PDA

View Full Version : GMR BILLET Front C5/6 Hubs

MillerBuilt
09-08-2013, 05:35 PM
Up for sale is my personal set of Billet Front C5/6 Hubs. My project has changed course and these are no longer needed.

These are a direct replacement for the stock C5/6 hub units. They retail at over $2020.00+ tax as pictured with Wilwood Rotor Adaptors & Socket Tool (to tighten spindle nut).
This pair can be yours for $1300.00 obo (Mesa,AZ)

***I can accommodate different Caliper/Rotor combinations.
***This setup will add just under +3/16" per side to track width.
MillerBuilt
09-22-2013, 09:11 AM
Sunday Bump!
MillerBuilt
10-27-2013, 04:15 PM
Sunday ttt!
MillerBuilt
11-10-2013, 05:39 PM
To The Top...
raustinss
01-12-2014, 09:55 PM
Still available?
MillerBuilt
01-13-2014, 07:38 PM
Actually have two sets available...
MillerBuilt
01-28-2014, 07:14 PM
Below are with WILWOOD Rotor Adapters....
http://i35.photobucket.com/albums/d179/jaymillerone/C6WilwoodHubs_zps4812bc04.jpg (http://s35.photobucket.com/user/jaymillerone/media/C6WilwoodHubs_zps4812bc04.jpg.html)

Below are with BAER Rotor Adapters....
http://i35.photobucket.com/albums/d179/jaymillerone/C6BAERHubs_zps1ca9c9d2.jpg (http://s35.photobucket.com/user/jaymillerone/media/C6BAERHubs_zps1ca9c9d2.jpg.html)
MillerBuilt
02-23-2014, 07:39 PM
I also have available 2 sets that where used for mock-up ONLY. They are nearly flawless with the exception of a few VERY minor scratches that will not show once mounted. These sets I will sell at a highly discounted rate of $900 per set!!!!! :hairpullout:
raustinss
02-23-2014, 07:42 PM
I think I already know the answer but would they work with stock Z06 rotors
Ryan Austin
MillerBuilt
02-23-2014, 08:00 PM
I think I already know the answer but would they work with stock Z06 rotors
Ryan Austin

Although not designed with this rotor application in mind, YES it will work. You would slide the one piece rotor over/onto the Billet Hub just like the OEM, then you would be required to put spacers between caliper mounting lug and the C5/6 Upright caliper mounting point (basically spacing the caliper out over the rotor that would be sitting "outward" approx. 3/16"...... these spacers can be purchased at most any ACE hardware/etc. in the form of a extra thick washer. I use the same type setup when mounting Brake Man Calipers to these hubs....
MillerBuilt
03-01-2014, 06:20 PM
I also have available 2 sets that where used for mock-up ONLY. They are nearly flawless with the exception of a few VERY minor scratches that will not show once mounted. These sets I will sell at a highly discounted rate of $900 per set!!!!! :hairpullout:

Still available, this is a great deal!
MillerBuilt
03-24-2014, 07:51 PM
Bump!
MillerBuilt
06-08-2014, 06:36 PM
Below are with WILWOOD Rotor Adapters....
http://i35.photobucket.com/albums/d179/jaymillerone/C6WilwoodHubs_zps4812bc04.jpg (http://s35.photobucket.com/user/jaymillerone/media/C6WilwoodHubs_zps4812bc04.jpg.html)

Below are with BAER Rotor Adapters....
http://i35.photobucket.com/albums/d179/jaymillerone/C6BAERHubs_zps1ca9c9d2.jpg (http://s35.photobucket.com/user/jaymillerone/media/C6BAERHubs_zps1ca9c9d2.jpg.html)

I also have available 2 sets that where used for mock-up ONLY. They are nearly flawless with the exception of a few VERY minor scratches that will not show once mounted. These sets I will sell at a highly discounted rate of $900 per set!!!!! :hairpullout:

Bump!