Project "Evade"

[68/Camaro]

Well its finally coming together Project "Evade" thank God for Tom Argue @ HydroIllusions! here is Project “Evade” LS2 Build specs
LS-2
Bore and stroke: 4.00 x 3.62 in.
Displacement: 364 cu. in. (5.967 liters)
Compression: 10.9:1
Induction System: Sequential fuel injection
Gross Horsepower (SAE net) 400 @ 6000 rpm
Gross Torque (SAE net) 400 lb.-ft. @ 4400 rpm
Block All-new 319-T5 Aluminum

Livernois Heads:
Stage 2 CNC Ported Stage 2 GM LS-Series Cylinder Heads
New GM 243 casting
5 axis CNC machined
220cc Intake Runner
Intake Flow Rate 305 CFM
Exhaust Flow Rate 235 CFM
2.000 intake valves / 1.550 exhaust valves
GM valve seals and locks
Livernois dual coil valve springs good to ~ .690 lift
Livernois titanium retainers.--Jessel 1.7 Rollor rockers

Livernois Motorsports LS-Series Stage 2 Camshaft
Intake Duration 232 @ .050
Exhaust Duration 232 @ .050
Intake Lift .595”
Exhaust Lift .595
LSA 114

Fast 92mm Intake ,Fast 92mm T.B. ,Fast Fuel Rails, 42lb Fuel Injectors, Katech Valve Covers
AutoKraft Oil Pan & Engine Mounts, Synister Billet LS Series Serpentine Belt Systems
SpearTech Custom Wiring Harness

Suspension/Chassis:
Front Sub Frame
Speed Tech Performance • NEW Design hi clearance upper and lower control arms with Moog TM Problem Solver ball joints, QA1 single adjustable coil over shocks, QA1 coil springs, Billet aluminum upper coil over mounts, Unisteer complete rack kit.Adjustable trans cross member will fit to a T56, 1.25"solid sway bar (only works with HiClearance control arm package) ,Adjustable motor Mounts, Brakes Front: Wilwood Disc Red 4 piston calipers Dynalite 12.19" Disc

Rear Suspension Chris Alston's Chassisworks Camaro g-Bar Suspension
With Pivot Ball Lower Link adjustable length link,
Low-friction, pivot ball mechanisms.,G-Bar Sliding-Link Adjustable Anti-Roll Bar,VariShock Single adjustable coil-Oversm,Wilwood Disc Red 4 piston calipers Dynalite 12.19" Disc

Keisler Engineering Inc. TKO-600 5 speed Lakewood SFI Steel Bellhousing for Chevrolet LS, Hydraulic Clutch Actuator Kit

Rear End: Strange Engineering
S60, S/T Series 35-spline axles, 1/2” studs, Trac-Lok Posi unit, 3.73 gears
Brakes Rear: Wilwood Disc Red 4 piston calipers Dynalite 12.19" Disc

Here is the Project before tear down
http://i700.photobucket.com/albums/ww1/wpano/September-2008/68camaro1.jpg

Out with the Old small block and front subframe
http://i700.photobucket.com/albums/ww1/wpano/September-2008/68camaro19.jpg

Mocking up the New Speedtech Subframe and LS-2 Motor
http://i700.photobucket.com/albums/ww1/wpano/September-2008/68camaro23.jpg

Speedtech Subframe and LS-2 Motor with Keisler Transmission
http://i700.photobucket.com/albums/ww1/wpano/August-2008%20Speedtech-Keisler/Picture074.jpg

[Aschle]

Very nice !! Looking forward to updates...

Jason

[tones2SS]

Yeah, looks like a fun project.
Keep us posted.:thumbsup:

[awr68]

Coming along nicely! Keep us updated!! :thumbsup:

[68/Camaro]

Here are some Better updated Pics
http://i700.photobucket.com/albums/ww1/wpano/December%2026%20Evade/LS-2-Motor.jpg
http://i700.photobucket.com/albums/ww1/wpano/December%2026%20Evade/LS-2-Motor-4.jpg
http://i700.photobucket.com/albums/ww1/wpano/December%2026%20Evade/LS-2-Motor-3.jpg
http://i700.photobucket.com/albums/ww1/wpano/December%2026%20Evade/LS-2-Motor-5.jpg
http://i700.photobucket.com/albums/ww1/wpano/December%2026%20Evade/Picture003.jpg

[tones2SS]

I'm very interested on your opinions on your Speed-tech sub frame after the car is assembled. I really want to go with DSE, but it may be too much money.
Again, nice build!!:thumbsup:

[tumper93]

I'm very very interested in a set of wheels like that!!:unibrow:

[syborg tt]

I've heard so much about it from Tom and It's good to see pics of the car.

Looks really nice - Looking forward to more updates.

[68/Camaro]

Here are Current updated picts of the Undercarriage
http://i700.photobucket.com/albums/ww1/wpano/December%2031%20Undercarriage/Picture001.jpg
Undercarriage Tunnel
http://i700.photobucket.com/albums/ww1/wpano/December%2031%20Undercarriage/Picture002.jpg
Rear Undercarriage with Chris Alston's New G-Bar
http://i700.photobucket.com/albums/ww1/wpano/December%2031%20Undercarriage/Picture005-1.jpg
http://i700.photobucket.com/albums/ww1/wpano/December%2031%20Undercarriage/Picture003.jpg
http://i700.photobucket.com/albums/ww1/wpano/December%2031%20Undercarriage/Picture004-1.jpg

[thedude327]

Great looking project. That finish on the underbody looks fantastic !! What did you use on it?

Paul

[68/Camaro]

Great looking project. That finish on the underbody looks fantastic !! What did you use on it?

Paul

U-Pol Raptor Liner!

[GHOSTDANCER]

Very clean, looks good :thumbsup: :cheers:

[68/Camaro]

Here are a few updates Tom Installed the Strange-60 rear end and Chris Alston's Chassisworks Camaro g-Bar Suspension upgraded the Lower bars to the "Pivot Ball Lower Link" and added Sliding-Link 5/8”-diameter Adjustable Anti-Roll sway bar.
Installed Ricks Tank and ran the fuel rail see pics Also We are test fitting the "Stainless Works" 3' Exhaust !:razz:
http://i700.photobucket.com/albums/ww1/wpano/January%209%202009/Picture009.jpg


http://i700.photobucket.com/albums/ww1/wpano/January%209%202009/Picture008-1.jpg



http://i700.photobucket.com/albums/ww1/wpano/January%209%202009/Picture013.jpg




Also Tom Finished the Katech Valve Covers to match Intake
http://i700.photobucket.com/albums/ww1/wpano/January%209%202009/Picture024.jpg


http://i700.photobucket.com/albums/ww1/wpano/January%209%202009/Picture025.jpg

[68/Camaro]

http://i700.photobucket.com/albums/ww1/wpano/January%209%202009/Picture013.jpg

Stainless steel Fuel Rail
http://i700.photobucket.com/albums/ww1/wpano/January%209%202009/Picture015.jpg


http://i700.photobucket.com/albums/ww1/wpano/January%209%202009/Picture021.jpg

[tones2SS]

That car is looking awesome!!!
Keep us updated. I agree with the undercarriage, in that it looks GREAT!!:thumbsup:

[Hemi Nova]

Nice ride!
I don't stop and see Tom for a couple months and this is what he does. I guess i better stop by and take a look.

[68/Camaro]

Test fitting Carbon Fiber Hood & Valence from Anvilauto thanks to matt!
http://i700.photobucket.com/albums/ww1/wpano/January%2013%202009/Picture011.jpg

http://i700.photobucket.com/albums/ww1/wpano/January%2013%202009/Picture005.jpg


http://i700.photobucket.com/albums/ww1/wpano/January%2013%202009/Picture007-1.jpg

http://i700.photobucket.com/albums/ww1/wpano/January%2013%202009/Picture012.jpg

http://i700.photobucket.com/albums/ww1/wpano/January%2013%202009/Picture013-1.jpg

[syborg tt]

the car looks great - it's fun working with such a great guy as Tom.

ps - thanks for the sneak peak of the other 68

[tony byram]

Great looking car! Im wondering though, that Camaro on the lift in the background, what type of wheels are those? Like to see a better shot of them, if you can get one. :thumbsup:

[syborg tt]

Great looking car! Im wondering though, that Camaro on the lift in the background, what type of wheels are those? Like to see a better shot of them, if you can get one. :thumbsup:


Those wheels are from Ryan at DPE Engineering. His stuff is over the top !!!!

http://dpengineering.cc/

[email protected]

they even have a myspace page ( really i need to get up with the times )

http://www.myspace.com/dpewheels

[syclonetommy]

the car looks great - it's fun working with such a great guy as Tom.

ps - thanks for the sneak peak of the other 68

That pic is just for you, Thought you would like it.

More sneak peaks to come??????


Thanks Bro,

Tom

[syclonetommy]

Nice ride!
I don't stop and see Tom for a couple months and this is what he does. I guess i better stop by and take a look.


Doors aways open?

it's been more than a couple of mouths?
Stop by a see the new little one.


Tom

[Vegas69]

Looking killer!!

[68/Camaro]

the car looks great - it's fun working with such a great guy as Tom.

ps - thanks for the sneak peak of the other 68

I Agree! Tom is Awesome! Excellent to work with!:thumbsup:

[Hemi Nova]

Doors aways open?

it's been more than a couple of mouths?
Stop by a see the new little one.


Tom

I know!
I'll see if i have some extra time Saturday.
Project looks good as always.

[68/Camaro]

Here is the Front Carbon Fiber Spoiler from Brian @ Screamin' Performace

http://i700.photobucket.com/albums/ww1/wpano/IMG_3764.jpg

Also Received on Friday Prodigy Customs Cool Package LSX radiators Thanks Frank!
http://i700.photobucket.com/albums/ww1/wpano/67-69camaroLS1FS.jpg

[68/Camaro]

Test fitting Hinges and Trunk
http://i700.photobucket.com/albums/ww1/wpano/January%2019%202009/Picture013.jpg

Anvilauto CF Deck lid
http://i700.photobucket.com/albums/ww1/wpano/January%2019%202009/Picture004-1.jpg

[bigtyme1]

Love the hinges. How hard were they to put on and did it change the hieght of the deck lid?

[Blake Foster]

Bill honestly................ car is wicked!
thanks for choosing us to help be a part of it

[68/Camaro]

Bill honestly................ car is wicked!
thanks for choosing us to help be a part of it

Blake,
I cant thank you enough for your support you guys are Great to deal with! Awesome service!:thumbsup:

[68/Camaro]

Here are some current updated pics on Evade Front clip on and fitting adjustments How about that CF Hood From Matt @ Anvilauto

http://i700.photobucket.com/albums/ww1/wpano/Febuary-12-13-2009/Picture051.jpg

http://i700.photobucket.com/albums/ww1/wpano/Febuary-12-13-2009/Picture050.jpg

http://i700.photobucket.com/albums/ww1/wpano/Febuary-12-13-2009/Picture045.jpg

http://i700.photobucket.com/albums/ww1/wpano/Febuary-12-13-2009/Picture064.jpg

[68/Camaro]

A Sneak peek of Engine Compartment

http://i700.photobucket.com/albums/ww1/wpano/Febuary-12-13-2009/Picture028.jpg

http://i700.photobucket.com/albums/ww1/wpano/Febuary-12-13-2009/Picture032.jpg

[68/Camaro]

Peek at the rear with Chris Alston's G-Bar and Ricks Tank

http://i700.photobucket.com/albums/ww1/wpano/Febuary-12-13-2009/Picture069.jpg

http://i700.photobucket.com/albums/ww1/wpano/Febuary-12-13-2009/Picture070.jpg

[syborg tt]

wow looks like some quality work going on there.

[68/Camaro]

wow looks like some quality work going on there.

yes! Tom is doing a Great Job!!

[tones2SS]

yes! Tom is doing a Great Job!!

I agree. Car is looking awesome.
Keep us posted please.:thumbsup:

[waynieZ]

Everything looks awesome very nice work. Sweet setup.

[68/Camaro]

Well we just finished installing the (Flush Mount Glass System) by Classic Auto Glass Innovations! Thanks to Robert (Iamtheonlyreal1) on Pro-Touring.com able to get a set of Flush Mount Glass to us! http://classicautoglassinnovations.com/index.html
Guys this glass system is Excellent the pictures don’t do it justice in person it’s beautiful! If you’re looking to install yourself please I suggest contacting your local Auto Glass Company like I did it, and One phone call to Robert made it easier to install, Frank from C Thru Glass our local Glass installer stated it is an excellent product for updating the fist gen Camaro’s it took about 3 hrs from start to finish.
Take a look!
http://i700.photobucket.com/albums/ww1/wpano/Flush%20Mount%20Glass-02-2009/Picture010.jpg
http://i700.photobucket.com/albums/ww1/wpano/Flush%20Mount%20Glass-02-2009/Picture008.jpg
http://i700.photobucket.com/albums/ww1/wpano/Flush%20Mount%20Glass-02-2009/Picture042.jpg

[68/Camaro]

Inside Rear Glass
http://i700.photobucket.com/albums/ww1/wpano/Flush%20Mount%20Glass-02-2009/InsideRearGlass.jpg
http://i700.photobucket.com/albums/ww1/wpano/Flush%20Mount%20Glass-02-2009/InsideRearGlass-2.jpg

Front Windshield
http://i700.photobucket.com/albums/ww1/wpano/Flush%20Mount%20Glass-02-2009/Picture015.jpg
http://i700.photobucket.com/albums/ww1/wpano/Flush%20Mount%20Glass-02-2009/Picture018.jpg

Will Post more Pictures when Completed

[WSSix]

looking very good. The engine looks great

[tones2SS]

Car looks awesome.
Some great work going on there. I LOVE those FESLER trunk hinges!:thumbsup:

[AALynch]

Will you see any benefits out of the window setup, other than for looks? It seems like it would reduce windshield noise quite a bit?

Thanks,
-Adam

[68/Camaro]

Pics on Garagescen
http://garagescene.net/gallery2/v/Builders/TA+Design/68+Camaro+TAD+Evade/

[68/Camaro]

Ok Here is the Package tray and rear seat area
Covererd with sound deadening

http://i700.photobucket.com/albums/ww1/wpano/Febuary-25-2009/IMG_0998.jpg

http://i700.photobucket.com/albums/ww1/wpano/Febuary-25-2009/IMG_1000-11.jpg

[68/Camaro]

Special thanks to Zak Kingsland @ Boze Alloy's for getting me the rear wheels in (Pro-Touring Mesh) 19 X 10

http://i700.photobucket.com/albums/ww1/wpano/March-27-2009/Boze-RearWheel.jpg
http://i700.photobucket.com/albums/ww1/wpano/March-27-2009/Boze-RearWheel-1.jpg

Also Tom is finishing up the wiring harness on the engine special thanks to John @ Speartech! **please note orange tape not incuded LOL

http://i700.photobucket.com/albums/ww1/wpano/March-27-2009/Ls-Engine-2.jpg
http://i700.photobucket.com/albums/ww1/wpano/March-27-2009/Ls-Engine-3.jpg
http://i700.photobucket.com/albums/ww1/wpano/March-27-2009/Ls-Engine.jpg

[68/Camaro]

We Mounted the Front and Rear tires today
Rear 19 X 10 with 5.5 Backspacing and the 275/35ZR-19 BFGoodrich g-Force T/A KDW 2

http://i700.photobucket.com/albums/ww1/wpano/April-1-2009/1RearWheel-275-35-19.jpg
http://i700.photobucket.com/albums/ww1/wpano/April-1-2009/2RearWheel-275-35-19.jpg
http://i700.photobucket.com/albums/ww1/wpano/April-1-2009/4RearWheel-275-35-19.jpg

Here are the fronts 18 X 8 245/40ZR-18 BFGoodrich g-Force T/A KDW 2
http://i700.photobucket.com/albums/ww1/wpano/April-1-2009/FrontWheels.jpg

[skatinjay27]

those are my faviorate wheels!!!
they were the first set i wanted for the my car and even with all the other wheels I have seen and love everytime someone shows these i forget about all the rest!
are they the pro-touring(2 piece) or the mesh(3 piece)?


btw love the car!

[68/Camaro]

those are my faviorate wheels!!!
they were the first set i wanted for the my car and even with all the other wheels I have seen and love everytime someone shows these i forget about all the rest!
are they the pro-touring(2 piece) or the mesh(3 piece)?


btw love the car!

AJ,
Thanks for the Complement!
they are the pro-touring(2 piece) to look like the mesh! Thanks to Zak @ Boze

[tones2SS]

Car looks awesome!!!:thumbsup:

[DOOM]

:thumbsup: :yes: That looks awsome!!!!!!!!!!We Mounted the Front and Rear tires today
Rear 19 X 10 with 5.5 Backspacing and the 275/35ZR-19 BFGoodrich g-Force T/A KDW 2

http://i700.photobucket.com/albums/ww1/wpano/April-1-2009/1RearWheel-275-35-19.jpg
http://i700.photobucket.com/albums/ww1/wpano/April-1-2009/2RearWheel-275-35-19.jpg
http://i700.photobucket.com/albums/ww1/wpano/April-1-2009/4RearWheel-275-35-19.jpg

Here are the fronts 18 X 8 245/40ZR-18 BFGoodrich g-Force T/A KDW 2
http://i700.photobucket.com/albums/ww1/wpano/April-1-2009/FrontWheels.jpg

[68/Camaro]

Installing Unisteer complete rack and Steering Shaft w/Column Bearing from Speed Tech Performance
Blake and Roger are Great to work with! The Best customer service bar-none!!

http://i700.photobucket.com/albums/ww1/wpano/April-3-2009/Picture023.jpg
http://i700.photobucket.com/albums/ww1/wpano/April-3-2009/Picture021.jpg
http://i700.photobucket.com/albums/ww1/wpano/April-3-2009/Picture026.jpg

[68/Camaro]

Also Installing Clutch Master Cylinder from Keisler Engineering T-56 TKO-600 Kit
http://i700.photobucket.com/albums/ww1/wpano/April-3-2009/Picture014.jpg
http://i700.photobucket.com/albums/ww1/wpano/April-3-2009/Picture015.jpg

[68/Camaro]

Mock up the DSE Closeout panel!
http://i700.photobucket.com/albums/ww1/wpano/April-3-2009/Picture034.jpg

Tires Mounted and balanced check out the stance

http://i700.photobucket.com/albums/ww1/wpano/April-3-2009/Picture028.jpg


http://i700.photobucket.com/albums/ww1/wpano/April-1-2009/3RearWheel-275-35-19.jpg

[Vegas69]

Nice work...who painted the car?

[68/Camaro]

Nice work...who painted the car?

Hi Todd!
Tom Argue Owner of Tom Argue Design & http://www.hydroillusions.com/
The Best to Work With!!:thumbsup:

[tones2SS]

Car is looking way good.
I love those SW headers!!! The black paint and wheels go hand in hand.:thumbsup: :cheers:

[syborg tt]

Hi Todd!
Tom Argue Owner of Tom Argue Design & http://www.hydroillusions.com/
The Best to Work With!!:thumbsup:

You should some of the stuff this guy builds. He very quiet and keeps to himself but does incredible work.

[awr68]

Looking great!! :thumbsup:
I may have missed it, but are you using an iron block? What's the motor specs?

[68/Camaro]

Looking great!! :thumbsup:
I may have missed it, but are you using an iron block? What's the motor specs?
Anthony,
Lower End Block
LS-2
Bore and stroke: 4.00 x 3.62 in.
Displacement: 364 cu. in. (5.967 liters)
Compression: 10.9:1
Gross Horsepower (SAE net) 400 @ 6000 rpm
Gross Torque (SAE net) 400 lb.-ft. @ 4400 rpm
Block All-new 319-T5 Aluminum

Top Half is
Livernois Heads:
Stage 2 CNC Ported Stage 2 GM LS-Series Cylinder Heads
New GM 243 casting
5 axis CNC machined
220cc Intake Runner
Intake Flow Rate 305 CFM
Exhaust Flow Rate 235 CFM
2.000 intake valves / 1.550 exhaust valves
GM valve seals and locks
Livernois dual coil valve springs good to ~ .690 lift
Livernois titanium retainers.--Jessel 1.7 Rollor rockers

Livernois Motorsports LS-Series Stage 2 Camshaft
Intake Duration 232 @ .050
Exhaust Duration 232 @ .050
Intake Lift .595”
Exhaust Lift .595
LSA 114
Should be right @ 500HP

[awr68]

Thanks! That ought to work!! :unibrow: :thumbsup:

[Bakaruda]

Man the car looks great.

[customcam]

very Cool :thumbsup:

[Flash68]

Man that is a phenomenal build. Everything looks so damn clean and perfect!

Great pics. Thanks for sharing.

[68/Camaro]

Special Thanks to Tyler @ ATS he was able to get me a set of his Coil mounts! We installed them on the inside of the SpeedTech Subframe check out pics!
http://i700.photobucket.com/albums/ww1/wpano/March-27-2009/ATSCoilMounts.jpg
Drivers Side
http://i700.photobucket.com/albums/ww1/wpano/March-27-2009/DriveSideCoils.jpg

Pass-Side
http://i700.photobucket.com/albums/ww1/wpano/March-27-2009/PassSideCoils.jpg

Here it is Wired up!

http://i700.photobucket.com/albums/ww1/wpano/March-27-2009/IMG_1144.jpg

[tones2SS]

That looks awesome!!!:hail:

[HotRod68Camaro]

Love this build. Im wondering if i can make those coil mounts work on my C5. Those look sweet.

[68/Camaro]

Love this build. Im wondering if i can make those coil mounts work on my C5. Those look sweet.

Call Tyler @ American Touring Specialties
Phone: 702-245-6305

[67SS350]

The CF looks great on the black. Cant wait to see pictures of it complete as mine is black as well.

[waynieZ]

You have an awesome build . And what a sweet powerplant.

[1badchevelle]

Damm I hate seeing builds on this site. My wish list for my build just keeps getting longer.

Now I want some coil mounts.

Great build love the details you are adding.

[68/Camaro]

Tom is Installing and relocating Parking brake in the center side console along with cables

http://i700.photobucket.com/albums/ww1/wpano/May-28-2009/IMG_0127.jpg

http://i700.photobucket.com/albums/ww1/wpano/May-28-2009/IMG_0084.jpg

http://i700.photobucket.com/albums/ww1/wpano/May-28-2009/IMG_0087.jpg

Now Running the Fuel Line with new clips to hold looks like it's Floating along the under carrage

http://i700.photobucket.com/albums/ww1/wpano/May-28-2009/IMG_0076JPG-2.jpg

http://i700.photobucket.com/albums/ww1/wpano/May-28-2009/IMG_0104.jpg

[68/Camaro]

Special Thanks to Justin @ Wilwood was able to help us out to upgrade Calipers to the Six Piston
Rear
http://i700.photobucket.com/albums/ww1/wpano/May-28-2009/IMG_0102.jpg

http://i700.photobucket.com/albums/ww1/wpano/May-28-2009/IMG_0122.jpg

http://i700.photobucket.com/albums/ww1/wpano/May-28-2009/IMG_0121.jpg

Front

http://i700.photobucket.com/albums/ww1/wpano/May-28-2009/IMG_0099.jpg

Installing Brake Lines and proportioning valve

http://i700.photobucket.com/albums/ww1/wpano/May-28-2009/IMG_0080.jpg

http://i700.photobucket.com/albums/ww1/wpano/May-28-2009/IMG_0105.jpg

http://i700.photobucket.com/albums/ww1/wpano/May-28-2009/IMG_0082.jpg

[Vegas69]

Nice work as usual. That's not a very good place for the ebracke clevis and cables. It can get pretty tight in the tunnel under hard accel.

[68/Camaro]

A Sneak peak under the LS-2 Motor and Tremic Trans kit from Keisler Engineering

http://i700.photobucket.com/albums/ww1/wpano/May-28-2009/IMG_0094.jpg

Tom Finishing up Polishing the Speedtech-Stainlessworks Headers and Exhaust 3' X pipe to the mufflers and 2.5 Over the rear axle, Tom Custom cut so it would clear the Chris Alston's Rear link Suspension

http://i700.photobucket.com/albums/ww1/wpano/May-28-2009/IMG_0116.jpg

http://i700.photobucket.com/albums/ww1/wpano/May-28-2009/IMG_0110.jpg

http://i700.photobucket.com/albums/ww1/wpano/May-28-2009/IMG_0125.jpg

Look what else came in Ring Brothers New Hood Hinges Thanks Jim!

http://i700.photobucket.com/albums/ww1/wpano/May-28-2009/1238694116_6056910067_69_Camaro_blk.jpg

[syclonetommy]

Nice work as usual. That's not a very good place for the ebracke clevis and cables. It can get pretty tight in the tunnel under hard accel.


The clvis and cables will have a shrould that cover them in the top of the tunnel.

Thanks,
Tom Argue

[68/Camaro]

Tom is also finishing covering the wiring harness!

http://i700.photobucket.com/albums/ww1/wpano/May-28-2009/IMG_0119.jpg

[Spiffav8]

Awesome work! :thumbsup:

[Vegas69]

The clvis and cables will have a shrould that cover them in the top of the tunnel.

Thanks,
Tom Argue

Wouldn't work for me but I have mine fairly low in the back.

[tones2SS]

Car is looking good & coming along!:thumbsup:

[68/Camaro]

Just received the replacement glass from (Flush Mount Glass System) by Classic Auto Glass Innovations! Thanks to Robert the other glass was a test fit.

http://i700.photobucket.com/albums/ww1/wpano/May-28-2009/IMG_0131.jpg

http://i700.photobucket.com/albums/ww1/wpano/May-28-2009/IMG_0135.jpg

http://i700.photobucket.com/albums/ww1/wpano/May-28-2009/IMG_0137.jpg

[Blake Foster]

Looking Great Bill. Roger just got theflush mount glass for his also. be interesting to see how it fits. Hey those headers look KILLER where did you get those :thumbsup:

[68/Camaro]

Looking Great Bill. Roger just got theflush mount glass for his also. be interesting to see how it fits. Hey those headers look KILLER where did you get those :thumbsup:

humm..Take a guess hey they have the plate that say SpeedTech by Stainlessworks!:clap:

[Mrfixit]

Just received the replacement glass from (Flush Mount Glass System) by Classic Auto Glass Innovations! Thanks to Robert the other glass was a test fit.

http://i700.photobucket.com/albums/ww1/wpano/May-28-2009/IMG_0131.jpg

http://i700.photobucket.com/albums/ww1/wpano/May-28-2009/IMG_0135.jpg

http://i700.photobucket.com/albums/ww1/wpano/May-28-2009/IMG_0137.jpg

I love the idea of flush glass. I followed your earlier ling to Class Auto Glass Innovations but there was no contact information. Can you hook me up? I'm also working on a 68 Camaro and love the smooth and modern look of the flush glass.

[68/Camaro]

I love the idea of flush glass. I followed your earlier ling to Class Auto Glass Innovations but there was no contact information. Can you hook me up? I'm also working on a 68 Camaro and love the smooth and modern look of the flush glass.

PM Sent!

[68/Camaro]

We decided to use products from Heatshield Products covering the fuel lines with Black Colored Sleeve coatings make it capable of withstanding 1200°F continuous so we don't have vapor lock issues, Also covering the brake lines was a must take a look

http://i700.photobucket.com/albums/ww1/wpano/June-4-2009/IMG_0156.jpg

http://i700.photobucket.com/albums/ww1/wpano/June-4-2009/IMG_0160.jpg

http://i700.photobucket.com/albums/ww1/wpano/June-4-2009/IMG_0158.jpg

Rear Brake Lines

http://i700.photobucket.com/albums/ww1/wpano/June-4-2009/IMG_0154.jpg
Plastic stand offs
http://i700.photobucket.com/albums/ww1/wpano/June-12-2009/quickclip.png

http://i700.photobucket.com/albums/ww1/wpano/June-4-2009/IMG_0144-1-1.jpg
Rear Braided Brake Lines
http://i700.photobucket.com/albums/ww1/wpano/June-4-2009/IMG_0143.jpg

http://i700.photobucket.com/albums/ww1/wpano/June-4-2009/IMG_0147.jpg

[68/Camaro]

Gas Tank in!

http://i700.photobucket.com/albums/ww1/wpano/June-4-2009/IMG_0153.jpg

http://i700.photobucket.com/albums/ww1/wpano/June-4-2009/IMG_0177.jpg

[68/Camaro]

Wouldn't work for me but I have mine fairly low in the back.

Tom Custom made a shroud that covers the clvis and cables in the top of the tunnel.


http://i700.photobucket.com/albums/ww1/wpano/June-4-2009/IMG_0150.jpg

[68/Camaro]

Finishing installing front braided brake lines and hard line, Also installing the Safety Wire on Wilwood Rotors and Calipers

http://i700.photobucket.com/albums/ww1/wpano/June-4-2009/IMG_0162.jpg

http://i700.photobucket.com/albums/ww1/wpano/June-4-2009/IMG_0164.jpg

http://i700.photobucket.com/albums/ww1/wpano/June-4-2009/IMG_0165.jpg

http://i700.photobucket.com/albums/ww1/wpano/June-4-2009/IMG_0166.jpg

http://i700.photobucket.com/albums/ww1/wpano/June-4-2009/IMG_0167.jpg

http://i700.photobucket.com/albums/ww1/wpano/June-4-2009/IMG_0171.jpg

[Vegas69]

I hope you don't think I'm bashing your project. Let's call it constructive criticism. Great idea on the heat insulators. I'm gettting ready to use it in some places as well.

[68/Camaro]

I hope you don't think I'm bashing your project. Let's call it constructive criticism. Great idea on the heat insulators. I'm gettting ready to use it in some places as well.
Todd Not at All, we all need constructive criticism to help each other out.
The Heat products are awesome!

[bmwwksmarc]

Great attention to detail, love the little things like the plastic stand offs for the fuel lines.
Just noticed your front calipers are reversed.Bleed screws need to be on the top.

Marc

[syclonetommy]

Great attention to detail, love the little things like the plastic stand offs for the fuel lines.
Just noticed your front calipers are reversed.Bleed screws need to be on the top.

Marc



Thank you, Marc

Wilwood installed bleeds @ both top and botton of the product.


Tom Argue

[bmwwksmarc]

Thanks for setting me straight Tom, you can't see the tops in the pics. We've used a ton of them in our BMW hot rods and the calipers I get have the balance tube on one end.

Marc

[68/Camaro]

Tom finishing installing the Tank from Ricks Tanks! and the single line fuel filter regulator on a custom bracket that Tom made on the tank

http://i700.photobucket.com/albums/ww1/wpano/June-12-2009/IMG_0189.jpg

http://i700.photobucket.com/albums/ww1/wpano/June-12-2009/IMG_0179.jpg

http://i700.photobucket.com/albums/ww1/wpano/June-12-2009/IMG_0187.jpg

http://i700.photobucket.com/albums/ww1/wpano/June-12-2009/IMG_0180.jpg

http://i700.photobucket.com/albums/ww1/wpano/June-12-2009/IMG_0191.jpg


Received the drive shaft and installed with the safety loop

http://i700.photobucket.com/albums/ww1/wpano/June-12-2009/IMG_0192.jpg

http://i700.photobucket.com/albums/ww1/wpano/June-12-2009/IMG_0184.jpg

[Vegas69]

Tom is doing some killer work for you. I like the brushed tank.;)

[68/Camaro]

Painted the Diff Cover black looks better!

http://i700.photobucket.com/albums/ww1/wpano/June-12-2009/IMG_0199.jpg

[68/Camaro]

Tom is doing some killer work for you. I like the brushed tank.;)

Thanks Todd, Tom is Awesome! also he decided to brushed tank what a surprise!

[68/Camaro]

Plastic Stand offs are in the front brake lines (Received them from Joe McCullough) They can be purchased from kdhotrods.com

http://i700.photobucket.com/albums/ww1/wpano/June-12-2009/quickclip.png


http://i700.photobucket.com/albums/ww1/wpano/June-12-2009/IMG_0196.jpg

[tones2SS]

She must be nearing completion now.
Looks great.:thumbsup:

[syclonetommy]

She must be nearing completion now.
Looks great.:thumbsup:

Completion date is near!

We have a shop dead line of 13 Days( Sorry no youtube vid)or up to the min pic's.

I keep telling Bill I'm going to lock him out of the shop, He's going to have see the car complete @ the Good Guys show.:lol:



Tom

[Flash68]

yeah dude that brushed tank looks fantastic. Makes me wanna do that! Nice work.

[68/Camaro]

Well as of yesterday 4:30 pm project "Evade" has a pulse.

Hopefully Today she comes Alive!:dance:


Tom Argue

[tones2SS]

VERY COOL!!!:thumbsup: :cheers:

[patriot68]

we need video of it running/driving:thumbsup:

[68/Camaro]

Many Thanks to Jim @ StainlessWorks to help us with the exhaust system, Tom Custom made the tail pipes to run through the new Chris Alston's G-Bar rear suspension! Also Steve Heye from Heat Shield Products was able to hook us up with there Lava Wrap Tom wrap the tail pipes so we would not have any issues with vapor lock. Check it out!

http://i700.photobucket.com/albums/ww1/wpano/June-18-2009/IMG_0201.jpg

http://i700.photobucket.com/albums/ww1/wpano/June-18-2009/IMG_0202.jpg

http://i700.photobucket.com/albums/ww1/wpano/June-18-2009/IMG_0204.jpg

http://i700.photobucket.com/albums/ww1/wpano/June-18-2009/IMG_0206.jpg

http://i700.photobucket.com/albums/ww1/wpano/June-18-2009/IMG_0210.jpg

[68/Camaro]

BTW SHE IS ALIVE!!!! :willy:

[Hdesign]

Congrats Bill.....you've gotta be pumped!!!!:thumbsup:

[68/Camaro]

Here is "Evade"s first start! sorry my video camera is on the frits

http://www.youtube.com/watch?v=ZFhe6qjdua8

http://www.youtube.com/watch?v=s-Th918Qmw0

[tones2SS]

Very nice.
You must be stoked!!:thumbsup: :cheers:

[waynieZ]

Very Nice

[awr68]

Love it!! :thumbsup:

[syborg tt]

Awesome undercarriage ya got there.

Can't wait to watch the video of the motor running. DSL is still down, Dial up is killling me.

[68/Camaro]

He Guys! Project "Evade" in July's Camaro Performers magazine page 13 check it out! Many Thanks to Ben Hermance, Nick and Steve from Camaro Performers

http://i700.photobucket.com/albums/ww1/wpano/Camaro%20Performers/FridayJuly032009.jpg

http://i700.photobucket.com/albums/ww1/wpano/Camaro%20Performers/FridayJuly0320092.jpg

[68/Camaro]

Roger from Speed Tech was able to get Paul that works with him to get this sign made for us for the Goodguys show in Columbus O.H.

http://i700.photobucket.com/albums/ww1/wpano/Camaro%20Performers/EVADE-FINAL.jpg

[68/Camaro]

Guy's Sorry no more pics!
"Evade" will debut @ the Goodguy's show in Columbas O.H. July 10-12th
@ Stainlessworks booth!!!

http://i700.photobucket.com/albums/ww1/wpano/Camaro%20Performers/swnewlogosmall.jpg

[awr68]

That's awesome!! Congrats!! Can't wait to see the final pics!!
I just picked up a couple more CP mags last night!
Have a great time at the show!! :cheers: :thumbsup: :woot:

[syborg tt]

Hi Bill,

Car is looking great. So are you going to let out your little secret. When I talked to hom tbhis morning he was in Nashville and said he would be in tonight.

[68/Camaro]

Hi Bill,

Car is looking great. So are you going to let out your little secret. When I talked to hom tbhis morning he was in Nashville and said he would be in tonight.

Marty,
Tom told me not say anything yet until Columbus :censored:

[tones2SS]

VERY AWESOME!:thumbsup:
That is cool. Car looks great as does the rendering. Ben does some GREAT work. We were hanging out yesterday & today @ the Summer Nats in Worcester.
CONGRATS!!:cheers:

[syborg tt]

Marty,
Tom told me not say anything yet until Columbus :censored:

cool - just make sure you get pics, lots of them

ps - see ya in columbus

[Blake Foster]

Wish we could be there to see it in person............. maybe you should bring it to Washington i mean it's only a 4 day drive, it could be a good shake down drive, and besids we have drag racing at the good guys meet here.just for the hell of it..... why is it that the west coast guys always gotta do the traveling anyway????:mad:

Good luck Bill
glad you got it done in time and have fun say hi to the SW guys for us

[70rs]

Incredible car! That exhaust alone is a work of art, let alone the rest of the car.:thumbsup:

Congrats on the ink in CP!

[syborg tt]

Wish we could be there to see it in person............. maybe you should bring it to Washington i mean it's only a 4 day drive, it could be a good shake down drive, and besids we have drag racing at the good guys meet here.just for the hell of it..... why is it that the west coast guys always gotta do the traveling anyway????:mad:

Good luck Bill
glad you got it done in time and have fun say hi to the SW guys for us

Not to worry I will take a bunch of pics for you Killer.

So why do you west coast guy's have to travel - Cause you guy's have more money then us.....

[68/Camaro]

Hi Bill,

Car is looking great. So are you going to let out your little secret. When I talked to hom tbhis morning he was in Nashville and said he would be in tonight.

Ok The secret was that The man behind all the Big Builds came to Fl is Bob Thrash! To lay out the design for Evade!

http://i700.photobucket.com/albums/ww1/wpano/July-7-8-2009/IMG_0317.jpg

http://i700.photobucket.com/albums/ww1/wpano/July-7-8-2009/IMG_0322.jpg

http://i700.photobucket.com/albums/ww1/wpano/July-7-8-2009/IMG_0303.jpg

[70rs]

More money for the west coast guys.....:rofl: you are killing me!
The car is looking incredible! Can't wait to see more. Thanks for posting.

[68/Camaro]

Project "Evade" is on its way to Columbus for the GoodGuy's Show!!!

http://i700.photobucket.com/albums/ww1/wpano/July-7-8-2009/IMG_0399.jpg

http://i700.photobucket.com/albums/ww1/wpano/July-7-8-2009/IMG_0393.jpg

[tones2SS]

That '68 looks KILLER! Hood & trunk look awesome.:thumbsup: :cheers:

[syborg tt]

Looks really nice. I can't wait to see it on Friday

[Hdesign]

Well deserved Bill! Enjoy! I wish I could make it out to Columbus to see it in person. Have a great time!:thumbsup:

[slck6t9]

VERY nice!!! The hood scheme looks similar to Larry's Motiv8r. I like it..

[phillym5]

I love the hood!! Nice work!!

[Hdesign]

Scott, that was the challenge for me. I did Rupp's Track Rat, Larry's MotiV8r and Bill's car. They all had the same CF parts and Bill really liked the others but wanted something different. We wanted to be sure to show off all the CF parts in a way that graphically worked with the car. The red stripe is actually the reverse of Larry's where the "tabs" kick out rather than kick in.

[tones2SS]

Scott, that was the challenge for me. I did Rupp's Track Rat, Larry's MotiV8r and Bill's car. They all had the same CF parts and Bill really liked the others but wanted something different. We wanted to be sure to show off all the CF parts in a way that graphically worked with the car. The red stripe is actually the reverse of Larry's where the "tabs" kick out rather than kick in.

Looks good Ben. Another job well done.:cheers:

[bigtyme1]

Bill, the car turned out great, I was lucky enough to Meet Bill this weekend and check out the car in Person at Columbus. Sorry we couldnt have spend more time togethor. that place was crazy.

[nvr2fst]

Project well done Bill. It looked great and your 1st time autox was pretty dam good. Congrats again.
Dave

[ccracin]

Hey Bill,

Great showing this weekend. It was truly a pleasure meeting and talking with you. Ben did a great job and you guys did an even better job bringing the rendering to life. You have alot to be proud of. Oh, and it didn't look like you took it real easy on the auto-x. I guess when the adrenaline gets flowing you can't help it. Congratulations.

[ANVIL1]

I finally met Bill in person in Columbus after talking to him many times on the phone. Real nice guy and his car turned out great! It was my first time at the Columbus Goodguys show even though I grew up in Ohio. Huge show with a lot of great cars, but Bill's car definitely garnered a lot of attention. Congrats Bill and great job Tom!

[Musclerodz]

Bill , car looked great. Sorry I missed you at the show. I looked for you but missed you a couple times.

[68/Camaro]

Bill , car looked great. Sorry I missed you at the show. I looked for you but missed you a couple times.

Mike Sorry i missed you!

[68/Camaro]

Well Guys here is Evade in Columbus @ they Goodguys Show! Special Thanks to Stainlessworks! Wow what a blast we had it was a pleasure to meet and talk to everyone there !! enjoy pics!

http://i700.photobucket.com/albums/ww1/wpano/Goodguys%20O%20H%20Show/IMG_0520.jpg

http://i700.photobucket.com/albums/ww1/wpano/Goodguys%20O%20H%20Show/IMG_0426.jpg

http://i700.photobucket.com/albums/ww1/wpano/Goodguys%20O%20H%20Show/IMG_0428.jpg

http://i700.photobucket.com/albums/ww1/wpano/Goodguys%20O%20H%20Show/IMG_0390.jpg

http://i700.photobucket.com/albums/ww1/wpano/Goodguys%20O%20H%20Show/IMG_0421.jpg

[68/Camaro]

Taking off to go to the Autocross!

http://i700.photobucket.com/albums/ww1/wpano/Goodguys%20O%20H%20Show/IMG_0476.jpg

http://i700.photobucket.com/albums/ww1/wpano/Goodguys%20O%20H%20Show/IMG_0478.jpg

http://i700.photobucket.com/albums/ww1/wpano/Goodguys%20O%20H%20Show/IMG_0479.jpg

[SickSpeedMonte]

That thing is sharp!

[tones2SS]

That is a beautiful car Bill.
LOOKS KILLER!:thumbsup: :cheers:

[Vegas69]

Very nice....and now the best part. Driving!

[wedged]

got any more pics of the black road runner parked next to you ?

[Mrfixit]

Wow! Can you tell me more about the center console? What an awesome car. Fantastic job all around. :hail:

http://i700.photobucket.com/albums/ww1/wpano/Goodguys%20O%20H%20Show/IMG_0390.jpg

[70rs]

The car turned out incredible!

[68/Camaro]

[QUOTE=Mrfixit;222931]Wow! Can you tell me more about the center console? What an awesome car. Fantastic job all around. :hail:

Tom Argue Custom made the center console it came from 04-06 GTO we will be offering a custom fit for 67-68 Camaros soon if there are any interests out there let us know!
Thanks, Bill

[68/Camaro]

got any more pics of the black road runner parked next to you ?

PM me your e-mail

[wedged]

PM sent - Thanks !

[Rybar]

Wow man, this car turned out awesome! Great attention to the details, very well done! :thumbsup:

[redfire69]

X2, totally wicked!! Is that a CF radiator close-out?

Wow man, this car turned out awesome! Great attention to the details, very well done! :thumbsup:

[68/Camaro]

X2, totally wicked!! Is that a CF radiator close-out?

Many Thanks for the complements guys!
The close out panel is from DSE, Tom Argue has a special paint process that he did to give the CF look the same with the Intake and the Valve covers!
Thanks, Bill

[68/Camaro]

My first Autocross with "Evade" Wow what an experience didn't do to bad although #1 did not get a chance to dial in the motor #2 did not get a chance to align the car but here are the times "Evade" ran , Bill – 1968 Camaro – Lap Times 39.579, 36.457, 36.081 the third lap she drifted on me What a Blast!!! Met with Steve Rupp many thanks Steve for the conversations we had! I found these shots on http://www.hotrodhotline.com/feature/2009show/09ggcolumbusaljuly10/html/page_8.php

http://i700.photobucket.com/albums/ww1/wpano/AutoCross-03/db_GG_NATS_F_S_09__632_1.jpg

http://i700.photobucket.com/albums/ww1/wpano/AutoCross-03/db_GG_NATS_F_S_09__633_1.jpg

[syborg tt]

here is the Mad Man with the plan and the car

http://www.garagescene.net/gallery2/d/39301-2/2009+07-10+GG+Columbus+384.JPG

http://www.garagescene.net/gallery2/d/39337-2/2009+07-10+GG+Columbus+396.JPG

http://www.garagescene.net/gallery2/d/39340-2/2009+07-10+GG+Columbus+397.JPG

[tones2SS]

[QUOTE=syborg tt;223348]here is the Mad Man with the plan and the car

http://www.garagescene.net/gallery2/d/39301-2/2009+07-10+GG+Columbus+384.JPG

Lucky man!! Love that color combo. AWESOME!:bow: :cheers:

[nvr2fst]

[QUOTE=syborg tt;223348]here is the Mad Man with the plan and the car

http://www.garagescene.net/gallery2/d/39301-2/2009+07-10+GG+Columbus+384.JPG

Lucky man!! Love that color combo. AWESOME!:bow: :cheers:

Bill I see your not sweating in this picture!
Either you got the car handled or the temps were finally going down. Great job again and nice talking to ya!
Dave

[syclonetommy]

Many Thanks for the complements guys!
The close out panel is from DSE, Tom Argue has a special paint process that he did to give the CF look the same with the Intake and the Valve covers!
Thanks, Bill

Go To: www.hydroillusions.com for more info.

Thanks,
Tom Argue

[fleet]

My congrats on how well your car turned out. :thumbsup:

When you get a chance, I think posting some closeup pics of the interior, especially the console, would be of a lot of interest here.

[camaro2nv]

More pics! Very nice job on the car!

[Bozeforged]

Hey Bill,



I just posted your car on our blog. Check it out at:



http://www.bozeforged.com/blog/



Zak

[68/Camaro]

Hey guys Check out the Septembers Issue of Camaro Performers Magazine! Thanks to Ben Hermance wrote am article and "Evade" the Rendering covers two pages 16 and 17! It Looks Wicked! Thanks Nick, Steve and Ben!

http://i700.photobucket.com/albums/ww1/wpano/Camaro%20Performers/CamaroPerformers-Sept-09.jpg

[redfire69]

Congrats again on the press. What a well thought out car from concept to reality! :thumbsup:

[tones2SS]

VERY COOL! Congrats. Car is looking good.:cheers:

[68/Camaro]

Hey guys! sorry its been a while posting but we have been busy touching up minor things on "Evade" we got her on the Dyno last week! with a Great help from Jeremy Formato with Fasterproms!
Here are some Pictures will post the updated Video! next thread


http://i700.photobucket.com/albums/ww1/wpano/Dyno%20Pics/200909051423462.jpg

http://i700.photobucket.com/albums/ww1/wpano/Dyno%20Pics/200909051340111.jpg

http://i700.photobucket.com/albums/ww1/wpano/Dyno%20Pics/200909051411251.jpg

http://i700.photobucket.com/albums/ww1/wpano/Dyno%20Pics/200909051339391.jpg

http://i700.photobucket.com/albums/ww1/wpano/Dyno%20Pics/200909051338282.jpg

http://i700.photobucket.com/albums/ww1/wpano/Dyno%20Pics/200909051448331.jpg

http://i700.photobucket.com/albums/ww1/wpano/Dyno%20Pics/200909051448332.jpg

[awr68]

Great looking car!! :thumbsup:

[68/Camaro]

"Evade" we got her on the Dyno last week! with a Great help from Jeremy Formato with Fasterproms to Dial here in!
Check out the Video! Crank it up!

http://www.youtube.com/watch?v=nNxomMuiTZQ

[70rs]

Sounds awesome! Nice power too. Beautiful car.:hail:

[tones2SS]

Great looking car!! :thumbsup:

I agree with Tony. That is a gorgeous car. I think that's the first time I've seen the engine bay and it is nice and clean. Looks awesome!:thumbsup:

[nvr2fst]

Bill
Good to here the update. Nothing like taking a finished car to the Dyno.
So whats next for this sweet ride.

[thedugan]

what taillights are those?

[syborg tt]

Bill - Tom the car looks awesome.

ps I could use some Aguafina right now

[68/Camaro]

what taillights are those?

Doug,
The Taillights are Marquez Design

[68/Camaro]

Bill - Tom the car looks awesome.

ps I could use some Aguafina right now

Marty,
Here is a Bottle in Attached picture
http://i700.photobucket.com/albums/ww1/wpano/Dyno%20Pics/200909051430031.jpg

Dyno Run:
http://www.youtube.com/watch?v=nNxomMuiTZQ

[68/Camaro]

Here are the Dyno Sheets for HP and Torque also look @ the Temps! the 5th run we ended up with 430.25hp @ the rear wheels and the Temp was @ 99.51-Degrees !

http://i700.photobucket.com/albums/ww1/wpano/Dyno%20Pics/DYNOMAXHP.jpg

http://i700.photobucket.com/albums/ww1/wpano/Dyno%20Pics/DYNOMAXTORQUE.jpg

[speedshftr]

very sweet car you have there/from a few pics the hood looks as if it needs adjusting?the car is really an eye catcher and i hope mine turns out half as nice.im also running the flush mount glass from robert.how did the install of the glass go?im interested in a console from you guys.can you give me some specs on it/price options ect.
thanks and hats off for a awsum ride/:hail: :hail:

[68/Camaro]

very sweet car you have there/from a few pics the hood looks as if it needs adjusting?the car is really an eye catcher and i hope mine turns out half as nice.im also running the flush mount glass from robert.how did the install of the glass go?im interested in a console from you guys.can you give me some specs on it/price options ect.
thanks and hats off for a awsum ride/:hail: :hail:

Thanks for the comment!
The hood is ok now and adjusted, the Flush Mount Glass is Great! I would recommend have a Professional Auto Glass Installer to Install it will make it a breeze. As far as the console Tom is working on a proto type will keep you posted.
Thanks Again
Bill

[tones2SS]

Such an awesome car Bill.
ENJOY!!:thumbsup:

[GMracer]

this car is stunning :thumbsup:

[68/Camaro]

Special Thanks to Blake and Roger from Speedtech Performance!:bow:
"Evade" will be at SEMA!!

[tones2SS]

Special Thanks to Blake and Roger from Speedtech Performance!:bow:
"Evade" will be at SEMA!!

VERY COOL!!!:cheers:

[awr68]

Special Thanks to Blake and Roger from Speedtech Performance!:bow:
"Evade" will be at SEMA!!

Nice!! Can't wait to see it!! Will it be in the booth or main hall?

[Flash68]

Awesome man! Congrats!

[68/Camaro]

Nice!! Can't wait to see it!! Will it be in the booth or main hall?
Anthony,
Dont know yet?

[68/Camaro]

Special Thanks to Jim & Staci here are the Door Handles Installed on "Evade" Tom Polished Handles and beed Blasted the Outer piece & Button! --> Heading for SEMA!

http://i700.photobucket.com/albums/ww1/wpano/New%20Products%20October-27-2009/IMG_1364.jpg
http://i700.photobucket.com/albums/ww1/wpano/New%20Products%20October-27-2009/IMG_1366.jpg
http://i700.photobucket.com/albums/ww1/wpano/New%20Products%20October-27-2009/IMG_1357.jpg

[68/Camaro]

Tom Installed the Clayton Machine Works New Pedals!! Thanks Clay and Ron from Hood Pins

http://i700.photobucket.com/albums/ww1/wpano/New%20Products%20October-27-2009/IMG_1347.jpg
http://i700.photobucket.com/albums/ww1/wpano/New%20Products%20October-27-2009/IMG_1345.jpg

[tones2SS]

Those pedals are awesome.:thumbsup:

[redfire69]

Looks like you're getting the first of 2 more killer parts!:thumbsup:

[Blake Foster]

that thing should be in a trailer by now!!!!

see you saturday cant wait to see the car in person and then drive it on saturday!! hahaha to the optima challange
should be a fun drive:unibrow:

[syclonetommy]

that thing should be in a trailer by now!!!!

see you saturday cant wait to see the car in person and then drive it on saturday!! hahaha to the optima challange
should be a fun drive:unibrow:

Its in the trailer
You need to drive the wheels off it!!!!

just keep it out of the cones.

I'll see you guys on Tues.

Tom

[68/Camaro]

GREAT JOB BILL....BRAVO!!!!

When you get a moment email some pics of that beast...

Thanks
Gus

Hey Gus!
Check out "Camaro Performers" December Issue Black is Back (Seven Page spread of "Evade" Pages 78-84

http://i700.photobucket.com/albums/ww1/wpano/Camaro%20Perf-Dec-2009/CAMPSEPTCN1.jpg

[Tony722]

Wow!!! beautiful spread...Car is very well done. nice attention to detail. engine compartment is all business. Can you disclose how you did the intake tube? very impressive!!!!!

[tones2SS]

Very cool. That car is killer.
Congrats on the magazine spread.:thumbsup: :cheers:

[PASD U]

Man, how did I miss this one??! Everybody has said it all. Very nice 68. One question I didn't see covered though, what mirrors are those?

[68/Camaro]

Man, how did I miss this one??! Everybody has said it all. Very nice 68. One question I didn't see covered though, what mirrors are those?

Thanks for the comment the mirror is a stock base with a Billet Specialties Mirror
Bill P

[68/Camaro]

Here is an ad that just came out on the news stand in Hot Rod Magazine March Issue

http://i700.photobucket.com/albums/ww1/wpano/Tremic%20Trans%20Ad%20and%20Vintage%20Air%20Ad/TREMEC_HotRod_0310.jpg

[tones2SS]

Here is an ad that just came out on the news stand in Hot Rod Magazine March Issue

http://i700.photobucket.com/albums/ww1/wpano/Tremic%20Trans%20Ad/TREMEC_HotRod_0310.jpg

BAD ASS!!!
Congrats. That is a sweet car.:thumbsup: :cheers:

[GregWeld]

Sweet Bill!!

EEEEEEEEEEHHHHHHHHAAAAAAAAAAAAAA
:woot:

[awr68]

Very cool Bill and Tom! That car is very nice and adds like this are very well deserved!!

It was great talking with you two daily at SEMA!! :thumbsup: :cheers:

[68/Camaro]

Winter National 2010 Hosted by Classic Camaro of Central Florida!

I didn’t think we would make it as of last week on Tuesday Tom Argue’s Baby Daughter went to the hospital having breathing difficulty with a viral infection I told Tom listen your family is more important we do not have to go! But Tom was insisted and said don’t worry my wife will be at the hospital I’ll get “Evade” there….He said the car Must be there!! I drove over early Thursday afternoon and Tom left Thursday night from the hospital Trailerd the car and made to Coco beach @ 1 AM! Friday We got up Friday morning very little sleep unloaded the car and @ 6:30 in the morning Tom left the trailer and headed back to St. Pete at the hospital my thoughts and prayers were with them! In is absent from the show Tom sent one of is employee’s over to help me with the show! Finally on Saturday his daughter was released from the hospital and is doing well Thank God! Tom Argue is dedicated to his customers 100% I will never forget this! I feel like part of the Argue family! Many Thanks Tom & Susan! "Tom Argue Design"


Eckler’s Chevy Classics and Worldwide Camaro Club took it to the Coco beach!
Winter National 2010 Hosted by Classic Camaro of Central Florida!
I think there were almost 300 cars there! This was a 1000 point judging 3 judges tearing apart and going all over the car! Body exterior, Paint, Engine & Engine compartment, Driveline & Suspension, Under carriage, Trunk & Cargo area, Wheels & Tires!
First 25 points (Tech-Check) are judged in a tech inspection looking for everything that is working! Head lights, high beams, turn signals, flashers, in the dash indicators, brake lights, back up lights, lic-plate light, dome light, pwr windows, cigar lighter and glove box light ect.

All said and done Project “Evade” Won (4) Awards! @ The 18th Annual Winter National and scored “995”

# (1) Award "Trailered Custom Camaro 68" –Platinum Certificate Points 995 out of 1000
# (2) Award "Best Engine Modified/Custom"
# (3) Award "People’s Choice Show “N” Shine"
# (4) Award "Car That World Wide Camaro Would Most Like To Drive Home"


See below Certificate and Awards!
http://i700.photobucket.com/albums/ww1/wpano/Awards-18th%20Annual%20Winter%20National%20Coco%20Beach/PlatinumCert-995.jpg

Awards
http://i700.photobucket.com/albums/ww1/wpano/Awards-18th%20Annual%20Winter%20National%20Coco%20Beach/IMG_0723.jpg

Many Thanks to Tom! with "Tom Argue Design" your the best!!!

[ANVIL1]

Congrats Bill! Even better, I'm glad Tom's daughter is doing better. I have a little girl myself, and I would be beside myself if she was in the hostpital. Tom is definitely dedicated to his craft and a detail oriented and talented builder! :hail:
As an aside, I have family in Cocoa Beach, had I known your car was going to be there, I would have called them and had them go to the show.

[syborg tt]

Awesome - could'nt happend to a better group of guys.

[ProdigyCustoms]

Bill carried the torch for the Pro Touring movement. The show promoters loved the car and rewarded him for it.

Nice car, nice guy, way to go man.

995 at the WInter Nationals is some serious **** right there.

[cdushane]

I saw this car last month at Cars & Coffee and I have to say it's really a nice car! A lot of attention to detail was put into this one :thumbsup: Congrats on your awards!

[68/Camaro]

Bill carried the torch for the Pro Touring movement. The show promoters loved the car and rewarded him for it.

Nice car, nice guy, way to go man.

995 at the WInter Nationals is some serious **** right there.

Hey Frank Thanks for your kind words! It was great to see you and hang out!
BTW After the second Award he was announcing (68-Black Pro-Touring Camaro):dance:

[BonzoHansen]

Your car is great and deserves all that recognition. I think I drooled on it every day at SEMA.

It's so nice I won't even bust your rocks on the one in the lower LH corner. :)

[waynieZ]

Congratulation's , Beautiful car and awesome work.

[tones2SS]

Congrats!!!
Very nice. That car deserves all the awards it gets.:thumbsup:

[DOOM]

Bill... Way to go !!! Tom you to , You put together a bad azz automobile!!:hail: :cheers:

[formula98]

Way to go Bill, Tom, you guys deserve the awards! The Evade Camaro is one of the best I've seen. I'm really happy to see you guys get awards for your efforts. Great work!

[awr68]

Way to go guys! :thumbsup: :cheers:

[Chicken Louie]

Congrats on the recent awards!! One of my favorite builds!!:thumbsup:

[68/Camaro]

Hey everyone! its been awhile but I have a few changes and updates on Evade I will be posting soon!
I have a new website!:dance: www.evadecamaro.com please enjoy!
special Thanks to Adam with Revolution Industries, Fuel Injected Media www.rev-in.com

[tones2SS]

Very nice. Just checked out the website. Looks great.
That engine bay looks very clean.:yes:

[bigtyme1]

Great Job on the Web Sight. I'm hoping to do one myself one day.

[syborg tt]

special Thanks to Adam with Revolution Industries, Fuel Injected Media www.rev-in.com

hey i know this guy

[68/Camaro]

Hey everyone! its been awhile
Well this year "Evade" was no trailer Queen it was Driven at the Ecklers Winter National
Ecklers Winter National 2011 Hosted by Classic Camaro of Central Florida!
It was a great drive left on Friday morning little foggy and light rain on and off but the rest of the show weather turned out for the best!

Eckler’s Chevy Classics and Worldwide Camaro Club held in Orlando this year at the Westgate Resort!
I think there were almost 250 Plus cars there! This was a 1000 point judging 3 judges tearing apart and going all over the car! Body exterior, Paint, Engine, Engine compartment,Interior, under carriage and truck!
First 25 points (Tech-Check) are judged in a tech inspection looking for everything that is working! Head lights, high beams, turn signals, flashers, in the dash indicators, brake lights, back up lights, lic-plate light, dome light, pwr windows, cigar lighter and glove box light ect.

All said and done Project “Evade” Won (5) Awards! @ The 19th Annual Winter National and scored “984” Platinum Certificate

# (1) Award "Custom Driven Camaro 68" –Platinum Certificate Points 984 out of 1000
# (2) Award "Best Engine Modified/Custom"
# (3) Award "Best Interior Modified/Custom"
# (4) Award "People’s Choice Show “N” Shine"
# (5) Award "Car That World Wide Camaro Would Most Like To Drive Home"

See below Certificate and Awards!
http://i700.photobucket.com/albums/ww1/wpano/2011%20Ecklers-WinterNationals/Platnum-Cert-Wnternats-2011copy.jpg

http://i700.photobucket.com/albums/ww1/wpano/2011%20Ecklers-WinterNationals/Awards-Wnternats-2011copy.jpg

[syborg tt]

That's pretty Cool - Bill

[waynieZ]

Thats great congratulation's

[tones2SS]

Congrats Bill. Great car.

[Hdesign]

Way to go Bill, you deserve it bud!:thumbsup:

[Flash68]

Wow nice accolades. Congrats!

[bigtyme1]

Congrats Bill :cheers:

[awr68]

Congrats Bill! That's awesome and well deserved!! :thumbsup: :cheers:

[killer67]

Well deserved awards :thumbsup:

[phillym5]

Very cool... Hope you have plenty of wall space to hang all those.:captain:

[Forgeline 1]

Congratulations Bill!
Awesome car and well deserved awards. Thanks for letting Forgeline be a part of it.

Scott Main
Forgeline Motorsports
800-886-0093
www.forgeline.com

[syborg tt]

I'm telling you it had to be those forgeline wheels that put the car over the top

Congratulations Bill!
Awesome car and well deserved awards. Thanks for letting Forgeline be a part of it.

Scott Main
Forgeline Motorsports
800-886-0093
www.forgeline.com

[syborg tt]

So where are the picture of this fine car

[68/Camaro]

Ok here is a couple shots of the wheels and car I will get new shots of the car this week!

http://i700.photobucket.com/albums/ww1/wpano/Evade%20Updates%20Forgeline%20Wheels/IMG_0026-A-1.jpg
http://i700.photobucket.com/albums/ww1/wpano/Evade%20Updates%20Forgeline%20Wheels/IMG_0018.jpg
http://i700.photobucket.com/albums/ww1/wpano/Evade%20Updates%20Forgeline%20Wheels/IMG_0024JPG-A-1.jpg

http://i700.photobucket.com/albums/ww1/wpano/Evade%20Updates%20Forgeline%20Wheels/IMG_0079.jpg

[68/Camaro]

Here is the Trunk finished with all JL Audio that Tom Installed

http://i700.photobucket.com/albums/ww1/wpano/Evade%20Updates/IMG_0115JPG2.jpg
http://i700.photobucket.com/albums/ww1/wpano/Evade%20Updates/IMG_0056.jpg
http://i700.photobucket.com/albums/ww1/wpano/Evade%20Updates/IMG_0059.jpg
http://i700.photobucket.com/albums/ww1/wpano/Evade%20Updates/IMG_0057.jpg

http://i700.photobucket.com/albums/ww1/wpano/Evade%20Updates/IMG_0100.jpg
http://i700.photobucket.com/albums/ww1/wpano/Evade%20Updates/IMG_0097.jpg

[68/Camaro]

Here is the Side Marker Bezels from Marquez Design in Black Anodized

http://i700.photobucket.com/albums/ww1/wpano/IMG_0018JPG-1A.jpg
http://i700.photobucket.com/albums/ww1/wpano/IMG_0021JPG-1A.jpg

[speedfreak]

Lookin real nice Bill ! Congrats on all the awards ! :thumbsup:


Brian

[tones2SS]

Looks great Bill. Awesome car.:cheers:

[68/Camaro]

Here are a couple of updated pics of "Evade"
http://i700.photobucket.com/albums/ww1/wpano/Evade-Updated%20Photo-02-18-2011/IMG_0122JPGa-1.jpg
http://i700.photobucket.com/albums/ww1/wpano/Evade-Updated%20Photo-02-18-2011/IMG_0030JPGa-1.jpg
http://i700.photobucket.com/albums/ww1/wpano/Evade-Updated%20Photo-02-18-2011/IMG_0105JPGa-1.jpg
http://i700.photobucket.com/albums/ww1/wpano/Evade-Updated%20Photo-02-18-2011/IMG_0047JPGa-1.jpg

[ccracin]

Bill,

Those wheels really step it up. And I thought that wasn't possible for this car. Very nice! :thumbsup:

[dmc69]

i really like the new wheels... they add a completely diff look to the car.:thumbsup:

[awr68]

Love it Bill! I like the changes!! :thumbsup:

[elitecustombody]

Beautiful machine you got there:thumbsup: Just bring it down a few inches:yes:

BTW, I hope you tightened up the loose bolts on new wheels

[tones2SS]

Very, very nice.:thumbsup:

[fleet]

Very, very nice.:thumbsup:

X2

New wheels changed the look just a little, huh? :D

[bdahlg68]

Looks awesome! Love the stance, exactly what I'm going for.

[68/Camaro]

C F Bumpers on "Evade" by Tom Argue Design

http://i700.photobucket.com/albums/ww1/wpano/Updated%20Evade%20Pictures%2002-19-2011/IMG_0140.jpg

http://i700.photobucket.com/albums/ww1/wpano/Updated%20Evade%20Pictures%2002-19-2011/IMG_0157.jpg

[syborg tt]

Bill - Looks very nice

[68/Camaro]

Bill - Looks very nice

Thanks Marty! Here ya go!
http://i700.photobucket.com/albums/ww1/wpano/2%20Updated%20Evade%20Pictures%2002-19-2011/IMG_0142.jpg

[fleet]

"What are we going to do tonight, Brain? The same thing we do every night Pinky, try and take over the world!"

With these further additions, it looks like Evade will continue its world domination of the 'SuperBadd '68 Camaro' category. :unibrow:

[68/Camaro]

"What are we going to do tonight, Brain? The same thing we do every night Pinky, try and take over the world!"

With these further additions, it looks like Evade will continue its world domination of the 'SuperBadd '68 Camaro' category. :unibrow:

Thanks Skip!
a little tweak here and there you never know what could be next:cool:

[Rybar]

Evade looks Killer Bill. Love the new wheels and bumpers. :thumbsup:

[tones2SS]

Evade looks Killer Bill. Love the new wheels and bumpers. :thumbsup:

What Ryan said here. Looks great Bill.:thumbsup:

[68/Camaro]

I posted this in manual trans section so i thought i would go ahead and post this in my build section of Evade I Was at the NSRA-Southeast Street Rod Nationals this past weekend and driving the "Evade" all three days back and forth from the house 45 minutes each way it was a great weekend and even took home a Award Pick of the Show presented by (ISCA) International Show Car Association. I was about 4 miles from the house went to down shift in fourth gear and would not go? had a serious grind trying to shift the shifter sounded like it was shifting in each gear however its fricking stuck in 5 gear had no other choice but to drive it home in 5th I now i burned the hell out of the clutch! but was able to make it home, on Monday morning called Keisler and left a voice mail for Shafi Keisler and e-mailed him since I bought the complete TKO-600 package from them..... its been three days and NO phone call! or NO e-mail what great service! :thmbsdwn:
need help? also Ive been Contemplating for the past 8mo swapping out the TKO and step up to the T-56.. Now since I will be changing the whole clutch it might be a no brainier any advice?
Thanks,
Bill