Centerforce DFX or Dual Friction please chime in

[NorCal72]

Wondering if the DFX will be to aggressive or have to much chatter. Application is a 600+hp supercharged Gen1 383, LT t56, Detroit 4.11's,
335's in a Gen II Camaro.

Some road race/drag/autoX but it will be driven on the street a lot.

Thanks in advance for any input.
(I've asked for opinions before but I'm getting ready to drop the hammer and want to make sure. Sorry for being repetitive.)

:cheers:

[67ragtp]

Ive used them both, the DFX will chatter your teeth, I wouldn't recommend it on the street very harsh on engagement.

The dual friction is a decent clutch might just be outside your power requirement, if you decide on this one explore the possibility of fitting a 12 inch pressure plate for more clamping force. I believe it will fit.

I love my DYAD, never chatters, has great street manners and enough grip to hold my motor and yours combined.

Mcleod rst/rxt is a good piece as well.

Rich

[NorCal72]

Ive used them both, the DFX will chatter your teeth, I wouldn't recommend it on the street very harsh on engagement.

The dual friction is a decent clutch might just be outside your power requirement, if you decide on this one explore the possibility of fitting a 12 inch pressure plate for more clamping force. I believe it will fit.

I love my DYAD, never chatters, has great street manners and enough grip to hold my motor and yours combined.

Mcleod rst/rxt is a good piece as well.

Rich

That's the issue, with my Gen I SBC/LT1 conversion flywheel I have to run the LT1 clutch setup. Centerforce doesn't make DYAD for my application, McLeod doesn't make a RST/RXT option either. The Centerforce dual friction seems to be the best option. However, I agree with you on the power being a bit too much for that clutch. I've looked at the SPEC Stage 3+ as well but I've read a lot of mixed reviews. So confused LOL :willy:

[67ragtp]

Give the guys at centerforce a call. I Think you will be ok with the Dual friction. I ran it on a 540 cu in, Mitchell BB making near 700 ft lbs. It performed great, it wasn't until I made 5 passes with a set of Hooser QTPs hooking hard at the drag strip that I started smelling friction material. Real nice on the street, you more than likely will blaze your tires which takes a significant load off the drivetrain(clutch). Even the 335 r888s on my camaro with 500+ rear wheel blaze 1st and 2nd gear effortlessly, its just not as much impact on the drivetrain when the tires spinning.
Good luck- Rich

[funcars]

I was on the edge and slipped occasionally running a dual friction with my 90 corvette and a 400 roller cam motor with 315 R tires. With even more torque and sticky tires I would think you stand a good risk.

[NorCal72]

I was on the edge and slipped occasionally running a dual friction with my 90 corvette and a 400 roller cam motor with 315 R tires. With even more torque and sticky tires I would think you stand a good risk.

More conflicting, but great info. Im totally undecided on which way to go. Thanks for the replies.

[214Chevy]

Guys, I'm partial to the RAM dual clutch disks. I ran one with my BBC 509 about 8 years ago. What's you all's opinions on RAM clutches? I always see lots of guys on here mention and run the DYAD, but not many RAM's. Although pricey, I loved them and plan to run one with my 427 supercharged LS7. Do guys not like RAM clutches or what?

[Zspoiler]

I have 79 Z-28 Camaro with 500 plus Supercharged small block Chevy.with a Center Force Dual Friction clutch /Super T-10 / Lakewood Scatter Shield Combo.And I have never had such a problem. Are you running a Scatter Shield.and its not aligned properly It could cause such a problem. I would also ask them for advice as well.

[Twoblackmarks...]

More conflicting, but great info. Im totally undecided on which way to go. Thanks for the replies.

My tips would be that, whatever clutch you choose, if you are gonna use it on the STREET, Select one With springs, or some sort of damping. The springs helps a lot on "smooth" engaging. On what clutch is better or worse, I do not know.

But 600+ Blown HP, plus Good Grip in a second gen (Heavy car?) would probably need a stout clutch.

[NorCal72]

Guys, I'm partial to the RAM dual clutch disks. I ran one with my BBC 509 about 8 years ago. What's you all's opinions on RAM clutches? I always see lots of guys on here mention and run the DYAD, but not many RAM's. Although pricey, I loved them and plan to run one with my 427 supercharged LS7. Do guys not like RAM clutches or what?

I've seen people that swear by them and others that have nothing good to say. I've not seen much negative press about RST/RXT, DYAD, Dual Friction except the Dual Friction cant handle huge HP numbers.

Being that I have use a LT clutch Im still screwed. They don't make a RST/RXT or DYAD for the LT. I think the Dual Friction Centerforce will come up a bit short. Nothing against a RAM I just need to hear some feedback on a 6-700hp (depending on boost) application and what model they are using (I need to be somewhat streetable)

[214Chevy]

.....Nothing against a RAM I just need to hear some feedback on a 6-700hp (depending on boost) application and what model they are using (I need to be somewhat streetable)

Oh no, I wasn't trying to start a cluth convo war or anything. Since, this was a discussion on cluches, I thought I'd get insight as well. I too, am interested in the best streetable clutch cuz I'm supercharging my engine too and need something to handle boost. Wasn't trying to thread jack either.

[NorCal72]

Oh no, I wasn't trying to start a cluth convo war or anything. Since, this was a discussion on cluches, I thought I'd get insight as well. I too, am interested in the best streetable clutch cuz I'm supercharging my engine too and need something to handle boost. Wasn't trying to thread jack either.

I didn't take it that way at all. FYI I've heard the DYAD is very streetable and can handle around 1000hp +- (I think lol). That's what I would be running if they made one for my application.

[214Chevy]

I didn't take it that way at all. FYI I've heard the DYAD is very streetable and can handle around 1000hp +- (I think lol). That's what I would be running if they made one for my application.

Okay, cool. I may have 2 look into those more. Like I said, I had planned on going with RAM, but I'll check out the DYAD. Thanks!