ProCharged 406 for sale

[camcojb]

This one is from the blue Camaro on my website. It made 691 rwhp on pump gas. He's decided he wants an aluminum 540 so this engine is being sold complete. Good running engine with no issues.

http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=8051409661

Jody

[fletcherscustoms]

Very interested! What would it take to get everything to make turn key?? allteh belts, hoses, brackets, etc?

[rocketrod]

How streetable is this motor with a "partial block fill"? Any overheating issues? Also does the motor have an aftermarket block?

[camcojb]

Very interested! What would it take to get everything to make turn key?? allteh belts, hoses, brackets, etc?

All the blower specific stuff is there. The stock radiator and heater hoses work. A normal front mount alternator works fine.

Jody

[camcojb]

How streetable is this motor with a "partial block fill"? Any overheating issues? Also does the motor have an aftermarket block?

It is a factory 400 2 bolt block. The partial fill is something I've done on all three of these I've had. None had cooling issues. Almost required with the GM block and high hp.

This one never went over 180 degrees. I remember being stuck for a train on a 100+ degree day and we let it idle for the full 15 minutes it took for the super-slow moving train. It would hit 180 degrees, the computer turned the Mark VIII fan on and it would cool back to 170 degrees where the computer shut the fan off. This happened a few times, slowly building back up in temp while the fan was off. As soon as the fan started it didn't gain a single degree of temp, just headed back down.

Jody

[MaxHarvard]

Damn that sure is purdy!! Wish i could make it mine :(

[Yenko boy]

Camcojb you have a pm.

[Fluid Power]

Jody,

Can you run the front runner system with this setup?

Darren

[camcojb]

Jody,

Can you run the front runner system with this setup?

Darren

Not without a lot of work if at all. The blower has specific spacing and pulleys to work with their mount, all of which will be in the way of a front runner. Now if a guy wanted to fab up his own custom blower mount to put it in line with the front runner stuff then it's probably possible.

Jody

[Fluid Power]

I should have edited my post, After thinking about how it would work, I should have known! Thanks for the reply.

Darren

[rocketrod]

Did anyone else who was bidding on this motor get a Second Chance offer from an eBay scammer, email address [email protected]? Well I did! He's wants to OFFER me the motor for $1300 less than my max bid and almost $2,000 less than the highest bid. I sent him a reply and told him I will take it! :thumbsup: I'll keep you posted with any replies I get....this could be interesting. I also called Jody already to let him know.

[camcojb]

Did anyone else who was bidding on this motor get a Second Chance offer from an eBay scammer, email address [email protected]? Well I did! He's wants to OFFER me the motor for $1300 less than my max bid and almost $2,000 less than the highest bid. I sent him a reply and told him I will take it! :thumbsup: I'll keep you posted with any replies I get....this could be interesting. I also called Jody already to let him know.

Buy it! Thanks for the call. Think I'll send an e-mail to the other bidders just in case.

Jody

[rocketrod]

Buy it! Thanks for the call. Think I'll send an e-mail to the other bidders just in case.

Jody
I'm all over it!!!!! I just sent the scammer a reply letting him know I'll take it! Be interesting to what his reply is.

[XcYZ]

Cool, keep us posted, I want to see how this plays out.

[rocketrod]

Well I got a reply from the scammer and I am looking for input. I started a new thread. Just click the link below and give more your ideas. :yes:

http://www.lateral-g.net/forums/showthread.php4?p=42404#post42404