff. The good news is they are only 15 minutes from my house so i can easily check on there progress.

[JayR]

did a little searching and found it

http://www.gmhightechperformance.com/features/0503htp_1987_buick_turbo_regal_feature/

As nasty as that Buick must be hanging the front tires on the track, how sick would it be hammered down on a set of 19" H.R.E.s with some big huge brakes and the underpinnings to drive it in anger around some corners. Just keep it off full boost in the apexes!

Oh, and the truck is BAD TO THE BONE, Marty. Amazing job and thanks for the updates. You give us something to aspire to.

[ProTouring442]

I heard this before. I looked at alot of there piece and they look nice. I know they have tried to change that image and have worked very hard to clean up there stuff. The good news is they are only 15 minutes from my house so i can easily check on there progress.


Hmmm.... too bad they didn't do this a few years ago! :rolleyes: Ahh well, maybe I'll call on them to make molds of my current bumpers if I ever need new ones. Assuming you have good luck! Please let us know how this goes.

Shiny Side Up!
Bill
'72 442 "Inamorata"

[syborg tt]

As nasty as that Buick must be hanging the front tires on the track, how sick would it be hammered down on a set of 19" H.R.E.s with some big huge brakes and the underpinnings to drive it in anger around some corners. Just keep it off full boost in the apexes!

Yep that Buick is nasty. A buddy of mine built a set of inner fenders like this for his monty and they just look sick.

Oh, and the truck is BAD TO THE BONE, Marty. Amazing job and thanks for the updates. You give us something to aspire to.

Jason, all i can say is thank you. When you say my project is amazing i'm shocked because it's guy's like you that gave me the inspiration and the idea's. I've looked at your renderings over and over trying to learn from you. Once again Thank you for the compliments.

[syborg tt]

Hmmm.... too bad they didn't do this a few years ago! :rolleyes: Ahh well, maybe I'll call on them to make molds of my current bumpers if I ever need new ones. Assuming you have good luck! Please let us know how this goes.

Shiny Side Up!
Bill
'72 442 "Inamorata"

I can tell you that there mold work is outstanding. I've had some molds made at other shops and let's just say there molds are much better.

[black2002ls]

I love Mondays. I fiend for a week for updates on this, and come Monday it is finally satisfied. Amazing work as usual

[syborg tt]

I love Mondays. I fiend for a week for updates on this, and come Monday it is finally satisfied. Amazing work as usual

thank you very much

[JayR]

Jason, all i can say is thank you. When you say my project is amazing i'm shocked because it's guy's like you that gave me the inspiration and the idea's. I've looked at your renderings over and over trying to learn from you. Once again Thank you for the compliments.

Thanks Marty, I'm blushing! But seriously, My mouth hangs open every time I check your progress page. Good job and I can't wait to see what you guys do to the 57.

[syborg tt]

Thanks Marty, I'm blushing! But seriously, My mouth hangs open every time I check your progress page. Good job and I can't wait to see what you guys do to the 57.

Man it's not often i make a guy blush.

Good news is the 57 is on it's way to Kenny as we speak. I can't wait to see how it turns out.

[x-tream]

i just finnished going through all 36 pages of progress so far. all i can say is damn there is a lot of fabrication into that truck. You should make your own build book for that truck.

One question, were did you get you black braded hose and black fittings??, those are bad ass.

[ProTouring442]

One question, were did you get you black braded hose and black fittings??, those are bad ass.


Summit has them... called something-lite or some such. Easy to work with too, I'm using it on my car. It has a cloth braid so it won't tear up anything it comes in contact with.

Shiny Side Up!
Bill
'72 442 "Inamorata"

[syborg tt]

i just finnished going through all 36 pages of progress so far. all i can say is damn there is a lot of fabrication into that truck. You should make your own build book for that truck.

Thank you very Much. Shoot me an e-mail and i'll send you the rough draft of the build book. So yep there will be a build book however it may be in PDF form.

One question, were did you get you black braded hose and black fittings??, those are bad ass.

Yep - it's Pro-Lite Hose from Earl

[Tim Baillie]

Thank you very Much. Shoot me an e-mail and i'll send you the rough draft of the build book. So yep there will be a build book however it may be in PDF form.


[email protected] :D

[syborg tt]

[email protected] :D

e-mail sent

[syborg tt]

Okay a post before the actual update -- what do you guy's think?

These are courtesy of my wife camera skills.

http://www.syborgtwinturbo.com/albums/Highlights/2006_09_23_r_262.jpg

http://www.syborgtwinturbo.com/albums/Highlights/2006_09_23_r_271.jpg

[hiwayman]

yeah man that is cool you have got too be smiling

[ProTouring442]

That's super! Makes you feel great when it starts to look like a vehicle again, doesn't it!

Shiny Side Up!
Bill
'72 442 "Inamorata"

[SpeedRacer]

Coming together nicely :thumbsup:

Those brakes look incredible behind those rims... Size does matter :unibrow:

[syborg tt]

yep it is really cool to see it on the ground and man does it feel good to actually see what it looks like outside of the shop.

love the comment about size does matter

[BLUE'03]

Wow.Looks great.I've been following your build and bet your really excited to see it on the ground.Getting ready to start on my '92 s10...It won't be as cool as yours but it's inspirational.

[syborg tt]

Wow.Looks great.I've been following your build and bet your really excited to see it on the ground.Getting ready to start on my '92 s10...It won't be as cool as yours but it's inspirational.


man i was stoked when we pushed it outside and i got to see how it looked. It was just way to cool.

send me the link to yours when you start it so i don't miss it.

[syborg tt]

here is another one that i think is cool

http://www.syborgtwinturbo.com/albums/Highlights/2006_09_23_r_338.jpg

[BLUE'03]

That is a cool picture.You'll be the first to know when i start because i'll have a bunch of questions before hand.Did you get my e-mail?

[syborg tt]

That is a cool picture.You'll be the first to know when i start because i'll have a bunch of questions before hand.Did you get my e-mail?


thank you - yep answering your questions as we speak

[syborg tt]

Okay i almost forgot that I have an Update been a busy week.

Picked up the Doors from Rad Rides.
Levi worked his magic and shaved the handles & locks

http://www.syborgtwinturbo.com/albums/Build/2006_09_22_003.jpg

Picked up the finished rocker cladding from VFN Fiberglass

http://www.syborgtwinturbo.com/albums/Build/2006_09_22_004.jpg

okay last pic - just a cool pic

http://www.syborgtwinturbo.com/albums/Build/2006_09_23_r_66.jpg

[black2002ls]

lookin good!!

[syborg tt]

Good Morning All,

Dave and I came up with an idea of a Removable Tie Down.
We wanted something that could be removed during a show or while driving on the street.
Once the frame is painted you won't even notice it.

http://www.syborgtwinturbo.com/albums/Build/2006_09_28_001.jpg

Dave began working on the air inlet ducts.
We plan to draw air in from the factory driving lights.

http://www.syborgtwinturbo.com/albums/Build/2006_09_28_003.jpg

We going to extend the wheel well to complete the inner fender

http://www.syborgtwinturbo.com/albums/Build/2006_09_28_010.jpg

Dave started working on the belly pan for the rear.
The strings gives you an idea of what the center will look at.

http://www.syborgtwinturbo.com/albums/Build/2006_09_28_011.jpg

Just a rear view
It actually looks like the center is lower then the end panels it's not - just an illusion

http://www.syborgtwinturbo.com/albums/Build/2006_09_28_006.jpg

More to come next week.

[black2002ls]

Monday sweet Monday. Jonesin for a fix and you deliver!! Looking good Marty

[syborg tt]

Monday sweet Monday. Jonesin for a fix and you deliver!! Looking good Marty

I was almost going to post these on Friday and then because of a previous post i decided to wait till monday. I did however spend about 4 hours at Rad Rides on Saturday took so really cool pics of the biscayne and worked on the rendering for both of our cars.

[drmrman]

WOW! I have been checking up on this build every couple weeks... And all I can say is that I have the up-most respect for you and all the guys working on this truck! Your work is so clean! You all are so tallented!

I know its not finished but congrats on putting together one of the cleanest mini's Ive seen in a long time!

Joe

[syborg tt]

WOW! I have been checking up on this build every couple weeks... And all I can say is that I have the up-most respect for you and all the guys working on this truck! Your work is so clean! You all are so tallented!

I know its not finished but congrats on putting together one of the cleanest mini's Ive seen in a long time!

Joe

I have learned so much just by looking at other cars being built. This forum and a few otheres have inspired me to build the best that i can afford without my wife killing me. I've learned more about building cars then i thought was possible.

Thanks again

[lower90xcab]

http://www.syborgtwinturbo.com/albums/Build/2006_09_28_001.jpg

http://www.syborgtwinturbo.com/albums/Build/2006_09_28_003.jpg


Are those Belltech sway bars or are they another aftermarket sway bar? I have the ZQ8's on my truck now and Im looking for something a little better.

thanks
lower90

[syborg tt]

Yep Bell Tech Bar - I have one on my other GT and it handles a little better. However it sits just a little lower

Are those Belltech sway bars or are they another aftermarket sway bar? I have the ZQ8's on my truck now and Im looking for something a little better.
thanks
lower90

[syborg tt]

Happy Monday Morning.

Big Updates this week looks like I am going to split this update into multiple e-mails.

Starting with the bed.
The rear belly pan is almost complete.

http://www.syborgtwinturbo.com/albums/Build/2006_10_07_014.jpg

2nd shot - show's off the air ride tank and hardware

http://www.syborgtwinturbo.com/albums/Build/2006_10_07_016.jpg

Side View

http://www.syborgtwinturbo.com/albums/Build/2006_10_07_017.jpg

This is what the back side of the wheel well looks like.

http://www.syborgtwinturbo.com/albums/Build/2006_10_07_018.jpg

Looking back from the inside of the wheel well

http://www.syborgtwinturbo.com/albums/Build/2006_10_07_019.jpg

[syborg tt]

This is what we are planning to do the front of the wheel well.

http://www.syborgtwinturbo.com/albums/Build/2006_10_07_022.jpg

This is what it would look like if we didn't modify it.

http://www.syborgtwinturbo.com/albums/Build/2006_10_07_027.jpg

Dave finally trimmed the inner fender to expose the frame.

http://www.syborgtwinturbo.com/albums/Build/2006_10_07_024.jpg

More to come in another e-mail.

[syborg tt]

Okay like I said Dave accomplished a bunch of work this week.

Air goes in the driving light.

http://www.syborgtwinturbo.com/albums/Build/2006_10_07_005.jpg

Curves up to the Airbox.

http://www.syborgtwinturbo.com/albums/Build/2006_10_07_006.jpg

Here is where it meets the Airbox.

http://www.syborgtwinturbo.com/albums/Build/2006_10_07_007.jpg

Yet another little detail that needs to addressed

http://www.syborgtwinturbo.com/albums/Build/2006_10_07_013.jpg

Where going to extend the inner fender to cover the mounting hardware for the GT's Cladding.

http://www.syborgtwinturbo.com/albums/Build/2006_10_07_012.jpg

[syborg tt]

While were at the front of the truck.
We finally found a suitable location for the overflow bottle behind the core support.
Yep it's a scary home but it works.

http://www.syborgtwinturbo.com/albums/Build/2006_10_07_028.jpg

Yep it's tight in there but we can still view the tank from above.

http://www.syborgtwinturbo.com/albums/Build/2006_10_07_029.jpg

one more post and i'm going to bed

[syborg tt]

Okay like I said Dave did a bunch this week.

However i actually did this update.

First I want to Thank Caleb Davis for locating a Supplier on a Saturday
that would have a smooth tailgate in stock and willing to wait for me to pick it up.

http://www.syborgtwinturbo.com/albums/Build/2006_10_07_032.jpg

Okay time to cut it up and install the handle relocate kit from LMC Truck.
PS - man is this a nice kit.

http://www.syborgtwinturbo.com/albums/Build/2006_10_07_034.jpg

Back View

http://www.syborgtwinturbo.com/albums/Build/2006_10_07_035.jpg

First Cut the Opening.

http://www.syborgtwinturbo.com/albums/Build/2006_10_07_041.jpg

Next Drill 14 holes without drilling into your hand.
Mount relocated handle.

http://www.syborgtwinturbo.com/albums/Build/2006_10_07_042.jpg

Really that's it for this week.

[lower90xcab]

Yep Bell Tech Bar - I have one on my other GT and it handles a little better. However it sits just a little lower


How much bigger are the belltechs vs the zq8 sway bars? Would I see much improvement over the zq8? Also my truck is dropped 5/6.

[syborg tt]

How much bigger are the belltechs vs the zq8 sway bars? Would I see much improvement over the zq8? Also my truck is dropped 5/6.

couldn't tell you for sure. I can measure mine and see if you can find a zq8 truck. I know that some of the guy's on S-Series have swapped out for the bell techs.

[lower90xcab]

couldn't tell you for sure. I can measure mine and see if you can find a zq8 truck. I know that some of the guy's on S-Series have swapped out for the bell techs.


Can you please measure them for me? thanks!!!

[black2002ls]

Very nice!!! as always. I couldn't find the thread in the usual forum and I was like :willy:

[syborg tt]

Very nice!!! as always. I couldn't find the thread in the usual forum and I was like :willy:


yep it was moved last week. Just trying to keep everyone on there toes

[syborg tt]

Good Morning All,

Last Week sure was a busy one.
Headed down to Ar Kansas to see the progress on Dad's 57.
Check out the link.
http://www.lateral-g.net/forums/showthread.php4?t=5538


Dave was able to complete most of the tin work for the Bed.
Without this piece it would have looked incomplete.

http://www.syborgtwinturbo.com/albums/Build/2006_10_14_018.jpg

View from the underside.
This was a tough picture to take since it was sitting on the floor.

http://www.syborgtwinturbo.com/albums/Build/2006_10_14_015.jpg

Mounted the charcoal canister.
I don't want my garage to smell like fuel.

http://www.syborgtwinturbo.com/albums/Build/2006_10_14_008.jpg

[syborg tt]

Instead of making the bracket simple.
Dave took the time to make it pretty and simple.

http://www.syborgtwinturbo.com/albums/Build/2006_10_14_012.jpg

The linkage is all hooked back up.

http://www.syborgtwinturbo.com/albums/Build/2006_10_14_005.jpg

You can see the bell crank that we are using to change the pull.

http://www.syborgtwinturbo.com/albums/Build/2006_10_14_001.jpg

Cable come out parallel to the manifold.
Still one more bracket to make on the Manifold
and one on the firewall.

http://www.syborgtwinturbo.com/albums/Build/2006_10_14_007.jpg

[syborg tt]

Just a Quick look through the Back Wheel

http://www.syborgtwinturbo.com/albums/Build/2006_10_14_020.jpg

Have to keep the family involved.
We had my daughter tape up the Billet Specialties Column.

http://www.syborgtwinturbo.com/albums/Build/2006_10_14_028.jpg

We are trying to lay out the gauges and switches.
Also include will be a Cig lighter for the needed Radar Detector.

http://www.syborgtwinturbo.com/albums/Build/2006_10_14_023.jpg

Just a design layout for the Dash. Nothing is set in stone.
We are going to wait to see what Bob Thrash comes up with.

http://www.syborgtwinturbo.com/albums/Build/2006_10_14_025.jpg

[syborg tt]

Found a suitable location for the American Auto Wire Highway 22 Harness.
This is a very nice kit indeed. Can't wait to wire it.

http://www.syborgtwinturbo.com/albums/Build/2006_10_14_030.jpg

Also found the location for the MSD box. But forgot to take the picture.

http://www.syborgtwinturbo.com/albums/Build/2006_10_14_031.jpg

I quess your going to have to wait till next week to see where we mount that.

[black2002ls]

looking good marty. :thumbsup:

[Mike Hall]

I love the giant scale bellcrank throttle cable setup. LOL

Mike

[syborg tt]

Quick Update.

I flew down to Ar-Kansas over the weekend to meet with Kenny & the guy's at Kenny Davis Hot Rods. I have a little medical problem which is going to delay the build. Seems the Doctors feel it's important for them to remove the tumor in my neck something about cancer. Which means this is going to delay the truck by 4 weeks which puts it ready for paint in Late December. This is about the time the Riddler car will be ready for paint and bodywork at Troy's. So my truck would be delayed by at least two months waiting to get into Rad Rides body shop. So I needed to find a painter that is comprable in my eye's. Thus the reason I choose Kenny, I feel like this is going to be a very good Match.

The main reason I don't want to delay the truck by another 2 months is i want to make sure it's ready for Hvaoc in 07 and i actually make it to Sema in 07.

3 weeks from today i'll be in surgery and the bad news is i won't be able to talk for 3 day's - EAK !! and if you know me this is going to be very hard for me. My wife told me she is looking forward to the peace and quiet.

[AAW]

Take care of you first Marty! The Truck comes later. Good luck and I wish you a speedy recovery.

[XcYZ]

Good luck, Marty. Hope all goes well and you have a speedy recovery.

[Budweasel]

Marty, take care of yourself. Best wishes for a speedy recovery.

[syborg tt]

Thanks for thinking of me everyone.

[black2002ls]

got you in my thoughts and prayers!

[J2SpeedandCustom]

Hope everything goes well Marty! I really enjoy the updates and progress pics. :thumbsup:

[BLUE'03]

Marty,I hope everthing goes well.Take care of yourself first,the truck will be there.

[syborg tt]

Good Morning,

Dave worked on the Dash this week. It's starting to look like a dash again.

First - mounted behind the dash is the Highway 22 Fuse Box.

http://www.syborgtwinturbo.com/albums/Build/2006_10_21_001.jpg

You can see the Vent mounted on the Passenger Side of the truck.
We are still going to install one more vent for the Passenger highlighted in black.

http://www.syborgtwinturbo.com/albums/Build/2006_10_21_005e.jpg

Here is a close up of the Drivers Side.
All of the switches have been reverse mounted. The goal is to keep the dash ultra smooth.

http://www.syborgtwinturbo.com/albums/Build/2006_10_21_003.jpg

This is what the backside looks like.

http://www.syborgtwinturbo.com/albums/Build/2006_10_21_010.jpg

Dave had to change the way we mounted the dash so the hardware wasn't visible.

http://www.syborgtwinturbo.com/albums/Build/2006_10_21_006.jpg

[syborg tt]

The MSD box is mounted in it's new home.

http://www.syborgtwinturbo.com/albums/Build/2006_10_21_007.jpg

One of the members on syty.net sent this trick piece.
http://www.syty.net/forums/showthread.php?t=42425
This one will be installed on project 663

http://www.syborgtwinturbo.com/albums/Build/2006_10_21_012.jpg

More to come next week.

[black2002ls]

i like that upper grille insert..really helps to clean things up....progress is looking good!

[syborg tt]

i'm looking into having the grille made in fiberglass and having the top completely closed off.

[BLUE'03]

Looking really great.Always look forward to your updates.

[TravisB]

take care of yourself marty........feel free to call if you get bored laying around recovering.....

[syborg tt]

take care of yourself marty........feel free to call if you get bored laying around recovering.....

trust me i plan to be typing away and working on the build book for syborg

[syborg tt]

A couple people have asked what's left before paint at KD Hot Rods. Here is the list that Dave and I are working off of.

To Do Paint & Body
Patch Panel underside of Bed

Billet Bed Shims
Smooth Welds on Inner Fenders of Bed
Smooth Tailgate Handle (Just tacked in)
Adjust Hinges on Tailgate

A-Pillar Body Line

Hood Hinges - Possible Billet
Remove Hood Body Line < (= End Body Line on Front Fender >

Inner Fenders - Smooth
Radiator Cover Shroud

Remote Wiper- Complete

Roll Fender Lips on all Four Corners


Interior
Sheet Metal Dash Conversion (Side Panels)
Mount Gauges

Re-Drill Steering Column

Mount Lokar Hood Release
Mount MSD Coil ( Firewall )
HID Headlight Conversion or H4 Conversion


To Do Engine Bay
Billet Master Cylinders

Mount Over Flow Bottle
Mount Power Steering Tank
Mounting tab on Hogan Intake Valley (FPR)

Turbo Support Bracket

Mount AC/Heat Bulkhead
Mount AC Dryer
A/C Condensor Clearence Grille

Radiator Cap
Install Oil Fill Cap / Spout in Manifold


To do Plumbing
Stainess Brake Lines
Braided Stainless Lines on Trans Cooler.
Braided Stainless Oil Cooler Lines

Y-Block to Engine - back to Fuel Cell

Temp Sender - Radiator (keep one hole open)
Upper Radiator Hose
Lower Radiator Hose

PS Lines
Air Lines (Air Ride)
Shifter Cable
Transmission Dip Stick

Electrical Lines
Starter
Remote Battery
A/C Plumbing


To Do Chassis & Suspension
Misc Underside Welding
Cross Brace
Smooth Welds on the Frame
Tie Rod Sleeve (Talk with Kevin)

Bump Stops on Chassis - Front Suspension
Longer Wheels Studs - Front Spindle's

Drive Shaft

Ground Studs - Firewall, Front Frame, Rear Frame
Ground Studs - Interior firewall, Pump Controller, Radio, Amp, MSD Box

[syborg tt]

Good Mornig All,

I would like to welcome Vintage Air to the sponsor list.
We look forward to working with them on this project.

http://www.syborgtwinturbo.com/albums/Renderings/vintage_air.jpg

We wanted a control unit for the dash that would work with our project.
It's ultra clean and simple looking.

http://www.syborgtwinturbo.com/albums/Build/491200_RUA.jpg

Previously installed in the Vintage Air Heat, Cool, Defrost Gen II Mini

http://www.syborgtwinturbo.com/albums/Build/2006_03_10_030.jpg

More to come next week.
Seems like i just spent a couple hours ordering parts this week.

[syborg tt]

Good Morning All,

Well, this will be the last update for a couple weeks as the big day is Tuesday Morning.

Pictures don't do it Justice. Man are these tires huge!

http://www.syborgtwinturbo.com/albums/Build/2006_11_04_002.jpg

Notice the tire is almost the same height as the body line at ride height.

http://www.syborgtwinturbo.com/albums/Build/2006_11_04_008.jpg

Just like the picture.
PS that is one bad viper hanging in the air. About 300k invested so far.

http://www.syborgtwinturbo.com/albums/Build/2006_11_04_010.jpg

just a quick side shot.

http://www.syborgtwinturbo.com/albums/Build/2006_11_04_011.jpg

okay last one i promise

http://www.syborgtwinturbo.com/albums/Build/2006_11_04_012.jpg

[syborg tt]

Now you can see what the chassis looks like.

http://www.syborgtwinturbo.com/albums/Build/2006_11_04_014.jpg

Here is all of the Air Ride Equipment

http://www.syborgtwinturbo.com/albums/Build/2006_11_04_016.jpg

Dave installed the new Vintage Air Billet Defrost Ducts.

http://www.syborgtwinturbo.com/albums/Build/2006_11_04_018.jpg

Underside view. The ducts are temporally being held in by sheet metal screws.

http://www.syborgtwinturbo.com/albums/Build/2006_11_04_019.jpg

A little more trimming was needed on the dash so it would clear the door panel.
Although we are not using the stock door panels they were used as a guide

http://www.syborgtwinturbo.com/albums/Build/2006_11_04_020.jpg

[syborg tt]

Yep that's a bunch of guy's looking at an upside down bed

http://www.syborgtwinturbo.com/albums/Build/2006_11_04_021.jpg

Yep that's the stink can there Dad.

http://www.syborgtwinturbo.com/albums/Build/2006_11_04_022.jpg

Dave also trimmed out the inner fenders and closed the gap.

http://www.syborgtwinturbo.com/albums/Build/2006_11_04_023.jpg

That's all for this week. I hope to be back online by the weekend.

[black2002ls]

Looking good Marty. That first pic is a little scary. As it looks like there would be some serious rubbing issues with the tank. But the side shots clear it up!! Those things are HUGE. I own a 2003 Dime, and couldn't imagine those things on my truck....on second thought...yeah I could :unibrow:

edit: I also like the way the roll cage ties to the cab very trick!

[syborg tt]

yep they are monsters. I can't wait to see them rolling down the street.

[J2SpeedandCustom]

Good luck and a speedy recovery Marty! We'll all be anixously waiting the next update. :thumbsup:

[Rebird]

Unreal truck!!!! Attention to detail is amazing!!! WOW!!!

[syborg tt]

Feel pretty good.

Was able to talk right after surgery - Very happy

Biopsy of my lymph node came back clear

Still waiting to here back on the thyroid.

But so far so good

just surfing the internet looking at sema pics

[AAW]

Glad you're feeling pretty good now, Marty!
You're still in my thoughts & prayers!
Get well soon.

[kennyd]

glad everything went well .

[syborg tt]

yep feel pretty good - not ready to run any races yet. But at least i'm up and around

[syborg tt]

howdy all

http://www.syborgtwinturbo.com/albums/stjan07/2007_Jan_Sport_Truck_0_r.jpg

http://www.syborgtwinturbo.com/albums/stjan07/2007_Jan_Sport_Truck_00_001.jpg

http://www.syborgtwinturbo.com/albums/stjan07/2007_Jan_Sport_Truck_1_r.jpg

http://www.syborgtwinturbo.com/albums/stjan07/2007_Jan_Sport_Truck_2_r.jpg

http://www.syborgtwinturbo.com/albums/stjan07/2007_Jan_Sport_Truck_3_r.jpg

[race-rodz]

very cool....but why arent the chicks sprawled all over your truck :lol:

[ProTouring442]

Way cool!!! Big time congrats! I'll be happy if I can get some ink once my car is finished, you got ink, and it's not close to being done! :thumbsup:

Shiny Side Up!
Bill
'72 442 "Inamorata"
www.FQuick.com/ProTouring442

[black2002ls]

AWESOME. I'll have to pick up that issue. I've been wanting to start working on my truck. Doing some cosmetic work. but the money just isn't there right now.

[kennyd]

" he is making a appointment with the bodyshop thereafter " wtf ? lol

[syborg tt]

very cool....but why arent the chicks sprawled all over your truck :lol:

yep - now i know what it takes to get on cover. Well in the next issue maybe i'll have to have some 1/2 naked women at the bodyshop.

[syborg tt]

" he is making a appointment with the bodyshop thereafter " wtf ? lol


don't feel bad the engine guy didn't get the credit either

[65 347]

Hi, just started following your build, glad to heard your doing fine and congrates and the magazine spread.

[syborg tt]

Okay i'll post some pics - what the heck

I'm my absence Dave was kind enough to order all of the stainless steel fitting for the brakes.
All $600.00 of them I hope this includes the brake lines.

http://www.syborgtwinturbo.com/albums/Build/2006_11_16_018.jpg

Kevin (who's Kevin) retapped the Masters so we could use these fitting on the them.

http://www.syborgtwinturbo.com/albums/Build/2006_11_16_010.jpg

Once again Kevin put a couple tabs on the frame for the brake line.

http://www.syborgtwinturbo.com/albums/Build/2006_11_16_009.jpg

You can't really see the thru-frame piece but it's really cool.
ps - this is the rear brake line.

http://www.syborgtwinturbo.com/albums/Build/2006_11_16_017.jpg

[syborg tt]

Yep Kevin welded a tab on the Manifold to hold the FPR

http://www.syborgtwinturbo.com/albums/Build/2006_11_16_001.jpg

Pictures not that good but Kevin welded on the Billet Specialties oil bung.

http://www.syborgtwinturbo.com/albums/Build/2006_11_16_003.jpg

One more Bung on the front of the intake Manifold.

http://www.syborgtwinturbo.com/albums/Build/2006_11_16_004.jpg

Kevin Made the lids for the Intake boxes.

http://www.syborgtwinturbo.com/albums/Build/2006_11_16_007.jpg

Okay I think Derrick made the little bracket and Kevin welded it.

[syborg tt]

We just wanted to add something simple to keep the bar from moving up and down.

http://www.syborgtwinturbo.com/albums/Build/2006_11_16_014.jpg

Dave finished the dash sides. It actually looks like a factory dash at first glance.

http://www.syborgtwinturbo.com/albums/Build/2006_11_16_012.jpg

Kevin made the holes adjust able for the remote wiper so we could get the wiper arms perfectly centered.

http://www.syborgtwinturbo.com/albums/Build/2006_11_16_011.jpg

Okay last picture and it's really hard to see what was done.
Dave welded in a piece of tubing to the inner fender to add some strength.

http://www.syborgtwinturbo.com/albums/Build/2006_11_16_019.jpg

I hope everyone had a great Thanks Giving and more pics to come next monday.

[black2002ls]

Looking great Marty. It seems as though every little detail that can possibly be taken care of has. Truely a TOP NOTCH build!!!!

[syborg tt]

okay - quick update

Here is the start of the Billet Hood Hinges.
I want to Thank Paul Kromray for doing the CAD Drawing and Chicago Water Jet for cutting them out for me.

http://www.syborgtwinturbo.com/albums/Build/2006_12_05_001.jpg

We still have to shape the top piece and weld it.

http://www.syborgtwinturbo.com/albums/Build/2006_12_05_002.jpg

[syborg tt]

Here is the new Stereo System that is going in the Truck.
All parts have been donated by Village Auto - Thanks Again Don.

Kenwood DPX501 Head Unit

http://www.syborgtwinturbo.com/albums/Build/2006_12_05_001_DPX501_K_x.jpg

Kenwood KAC-8452 Amp

http://www.syborgtwinturbo.com/albums/Build/2006_12_05_002_kac_8452_x.jpg

Kenwood KFC-P707 6.75" Seperates

http://www.syborgtwinturbo.com/albums/Build/2006_12_05_003_KFC_P707_x.jpg

Kenwood KFC-4675C 4 x 6 Speakers (rear fill)

http://www.syborgtwinturbo.com/albums/Build/2006_12_05_004_kfc_4675c_x.jpg

Kenwood KFC-W2510 10" Subwoofer

http://www.syborgtwinturbo.com/albums/Build/2006_12_05_005_kfc_w2510_x.jpg

That's it for today, I should be going to the shop in the early AM tommorow.
Will have more pics.

[black2002ls]

looking good

[G-Body]

This truck is so well engineered its scary lol :hail:

[syborg tt]

This truck is so well engineered its scary lol :hail:

Thank you - it helps when you apir yourself with some of the best builders out there. I can't wait to finish this project and build the next one.

[Sales@Dutchboys]

Keep up the good work that truck is going to
be a killer ride. When is she going to be on the road?

[syborg tt]

Keep up the good work that truck is going to
be a killer ride. When is she going to be on the road?

Shooting for End of June 07

[syborg tt]

Good Morning All,

Mid Week Update - Will be back at the shop on Saturday to work on the truck again.

This is the complete Intercooler Air Intake & Filter Assembly

http://www.syborgtwinturbo.com/albums/Build/2006_12_06_001.jpg

Side View - Weird looking isn't it.

http://www.syborgtwinturbo.com/albums/Build/2006_12_06_002.jpg

New Ron Davis Radiator.

http://www.syborgtwinturbo.com/albums/Build/2006_12_06_003.jpg

Top Side View

http://www.syborgtwinturbo.com/albums/Build/2006_12_06_007.jpg

Hard to believe put I actually found a Radiator Hose that works.

http://www.syborgtwinturbo.com/albums/Build/2006_12_06_008.jpg

[syborg tt]

Yep it works perfectly

http://www.syborgtwinturbo.com/albums/Build/2006_12_06_009.jpg

Lower Radiator Hose also is off the shelf and it even works perfect.

http://www.syborgtwinturbo.com/albums/Build/2006_12_06_010.jpg

Flex-a-lite Fans Mounted to the Radiator

http://www.syborgtwinturbo.com/albums/Build/2006_12_06_011.jpg

You can see the mounting Tabs that Kevin made for the Fan kit. He still has two more to go.

http://www.syborgtwinturbo.com/albums/Build/2006_12_06_012.jpg

Overflow Tank is mounted

http://www.syborgtwinturbo.com/albums/Build/2006_12_06_013.jpg

[syborg tt]

Front Suspension Stop.

http://www.syborgtwinturbo.com/albums/Build/2006_12_06_015.jpg

We added the 4th bolt on the frame for the Flaming Rivers Steering Box.

http://www.syborgtwinturbo.com/albums/Build/2006_12_06_016.jpg

More to come later this week.

[rocketman]

damn I just noticed this thing has a v-6,that's just sick,is it a stock style v-6 or like one of the old Busch series v-6's

[syborg tt]

damn I just noticed this thing has a v-6,that's just sick,is it a stock style v-6 or like one of the old Busch series v-6's

LOL - yep that dare to be different crowd came over me. Wow was that an expensive choice.

It's actually a Old Bush Series engine except everything is brand new. Yep v6 parts are usally double the cost of v8 parts. My billet crank cost $3000.00 the rods and pistons were just as expensive. Thank God Rockford Racecraft has helped along the way with Sponsorship (cost breaks) on the Parts for the inside of the engine. But I still think i'm near 20 grand for the Long block and intake.

[syborg tt]

okay need some help. Last night I was thinking about the interior. Right now we are focused on the Dash and I am trying to decided if we should paint it or cover it in leather.

Any and all opinions and advice is appreciated.

http://www.syborgtwinturbo.com/albums/Build/2006_11_16_026.jpg

[Sales@Dutchboys]

PLEASE! Paint it! I painted mine And I am sooooo glad I did cover anything on it.

[syborg tt]

PLEASE! Paint it! I painted mine And I am sooooo glad I did cover anything on it.

got pics

[Sales@Dutchboys]

Yea I do do you have a email?

[Sales@Dutchboys]

Ill just link it too you im a PM

[Sales@Dutchboys]

PM sent.

[black2002ls]

I say paint. The only thing I've ever been concerned with on a painted dash is the possibility of a bad glare coming off of the top..

[Sales@Dutchboys]

I would just flat clear it.

[rocketman]

LOL - yep that dare to be different crowd came over me. Wow was that an expensive choice.

It's actually a Old Bush Series engine except everything is brand new. Yep v6 parts are usally double the cost of v8 parts. My billet crank cost $3000.00 the rods and pistons were just as expensive. Thank God Rockford Racecraft has helped along the way with Sponsorship (cost breaks) on the Parts for the inside of the engine. But I still think i'm near 20 grand for the Long block and intake.


That's flat killer.

[syborg tt]

Good Morning All,

Core Support is finally starting to look complete and clean.
Kevin capped the back of the support to give it a finished look.

http://www.syborgtwinturbo.com/albums/Build/2006_12_09_007.jpg

Before - Original Core Support.
Notice the big ugly lip on the core support

http://www.syborgtwinturbo.com/albums/Build/2004_10_04_10.jpg


After.
Now it's nice and smooth

http://www.syborgtwinturbo.com/albums/Build/2006_12_09_008.jpg

Just a quick shoot of the first transition - more to come

http://www.syborgtwinturbo.com/albums/Build/2006_12_09_012.jpg

Kevin is going to make the final shroud over the Radiator.

http://www.syborgtwinturbo.com/albums/Build/2006_12_09_013.jpg

[syborg tt]

Dave removed the inner part of the fender to add clearance.

http://www.syborgtwinturbo.com/albums/Build/2006_12_09_016.jpg

On Saturday we moved up the inner part of the fender to check for clearance.
When the suspension is air out it looks like it's only has to be raised 2".

http://www.syborgtwinturbo.com/albums/Build/2006_12_09_019.jpg

Billet Hinges installed and they look nice. They will still need some finish work.

http://www.syborgtwinturbo.com/albums/Build/2006_12_09_020.jpg

New Tie rod Sleeves - Just trying to clean up the underside a little.

http://www.syborgtwinturbo.com/albums/Build/2006_12_09_023.jpg

That's all for this week.

[kennyd]

i like the coresupport , looks good

[syborg tt]

i like the coresupport , looks good


I am happy you like it since you are going to be the one doing the body work on it.

[syborg tt]

12-14 Update - Radio & Vintage Air Controls

Good Morning All,

The dash is almost complete Dave mounted the Radio & Vintage air controls.

http://www.syborgtwinturbo.com/albums/Build/2006_12_14_001.jpg

Dave needed to do just a little trimming to make it work but it works.

http://www.syborgtwinturbo.com/albums/Build/2006_12_14_009.jpg

Dave also finished the trim piece that goes under the Billet Specialties Steering Column.

http://www.syborgtwinturbo.com/albums/Build/2006_12_14_004.jpg

Once again want to thank Don at Village Auto for taking care of the sound system for me and the guy's at Vintage Air.

[syborg tt]

12-16 Update - Inner Fenders Design

Okay I've been battling this in my mind for weeks if not months.
I wanted something different yet functional and I think we've got it.


This is the basic shape of the inner fender.
We should have plenty of clearance turning the wheel.

http://www.syborgtwinturbo.com/albums/Build/2006_12_16_004.jpg

Here is the Ariel View.
Don't forget there is a 3" Elbow that leads down to the turbo.

http://www.syborgtwinturbo.com/albums/Build/2006_12_16_011.jpg

The look from the core support.
We may need to scallop the inner fender just a little for the turbo.
It's hard to tell in the picture but the Turbo is 1.5" from the inner fender.

http://www.syborgtwinturbo.com/albums/Build/2006_12_16_013.jpg

View from the Drivers Side
The transition will be a little softer, it's really hard to make chipboard bend.

http://www.syborgtwinturbo.com/albums/Build/2006_12_16_014.jpg

Okay last view.

http://www.syborgtwinturbo.com/albums/Build/2006_12_16_015.jpg

More to come later in the week.

[syborg tt]

12-18 Update - P-Side Inner Fender Update

Dave was kind enough send me pictures of the Drivers Side Inner Fender

Remember this is still a work in progress -- plenty more details to add.

http://www.syborgtwinturbo.com/albums/Build/2006_12_18_0.jpg

Side View

http://www.syborgtwinturbo.com/albums/Build/2006_12_18_2.jpg

Turbo's Mounted

http://www.syborgtwinturbo.com/albums/Build/2006_12_18_3.jpg

Dave is going to clearance them just a little around the Turbo.

http://www.syborgtwinturbo.com/albums/Build/2006_12_18_4.jpg

And did I mention they are all steel baby.

[black2002ls]

looking good marty

[71Nova]

That looks great Marty. Your truck is really coming along!!

[XcYZ]

Cool, keep it up Marty. Love the updates. :thumbsup:

[syborg tt]

Good Morning All,

I would like to welcome a new Sponsor.

George Blake of Prime Gears.

http://www.syborgtwinturbo.com/albums/Renderings/prime_gears.gif

New Shifter Cable and 4l80e Bracket.

http://www.syborgtwinturbo.com/albums/Build/2006_12_22_008.jpg

Quick look at all the new Parts

Headlights, Shifter Cable, Fuel Block Off Plate, Injectors & Hood Lifts.

http://www.syborgtwinturbo.com/albums/Build/2006_12_22_002.jpg

Fuel Block Off plate Compliments of John Gerber - Thanks John.

http://www.syborgtwinturbo.com/albums/Build/2006_12_22_004.jpg

Headlights - Thanks James

http://www.syborgtwinturbo.com/albums/Build/2006_12_22_006.jpg

I also want to Thank Jon at Bully Racing for hooking me up with the injectors.
Jons and awesome guy.

[syborg tt]

Merry Christmas to all,

It's been a long time coming and they are finally complete.

It's hard to believe that after making at least 15 different chipboard versions
we finally have Inner Fenders.

This gives you an idea how much of the Fenders structure needed to be removed to make room
for the tire when the truck is lowered.

http://www.syborgtwinturbo.com/albums/Build/2006_12_21_001.jpg

You can see how the inner fender is mounted to the firewall.
Mounting from the underside hides all the hardware in the engine bay.

http://www.syborgtwinturbo.com/albums/Build/2006_12_23_009.jpg

Dave beed rolled the Inner Fender to add strength.

http://www.syborgtwinturbo.com/albums/Build/2006_12_23_019.jpg

Close up view of the front of the inner fender.
We still have to drill 2 access holes in the front of the fender to remove the air boxes.

http://www.syborgtwinturbo.com/albums/Build/2006_12_23_016.jpg

Quick Picture with the Turbo and Downpipe installed.

http://www.syborgtwinturbo.com/albums/Build/2006_12_23_015.jpg

[syborg tt]

The engine bay with both inner fenders. I am very happy with the Final product.
You can tell there custom but yet they look stock and maintain the original goal of the truck to make it appear as a factory prototype.

http://www.syborgtwinturbo.com/albums/Build/2006_12_23_004.jpg

Air Inlet from the Intercooler has plenty of clearance.

http://www.syborgtwinturbo.com/albums/Build/2006_12_23_023.jpg

Air box installed.

http://www.syborgtwinturbo.com/albums/Build/2006_12_23_025.jpg

Thanks again for watching the build of my truck this last year.
It has been a blast to build and I can't wait to see it finally get painted.
This next year promises to be very exciting.

[Sales@Dutchboys]

Looks great! Thanks for the pics.

[black2002ls]

Lookin' good Marty, :thumbsup: .

[syborg tt]

Some say better late then never.

I have a bunch of updates to do so i will post them individually

Dave had to reroute one of the air intake tubes to get around the new inner fender.

http://www.syborgtwinturbo.com/albums/Build/2006_12_26_006.jpg

http://www.syborgtwinturbo.com/albums/Build/2006_12_26_008.jpg

We finally made the new lower column mount.

http://www.syborgtwinturbo.com/albums/Build/2006_12_27_041.jpg

Kevin mounted the Power Steering Tank from Billet Specialties

http://www.syborgtwinturbo.com/albums/Build/2006_12_27_042.jpg

It was hard but we finally found a location for the a/c drier.
See if you can guess where it's mounted.

http://www.syborgtwinturbo.com/albums/Build/2006_12_27_043.jpg

[syborg tt]

Dave also mounted the hood pin in the core support.
Ron & I are working on the Skuff plate for the hood.
Pics very soon I promise.

http://www.syborgtwinturbo.com/albums/Build/2006_12_27_044.jpg

Normally I would say something like more to come next week.
But since I am already 2 weeks behind.

Well someone took the body off my truck.

No actually Dave & Kevin removed it so they could plumb the brake lines.

http://www.syborgtwinturbo.com/albums/Build/2006_12_29_017.jpg

http://www.syborgtwinturbo.com/albums/Build/2006_12_29_018.jpg

http://www.syborgtwinturbo.com/albums/Build/2006_12_29_019.jpg

http://www.syborgtwinturbo.com/albums/Build/2006_12_29_020.jpg

That's it just thought i would post some pics

[syborg tt]

Just some quick pictures I thought were cool.

http://www.syborgtwinturbo.com/albums/Build/2006_12_29_022.jpg

Close up of the hood pin

http://www.syborgtwinturbo.com/albums/Build/2006_12_29_024.jpg

Added a second battery just in case.

http://www.syborgtwinturbo.com/albums/Build/2006_12_29_025.jpg

still plenty more post to follow

[syborg tt]

Dave ran all the brake lines while the body was off.

This way they could keep everything tight to the frame.

http://www.syborgtwinturbo.com/albums/Build/2006_12_29_026.jpg

Man I can't wait till the frame is painted.

http://www.syborgtwinturbo.com/albums/Build/2006_12_29_027.jpg

Brake line running over the rear hoop.

http://www.syborgtwinturbo.com/albums/Build/2006_12_29_028.jpg

T-Fitting to get the Drivers Side rear Brake.

http://www.syborgtwinturbo.com/albums/Build/2006_12_29_029.jpg

Quick Shot of the brake line following the frame.

http://www.syborgtwinturbo.com/albums/Build/2006_12_29_030.jpg

[syborg tt]

This is where the brake line terminates on the frame.

http://www.syborgtwinturbo.com/albums/Build/2006_12_29_031.jpg

yep there will be more posts

[syborg tt]

While I was in Florida.
I stopped by www.Docskustom.com to have him work on the final dash bezel.
All I can say is what a great guy.

http://www.syborgtwinturbo.com/albums/Build/2006_12_31_004.jpg

http://www.syborgtwinturbo.com/albums/Build/2006_12_31_005.jpg

http://www.syborgtwinturbo.com/albums/Build/2006_12_31_010.jpg

http://www.syborgtwinturbo.com/albums/Build/2006_12_31_012.jpg

http://www.syborgtwinturbo.com/albums/Build/2006_12_31_013.jpg

yep still more.

[syborg tt]

Really, I had to take picture of the motor while it was out of the truck.

Dave and I worked on a design for the Turbo Support Brackets.
It will follow the same theme as the Billet Specialties Brackets

http://www.syborgtwinturbo.com/albums/Build/2007_01_04_006.jpg

Kevin Boxed in the motor mounts.
Yes, there is a drain hole in the back just in case they get wet.

http://www.syborgtwinturbo.com/albums/Build/2007_01_04_008.jpg

Dave also finished the brake lines in the front.

http://www.syborgtwinturbo.com/albums/Build/2007_01_04_009.jpg

Side shot.

http://www.syborgtwinturbo.com/albums/Build/2007_01_04_010.jpg

Harness Bar is welded.
Looks like it's getting really close to coming home to my shop.

http://www.syborgtwinturbo.com/albums/Build/2007_01_04_011.jpg

[syborg tt]

What more brake line pics.

http://www.syborgtwinturbo.com/albums/Build/2007_01_04_013.jpg

Just another one of those really expensive t-fittings.

http://www.syborgtwinturbo.com/albums/Build/2007_01_04_014.jpg

Radiator cover.
Trying to stick with the keep it simple theme.

http://www.syborgtwinturbo.com/albums/Build/2007_01_04_035.jpg

Your not going to believe it one more post.

[syborg tt]

Well, It's hard to believe.

I dropped the truck off at Comp Fab in March of 2005 and it's finally coming home.

This will be the last pictures of the truck at Dave's for some time.

http://www.syborgtwinturbo.com/albums/Build/2007_01_07_002.jpg

on the ground

http://www.syborgtwinturbo.com/albums/Build/2007_01_07_004.jpg

Outside on the trailer - getting ready to go home.

http://www.syborgtwinturbo.com/albums/Build/2007_01_07_006.jpg

http://www.syborgtwinturbo.com/albums/Build/2007_01_07_007.jpg

At home in my shop.

http://www.syborgtwinturbo.com/albums/Build/2007_01_07_008.jpg

Okay now I can say plenty more to come soon.

[Leadfoot1]

Hey Marty,

How about we change the title of the post.....2 years later its not a "new" project and not a new member anymore!!! ;)

Every time i see this i think someone is goint to do something like you.


Looks awesome!:thumbsup:

Keep us posted.

Lead

[syborg tt]

How about we change the title of the post.....2 years later its not a "new" project and not a new member anymore!!! ;)



Scott,

Maybe Lead has a good idea :yes: :willy:

[black2002ls]

Sweet Euphoria! Great update, things are really looking good. Oh and a guess on where you mounted the AC Drier. It appears to be behind the intercooler mounted to the core support

[907rs]

Scott,

Maybe Lead has a good idea :yes: :willy:

You're hooked up, Marty.

[Alex396ss]

Lookin´good!

:thumbsup: :thumbsup: :thumbsup:

Alex

[Leadfoot1]

You're hooked up, Marty.

Guy's!

I was only kidding!!! But hey, its cool.

:D

Lead.

(happy it was taken the way i intended it to be :cheers: )

[syborg tt]

You're hooked up, Marty.


Now that is awesome - I love it.

[71Nova]

Its really coming together! It is amazing how long this project is taking to complete even though you are extremely active on it. Can't be to much longer.

[GHOSTDANCER]

Keep on Truckin:thumbsup:

[syborg tt]

Its really coming together! It is amazing how long this project is taking to complete even though you are extremely active on it. Can't be to much longer.

i wish that was the case. If you saw the list you would be shocked at how much is left to do. I am hoping to have it complete by the Power Tour but i am not sure i can do it.

[TEDDYS CAMARO]

YOU CAN DO IT!!!!:willy:

[syborg tt]

YOU CAN DO IT!!!!:willy:

Teddy you crack me up - I just wish i was as far a long as your bad ars ride.

[71Nova]

i wish that was the case. If you saw the list you would be shocked at how much is left to do. I am hoping to have it complete by the Power Tour but i am not sure i can do it.

Who cares if it is done by this power tour. You are taking your time and doing every little detail perfectly. I dont see power tours ending any time soon. When it is done, you can take it on power tour and know that everything is perfect and not rushed. I always wanted to build aV6 4.3 twin turbo for a corvair. I love that you are using this engine. Everything on your truck is custom formed so it takes time. When you are done you will most likely have the best and funnest S-10 the world has ever seen.

[syborg tt]

ya know i couldn't agree with you more.

I slightly burned out working to much and i am trying to finish my garage so i can have heat in my garage. Who would of thought framing in an attic for parts and insulating would cost 1,000 in materials alone.



Who cares if it is done by this power tour. You are taking your time and doing every little detail perfectly. I dont see power tours ending any time soon. When it is done, you can take it on power tour and know that everything is perfect and not rushed. I always wanted to build aV6 4.3 twin turbo for a corvair. I love that you are using this engine. Everything on your truck is custom formed so it takes time. When you are done you will most likely have the best and funnest S-10 the world has ever seen.

[65 347]

Marty, nice to see the truck at home, give me a call I'd love to give you a hand, plus it would give me a excuse to return your tool.

[syborg tt]

Marty, nice to see the truck at home, give me a call I'd love to give you a hand, plus it would give me a excuse to return your tool.

pm me your number left it at work.

Still trying to finish the garage before i strip the truck down.

[syborg tt]

Happy Wednesday,

Okay I wanted to send this out yesterday but I just plumb ran out of time.

Carter Hickman is the man.
He did an incredible job on the 3-D rendering of my truck.

It has the actual wheels, Brakes, exhaust cut out & bed cover.

http://www.syborgtwinturbo.com/albums/Renderings/syborgTT_Final640.jpg


If your looking for idea's as to what you ride may look like.
Send him a e-mail. ( [email protected] )

If you want to see some of the other renderings he did you can view them here.
http://www.syborgtwinturbo.com/gallery/chd

Carter has got to be one of the best vendors I have every worked with.
End of Story!!!

[TEDDYS CAMARO]

Very nice. Looks great. I hope we meet at the power tour. If not, we got plenty of time. It's all about having fun.

[syborg tt]

Good Morning All,

Okay I haven't had time to work on the truck the last two weeks.
Seems working on the Garage has taken precedence. It's very hard to be in the garage when it's 20 degrees.

I needed to build an attic so I could have a place to put the parts once I disassembled the truck.
So plans are to build an attic over the front half of my garage.

http://www.syborgtwinturbo.com/albums/Build/2007_01_02_001.jpg

Sixteen twenty foot 2 x 8's, ten sheets of 1/2" plywood & twenty-one eight foot 2 x 6's later we have an attic.
Next time I plan to get some friends to help. Those 20 foot 2 x 8's are brutal to lift by your self.

http://www.syborgtwinturbo.com/albums/Build/2007_01_11_001.jpg

Eight more Ten foot 2 x 6's for the vaulted ceiling (need the height for the lift).
Did I mention I hate ladders let alone working at 12 feet in the air?

http://www.syborgtwinturbo.com/albums/Build/2007_01_11_003.jpg

Now it's time for the itchy stuff.

http://www.syborgtwinturbo.com/albums/Build/2007_01_13_001.jpg

Okay the back half of the garage is Insulated.
Now I need to put up a temporary wall and insulate the new attic floor.
I almost forgot -- I really need to clean up this mess.

http://www.syborgtwinturbo.com/albums/Build/2007_01_14_005.jpg