Custom welding carts, let's see them

[scherp69]

I'm doing things a little backwards. I know this is usually the fist project when you get a welder, but I got a cart for free when I bought my welder. I'm looking to build a cart that will hold all my welding accessories and wire. I know there are other forums like the garage journal that have lots of pics, but thought some guys might have some with a pro-touring flare. So like the title says, let's see them.

[SWAPMEETCRAZY]

Converted a napa box....still has all working drawers...cord on rear for grinder...I leave top open as seen...goes anywhere..........jim

[coolwelder62]

Northern Tool sell's 2 cart's almost like this.1 unit is for 1 welder/1 gas bottle.The other is set up for 2 Gas bottle's & 2 welder's.Price is reasonable too.

[Revved]

Don't have any pics but I've seen a few guys take Rubbermaid two or three shelf carts and convert them to welding carts with plenty of storage space. Cut holes and drop your bottles down in for stable mounting. Cut holes and drop PVC down in for clean filler rod storage. Plenty of room for your welder and all your accessories.

[XLexusTech]

I use a mini shopping cart that i found then cut up a bit.. its funny looking but works perfectly and the casters are top notch,,

[Sieg]

I'm liking the Rubbermaid idea. TIG on top Plasma on the bottom. :thumbsup:

http://ecx.images-amazon.com/images/I/412cllNNDhL._SL500_AA300_.jpg

Rubbermaid Commercial Structural Foam Service Cart with Lipped Shelves, 2 Shelves, Black, 300lbs Capacity, 31-1/4" Height, 34" Length X 16" Width
$133 shipped Amazon Prime

[Hotrod1]

Needed something to hold my Miller Dynasty 200. Went a little overboard, but wanted to make sure that it could hold the large cylinder. The tube that holds the welder also pivots so the welder can be swiveled towards your viewing angle without moving the whole cart.

[rwhite692]

This is a little cart I made for my MM211 and Hypertherm plasma on the bottom.

[rwhite692]

Needed something to hold my Miller Dynasty 200. Went a little overboard, but wanted to make sure that it could hold the large cylinder. The tube that holds the welder also pivots so the welder can be swiveled towards your viewing angle without moving the whole cart.

Very nice design!

[E.rodz]

ok this might not be considered a cart however very purpose build for tig welding.
http://i643.photobucket.com/albums/uu160/erodz/shop%20tools/006-1.jpg (http://s643.photobucket.com/user/erodz/media/shop%20tools/006-1.jpg.html)

[Sieg]

New mobile welding table under construction........

http://photos.smugmug.com/photos/i-k5tMLTr/1/XL/i-k5tMLTr-XL.jpg

http://photos.smugmug.com/photos/i-GM5XLdW/0/L/i-GM5XLdW-L.jpg

http://photos.smugmug.com/photos/i-w38sFGp/0/XL/i-w38sFGp-XL.jpg

Why I need a bigger stronger table :D

http://photos.smugmug.com/photos/i-TVGVNkJ/0/XL/i-TVGVNkJ-XL.jpg

http://photos.smugmug.com/photos/i-s9nvkQG/0/XL/i-s9nvkQG-XL.jpg

http://photos.smugmug.com/photos/i-qtHDfGt/0/XL/i-qtHDfGt-XL.jpg

http://photos.smugmug.com/photos/i-S55j65m/0/XL/i-S55j65m-XL.jpg

Wouldn't be complete without a sticky!

http://photos.smugmug.com/photos/i-7wCqNJf/0/L/i-7wCqNJf-L.jpg

[rwhite692]

Nice! Great minds think alike. I have a new table under construction as well. I wanted one with casters on it so I can roll it around the shop and outside. The top is currently at the water jet guy getting some stuff done to it.

[coolwelder62]

The table is turning Awesome.:thumbsup: :thumbsup: