68 Camaro build

[Vince@Meanstreets]

That looks great Jay. TMI is killin it!!!!

[n77nxc]

Looking great man!

[Swain]

Few pics.

[Swain]

...........

[Richio1]

Sweet. I like it.

[tubbed69]

That's very nice Jay,so close now:trophy-1302:

[Ricochet]

Interior looks great! I like the charcoal with red stitching! Nice contrast!

[Swain]

Just got my new Baer Re Master.

[Justin@EntropyRad]

The recessed taillights look like shelby tails at first glance. Overall it's sick!

[DOOM]

Jay it's looking awesome!

[Swain]

Got the Car Back from TMI last week. The center console and Dash pad will be here at the end of this week.
The interior came out awesome. Couldn't be happier.

My Daughter loves her new spot lol

[bulldog19]

Looks great Jay. She seems to like it!!

[WSSix]

looks good, Jay! Will the front and rear consoles run together to make one or will they stay separate?

[Swain]

looks good, Jay! Will the front and rear consoles run together to make one or will they stay separate?

The are separate. ill post pics soon as I get it back

[tubbed69]

Jay super nice job on the interior but I would have to pick the pretty little girl,great job:trophy-1302:

[n77nxc]

Looks awesome dude!

[waynieZ]

The interior came out great, and it looks like your little passenger approves !

[Richio1]

Looks great Jay. Flows very nicely. I'm interested to see the dash pad installed. I like the one they had at SEMA.

You going to run their trunk kit too?

[tones2SS]

Looking great Jay!
Very nice.

[Swain]

Looks great Jay. Flows very nicely. I'm interested to see the dash pad installed. I like the one they had at SEMA.

You going to run their trunk kit too?

Same style dash of they had at SEMA. Trunk kit is installed also I'll take some pics tomorrow.

[GregWeld]

Sick dude! Love it!


Wow -- it's like almost a driver! Can you stand the wait?

[Richio1]

Same style dash of they had at SEMA. Trunk kit is installed also I'll take some pics tomorrow.

Thanks Jay

[RBEAST]

Bitchin Ride!!

[Swain]

Few More pics

Getting very close. Should have my Ultimate Headers by the end of the week.

[Black93GT]

Its almost destiny that I see these photos just after I found TMI's products online. I like the look of the seats... well the whole interior is amazing for that matter. I was worried about how the grommets would be on road trips and long drives with less than perfect roads.

Lucky for you they're so close to HB. I'm thinking next time I'm down I'll have to swing by there.

[1transam]

Man i really love what TMI has done with your car. Very nice!

[waynieZ]

That looks sweet! They did a great job.

[Swain]

Mock up of Intake.

Should have it back from Powder coating this week.

[n77nxc]

Very clean...nice work!

[Spiffav8]

Looks great Jay! Man...it's getting sooooo close to being done.

:headspin:

[DKz Garage]

Looks awesome.... can almost see the finish line??

[Swain]

Hopefully fire her up in a few days. I'm going to break a bottle of Champs over the hood lol

[Intimidator3]

Holy Sh*t, Jay. I must have missed the last couple of updates. I can't believe it is almost there! The interior... Wow!!!! And nice fab work on the intake. :trophy-1302:

[Swain]

Intake in stalled, Brakes are Bled. All fluids are in the engine. So close

[Richio1]

Awesome. your getting there. This is such a great time during the build.

When will you be firing it?

[Swain]

Holley Valve covers and coils mounted. Engine turns over. Almost time for a cruise.

[tubbed69]

That's great news Jay,looks great

[awr68]

Very nice build, Jay! So close to driving it! You must be very excited!!!

[MisterD]

Congrats Jay! The engine compartment is looking great! Can't wait to see her run.

[randy]

why don't you flip the fuel rail so its closer to the fuel supply on the passenger side?

[Efi69Cam]

why don't you flip the fuel rail so its closer to the fuel supply on the passenger side?


not to thread-jack but can you still put a fuel pressure gauge on the schrader valve when you flip the rail?

[Swain]

why don't you flip the fuel rail so its closer to the fuel supply on the passenger side?

I have the fuel line hardlined down the driver side of the car. The fuel regulator was going to be too close to the exhaust in the pass side.

[Swain]

Few pics from this weekend.

[dhutton]

Looks great. I like the color in that last pic. Is that a tricoat paint?

Are those Boze wheels? Or are they HRE? :mock:

Don

[n77nxc]

Looks great. I like the color in that last pic. Is that a tricoat paint?

Are those Boze wheels? Or are they HRE? :mock:

Don

Definitely Boze :lol:

Car looks great Jay!

[Swain]

BOZE by Budnik lol jk.

Can't wait to drive this thing

[Swain]

Got the cars wiring all finished, but the wire to th fuel pump wasn't getting juice. Time to find out what the problem is

[andrewb70]

Holley Valve covers and coils mounted. Engine turns over. Almost time for a cruise.

In the picture it looks like you have the older Russell fuel rail fitting with the plastic clip. Get rid of that thing ASAP before it burns your whole car down.

Andrew

[Swain]

In the picture it looks like you have the older Russell fuel rail fitting with the plastic clip. Get rid of that thing ASAP before it burns your whole car down.

Andrew

Do they leak? Tested everything and no fuel leaks

[n77nxc]

Been reported they do leak. Russel switched to the screw in retainer after reports the plastic clips were failing.

[andrewb70]

Do they leak? Tested everything and no fuel leaks

They have been known to burn cars down to the ground. No joke. The new Russell fitting is good and Earl's also makes a nice one with metal clips and an external clip for safety.

Andrew

[randy]

where did you put your O2 sensors? in the header extensions or in the headers themselves?

[Swain]

where did you put your O2 sensors? in the header extensions or in the headers themselves?

They are threaded into the headers

[randy]

They are threaded into the headers

i thought they had to be at a 45 degree angle? the headers place the sensor horizontal.

[Swain]

Never heard of that they are Ultimate Headers.

[andrewb70]

i thought they had to be at a 45 degree angle? the headers place the sensor horizontal.

Sensors can be anywhere from horizontal to straight up, as long as they are in the top half of the header collector. The reason for this is so that condensation does not pool inside the sensor.

Andrew

[Leroy Rochester]

Man, that is a great looking car. Very nice job!

[Swain]

Man, that is a great looking car. Very nice job!

Where in HB do you live?

[Leroy Rochester]

Where in HB do you live?

Main and Adams. Hope to see the car around town sometime soon!

[Swain]

Few pics from last weekend.

Cars pretty much done besides some cosmetic.

Things that need to be done:
Window regulators rear replaced
Shifter boot
Stereo installed
Charge AC

[JDODDS187]

Absolutely beautiful! Very inspiring :idea:

[waynieZ]

Jay the car looks great.

[TomM]

Looks killer....so we can assume you figured out why it wouldn't start....

T,

[Swain]

Looks killer....so we can assume you figured out why it wouldn't start....

T,

Well I guess it just took a few times of me spraying a tiny bit of starter fluid and letting it run. Some reason the injectors didnt spray enough fuel to start it. Runs like a champ now. This car hauls I was surprised this LS3 480 had that kind of power

[Spiffav8]

Jay the car looks absolutely sick! Hopefully there will be video before long.

:thumbsup: :thumbsup:

[Swain]

Jay the car looks absolutely sick! Hopefully there will be video before long.

:thumbsup: :thumbsup:

Just got a GoPro so we should have something soon. :relax:

[WSSix]

Congrats, Jay! Go out and enjoy the ride.

[tubbed69]

Great job Jay,car turned out extremely nice:trophy-1302:

[Che70velle]

Car looks great Jay!

[Swain]

Thanks guys. Tim to put some miles on her

[Spiffav8]

Thanks guys. Tim to put some miles on her

You could drive to Vegas and take your buddy Curtis for a ride. Just sayin...

[Lenie]

Looks great Jay..Congrats.

[Penny]

Looking good!

-Cole

[Swain]

Changed my rear wheel off sets, also changed out the wheels to powder coat instead of Ceramic.

[GregWeld]

Awesome Jason!! You have to be one happy SOB!

[Swain]

Awesome Jason!! You have to be one happy SOB!

Ya now just the final touches.

Super Chevy will be shooting it soon as I have everything in order.

[tubbed69]

Ya now just the final touches.

Super Chevy will be shooting it soon as I have everything in order.

That sounds great Jay,good talking to you a little earlier,thanks for the help with the wheels,your car turned out great.

[Spiffav8]

Ya now just the final touches.

Super Chevy will be shooting it soon as I have everything in order.

Well that doesn't suck! Congrats!!

Car looks sick. :captain:

[califconstruct]

Ohh nice! Looking good!🚥🏁

[Swain]

Pretty pumped on how it all came out. I decided to try to make my tail pipes myself so I will post progress pictures this week. :confused59:

[waynieZ]

The car looks Sweet! Jason.

[Sonar Chief]

The car looks Sweet! Jason.

X2 ... gotta love that color and the stance is perfect :king:

Michael

[randy]

what were your thoughts on the 1 piece headliner? what style did you get? Any cutting or everything slides in place?

[Jerebus67]

How much did the rim and tire package cost you and where did you source?

[Roberts68]

How much did the rim and tire package cost you and where did you source?

You might say he "knows a guy".

In the meantime... Here's a link (http://www.budnik.com/g-series-wheels/g10/) for you.

:flag2:

[Josh@Ridetech]

Pretty pumped on how it all came out. I decided to try to make my tail pipes myself so I will post progress pictures this week. :confused59:

You should be! That car is perfect.

[CHJNCSU]

Amazing Build Congratulations!