Mr.VENGEANCE
08-17-2007, 10:08 PM
Looks like im going to do an Art morrison subframe so my suspention parts are forsale.
all parts were only mocked up, i never had the chance to ride on these at all.. sad but true..
so most of these are in "NEW" condition or like new..
of the ones i dont have pictures for ill get them later they are dusty from sitting there.
---- ATS AFX tall spindles for 1st gen Camaro.. used, great condition. SOLD TO MrQuick
---- Global West UCAs with Del-A-Lum buschings.. mocked up only new condition.. $500 shipped.
---- Speedtech LCAs.. mocked up only new condition.. $475 and shipping. SOLD to Steve Firebird
---- Hotchkis 2 inch drop coils with 1 coil cut.. $85 shipped. SOLD to Andrew mcBride
pictures below shown are the ride height with the coils.. pre coilovers.
---- Stock 67-69 front subframe, dirty but in GREAT shape with NO rust. $150 pick up only.
---- Brushed aluminum closeout panel "above the radiator" $70 and shipping.
http://i11.ebayimg.com/04/i/000/a7/46/096c_12.JPG
---- NEW QA1 GMP14 Small Block Coilover Kit complete w/ QA1 spanner wrench and thrust bearing Kit.. fully adjustable. $415 shipped
http://i16.photobucket.com/albums/b19/SlvrSierra/parts014.jpg
---- SBC 406 chevy motor TH350 tranny.
http://www.hostdub.com/albums/DarkDemon/EngineShot.sized.jpg
The engine block was fully reconditioned
Edelbrock Performer RPM aluminum heads (64cc straight plug
chambers)
Edelbrock Performer RPM aluminum intake manifold
Lunati cast crank and pistons assembled for 10:00-1 compression
Lunati "number 10" 292/292, Lift.480/ .480
Holley 750 vacuum advance carburetor
GM HEI distributor
this is probably one of the best sounding and reliable motors out there with GREAT street manners. never had a problem with it..
engine is already pulled and ready to go.
Make and offer.
---- Boyd Coddington HARM 17x8 and 18X10s with Nexen tires.
215/40/17, 265/35/18 4.75" bs front and 5" bs rear
only ridden on them MAYBE 500 miles.. IF that.. they fit PERFECTLY 0n a 1st gen Camaro/Firebird. $1750 and shipping. i waited damn FIVE MONTHS for these wheels!
http://www.hostdub.com/albums/DarkDemon/VenomSide.jpg
i didnt get to drive my car at all during the build.. and im starting over.. so these parts are up for sale.. i do accept paypal with the 3% fee must be included.
Im in ATLANTA if anyone wants to come and pic up.
[email protected]
email me or Im me here.
THANK YOU!
all parts were only mocked up, i never had the chance to ride on these at all.. sad but true..
so most of these are in "NEW" condition or like new..
of the ones i dont have pictures for ill get them later they are dusty from sitting there.
---- ATS AFX tall spindles for 1st gen Camaro.. used, great condition. SOLD TO MrQuick
---- Global West UCAs with Del-A-Lum buschings.. mocked up only new condition.. $500 shipped.
---- Speedtech LCAs.. mocked up only new condition.. $475 and shipping. SOLD to Steve Firebird
---- Hotchkis 2 inch drop coils with 1 coil cut.. $85 shipped. SOLD to Andrew mcBride
pictures below shown are the ride height with the coils.. pre coilovers.
---- Stock 67-69 front subframe, dirty but in GREAT shape with NO rust. $150 pick up only.
---- Brushed aluminum closeout panel "above the radiator" $70 and shipping.
http://i11.ebayimg.com/04/i/000/a7/46/096c_12.JPG
---- NEW QA1 GMP14 Small Block Coilover Kit complete w/ QA1 spanner wrench and thrust bearing Kit.. fully adjustable. $415 shipped
http://i16.photobucket.com/albums/b19/SlvrSierra/parts014.jpg
---- SBC 406 chevy motor TH350 tranny.
http://www.hostdub.com/albums/DarkDemon/EngineShot.sized.jpg
The engine block was fully reconditioned
Edelbrock Performer RPM aluminum heads (64cc straight plug
chambers)
Edelbrock Performer RPM aluminum intake manifold
Lunati cast crank and pistons assembled for 10:00-1 compression
Lunati "number 10" 292/292, Lift.480/ .480
Holley 750 vacuum advance carburetor
GM HEI distributor
this is probably one of the best sounding and reliable motors out there with GREAT street manners. never had a problem with it..
engine is already pulled and ready to go.
Make and offer.
---- Boyd Coddington HARM 17x8 and 18X10s with Nexen tires.
215/40/17, 265/35/18 4.75" bs front and 5" bs rear
only ridden on them MAYBE 500 miles.. IF that.. they fit PERFECTLY 0n a 1st gen Camaro/Firebird. $1750 and shipping. i waited damn FIVE MONTHS for these wheels!
http://www.hostdub.com/albums/DarkDemon/VenomSide.jpg
i didnt get to drive my car at all during the build.. and im starting over.. so these parts are up for sale.. i do accept paypal with the 3% fee must be included.
Im in ATLANTA if anyone wants to come and pic up.
[email protected]
email me or Im me here.
THANK YOU!