update on my 66 pro touring mustang, project wild horse.

[sacarguy]

So far the things I have done.

full frame made out of 2x3 steel
replace floor pans that needed it
replace lower rear quarter and inner panels
seam seal entire under side of car
fabricated firewall and trans tunell.
paint whole underside of car with 3m body sholtz
tub car and install martz four bar rear suspension
install heidts mustang 2 ifs and fabricate inner fenders and upper fender mount rails.

I will be mounting the suspension back on the car and hanging fenders and starting body work now setting all the gaps etc, shaving the drip rails and smoothing the roof
Fabricate the dash mods and center console
fabricate the mounts under the dash for the ac system
fabricate the mounts for the 07 gt-500 motor and 5 speec tk0-600 transmission.

trans tunel already coated
http://i76.photobucket.com/albums/j10/8urls1/1966%20mustang/DSCN0145.jpg
http://i76.photobucket.com/albums/j10/8urls1/1966%20mustang/DSCN0139.jpg
wheel tubs
http://i76.photobucket.com/albums/j10/8urls1/1966%20mustang/DSCN0141.jpg
http://i76.photobucket.com/albums/j10/8urls1/1966%20mustang/DSCN0142.jpg
through floor new fram rails
http://i76.photobucket.com/albums/j10/8urls1/1966%20mustang/DSCN0138.jpg

[sacarguy]

rear suspension
http://i76.photobucket.com/albums/j10/8urls1/1966%20mustang/DSCN0143.jpg
new firewall
http://i76.photobucket.com/albums/j10/8urls1/1966%20mustang/DSCN0159.jpg
front floor pan and trans tunel tacked in
http://i76.photobucket.com/albums/j10/8urls1/1966%20mustang/DSCN0156.jpg
drivers floor pan and new through floor full frame.
http://i76.photobucket.com/albums/j10/8urls1/1966%20mustang/DSCN0146.jpg
http://i76.photobucket.com/albums/j10/8urls1/1966%20mustang/DSCN0147.jpg

[sacarguy]

rear trunkl tubs seam sealed
sealer you see inside fender is there to protect inside of the quarter panel weld I will be body shultzing the whole trunk and inner quarters as well then painting it with splater paint for a strong durable atractive trunk finish.

http://i76.photobucket.com/albums/j10/8urls1/1966%20mustang/DSCN0148.jpg
http://i76.photobucket.com/albums/j10/8urls1/1966%20mustang/DSCN0149.jpg
new lower quarter panels installed
http://i76.photobucket.com/albums/j10/8urls1/1966%20mustang/DSCN0150.jpg
http://i76.photobucket.com/albums/j10/8urls1/1966%20mustang/DSCN0151.jpg

just a pic of the car with the fenders hung and suspension on it.
http://i76.photobucket.com/albums/j10/8urls1/1966%20mustang/DSCF0309.jpg

[Tom.A]

Looks great. Keep us posted :thumbsup:

[sacarguy]

Got the whole car into three coats of green self etching primer

Then painted the whole out side of the car in black epoxy, so now no worries about rust while I seam seal the inside.

Then I will put the lizzard skin down then start on all the custom dash work and the actual body work.
http://i76.photobucket.com/albums/j10/8urls1/1966%20mustang/DSCN0168.jpg
http://i76.photobucket.com/albums/j10/8urls1/1966%20mustang/DSCN0167.jpg
http://i76.photobucket.com/albums/j10/8urls1/1966%20mustang/DSCN0166.jpg
http://i76.photobucket.com/albums/j10/8urls1/1966%20mustang/DSCN0165.jpg
http://i76.photobucket.com/albums/j10/8urls1/1966%20mustang/DSCN0163.jpg

[sacarguy]

more
http://i76.photobucket.com/albums/j10/8urls1/1966%20mustang/DSCN0162.jpg

[GHOSTDANCER]

Good looking project :thumbsup: :cheers:

[dmc69]

lookin good!

[steemin]

Very nice.
What size tire will you be using in the rear?
Will the car have a back seat?

Scott

[sacarguy]

rear will be 335 or 345 front a 265 or 275

[steemin]

rear will be 335 or 345 front a 265 or 275

:hail:
That will be sweet.
I can only dream about meats like that tucked under my 65.
Just curious.
Will the car have a back seat?
I am really enjoying following your projects progress
Keep the updates coming:thumbsup:
Scott

[awr68]

Looking good, nice project!!

[sacarguy]

works going in spurts.

just disasembled all the chrome trim and sand blasted it and had it powder coated satin black in preperation for the reasembly.

will have the bumpers satin black as well.

[D-Speed 2.5]

Any updates? I'm anxious to see how that wheel setup ends up.

[spaghettio]

any new updates?

[Heidts#14]

Very nice project!!! Looks really good. But........I have to make one correction. That is not a Mustang II front. Its even better. Its the Superide II. Sweet........:thumbsup:

[city_ofthe_south]

Great project. I personally love seeing coupes get treated so nicely. Gonna look killer from the sounds of it.

[spaghettio]

any updates? i also have a 66 coupe and wandering how your car is turnion out

[waynieZ]

Nice project it looks great.

[nvr2fst]

just a pic of the car with the fenders hung and suspension on it.
http://i76.photobucket.com/albums/j10/8urls1/1966%20mustang/DSCF0309.jpg[/QUOTE]

What manufacturer wheels are those. They look good on that body style.
Great progress so far.
Dave

[ArisESQ]

I think those wheel are Foose Nitrous.


Are you gonna have a rear seat? Wondering how it'll fit in there!