Looking for header builder in Nor Cal area anyone?

[Solid LT1]

Anyone have experience with a good shop to build a set of LS3 swap headers? I have motor/trans mocked up in the car and want a nice set of stainless Tri-y headers built. I can haul car to location. Need someone who knows how to build merge type collectors....thanks for your feedback.

[ironworks]

Anyone have experience with a good shop to build a set of LS3 swap headers? I have motor/trans mocked up in the car and want a nice set of stainless Tri-y headers built. I can haul car to location. Need someone who knows how to build merge type collectors....thanks for your feedback.

We do it all the time, but might be a little far away. Just be prepared that kinda work is very time consuming. Be sure no one make what you need first. You will be money ahead.

[Damn True]

Sanderson?

[NOPANTS68]

I had a guy named Boyd Ferry build me some stepped headers for my FFCobra. nicest set I've ever seen. He is next door to Sanderson headers in South SF about two doors down from Brizio. It's been years, but I'm sure Sanderson has his digits.

[garickman]

For more than 30 years the only thing this guy has done in life is build headers.

http://perfweldheaders.com/index.html

[Vince@Meanstreets]

Anyone have experience with a good shop to build a set of LS3 swap headers? I have motor/trans mocked up in the car and want a nice set of stainless Tri-y headers built. I can haul car to location. Need someone who knows how to build merge type collectors....thanks for your feedback.

Peter Weber is a master fabricator. We have used him before and he doesn't disappoint. He's near you to boot.

http://www.yelp.com/biz/pete-weber-performance-products-newark?nb=1

[Solid LT1]

For more than 30 years the only thing this guy has done in life is build headers.

http://perfweldheaders.com/index.html

Thanks that may be the guy my buddy Bob Wirth told me about, since he is too busy with an Australian Pro Stock engine program right now.

[408sbfmustang]

http://www.lemonsheaders.com/contact.htm
http://www.sandersonheaders.com

[Ricochet]

If you decide to go down south to Ironworks I can attest their work is phenomenal! They did my entire system. If not there is a guy east of Sacramento in Loomis called BigHead Motorsports. Alex Guiterez. He does awesome work and great to deal with as well.

Check out this thread for some of his work.
http://www.lateral-g.net/forums/showthread.php4?t=40441

FB page
https://www.facebook.com/pages/Big-Head-Motorsports/309703072375898

[ironworks]

If you decide to go down south to Ironworks I can attest their work is phenomenal! They did my entire system. If not there is a guy east of Sacramento in Loomis called BigHead Motorsports. Alex Guiterez. He does awesome work and great to deal with as well.

Check out this thread for some of his work.
http://www.lateral-g.net/forums/showthread.php4?t=40441

FB page
https://www.facebook.com/pages/Big-Head-Motorsports/309703072375898

I forgot about Alex, he does good work also up in your area.

[EBMC]

Were less than an hour away


A set we did for the shop race car...
http://i864.photobucket.com/albums/ab208/2468ebmc/race%20car/6858847071_a142e7f800_b_zpsdaaf6716.jpg (http://s864.photobucket.com/user/2468ebmc/media/race%20car/6858847071_a142e7f800_b_zpsdaaf6716.jpg.html)

[NOPANTS68]

Yeah big head is off the hook. I forgot about him as well.

[JB64CHEVELLE]

Also try Mike Bola at Enterprise motorsports in Newark. He does very nice work but he is always swamped with work so it's hard to get in.

[Wissing72]

Look at Ultimate Headers also. I have them for my car. Very nice pieces.
http://ultimateheaders.com/

[garickman]

Were less than an hour away

I forgot about Steve, the guys at EBMC real bad asses and not to far from you. I can tell you it would be well worth your trip to check out what they have going on in the shop.