Crisis

[Greg from Aus]

I thought it was about time I put together a build thread.
I bought the car from the US about 4 years ago. Long story short bad buy.'
It looked good in the pictures, but we all know how they can lie.

As it was when I bought it.

39632

The start of the strip down

39633

I own blasting company, so we stripped it and look what we found.

39634

39635

39636

[Greg from Aus]

We replaced both quarters, full floor,trunk floor, firewall,roof and both outer wheel wells. I sold of most of the car as I decided to go with a Pro touring setup.

39637

39638

39639

39640

I purchased Art Morrision front and rear clips.

39643

39641

39642

[Greg from Aus]

It's been moving along pretty well the last year.

Bringing it home after the firewall, interior and underside where painted.

39644

The red is Sting Red, the interior is Matt Black and the underside is Gregorio Silverstone.

39645

39646

[Greg from Aus]

brake lines made.

39647

39648

I have set a mock up engine in place, I am running a tall deck RHS block, but I don't have it here yet, so I needed to simulate it by raising the heads of the one I have.

39649

39650

[Greg from Aus]

I have set up the breathers for the diff and fuel tank.

39656

I have been working on the headers and exhaust the last couple of weeks. I have used a header design set by icengineworks, that works great.

39652

39653

39654

39655

[Greg from Aus]

one of the headers all fabbed up.

39657

And the exhaust well underway.

39658

39659

39660

[Greg from Aus]

Radiator, coolers, support panel and dry sump tank in place.

39661

39662

[tubbed69]

you have been holding out on us way too long,that is some great looking work,gonna be a real nice ride

[Greg from Aus]

you have been holding out on us way too long,that is some great looking work,gonna be a real nice ride

Only for a little while Jeff. I will keep it upto date from now on.

[Thomo5150]

Nice work, excellent choice of parts going into this build....

Thomo

[Rick D]

Um Greg :smiley_smack: that's not nice to hold out on us like that :D Very nice build there Greg!! What are the plans for the engine? Love the fire wall.

[Greg from Aus]

Nice work, excellent choice of parts going into this build....

Thomo

Thanks Thomo

[Greg from Aus]

Um Greg :smiley_smack: that's not nice to hold out on us like that :D Very nice build there Greg!! What are the plans for the engine? Love the fire wall.

OK Rick, I promise not to keep things :secret:

The engine is a 440 RHS tall deck block, Ozmo manifold, dry sump and all top self internals.

[Sieg]

What a corker!

Ya dunny rat, about time you shared this fat cracker with us! :bitchslap:

[Greg from Aus]

What a corker!

Ya dunny rat, about time you shared this fat cracker with us! :bitchslap:

:thankyou: Sieg, I hope to get it back to the paint shop, while we are in the States in July and hopefully finished by the end of the year.

[andrewb70]

....

39642

Great progress.

I was just wondering if you were going to run that suspension as a 5 link? I know AM offer both the 3 and 4 link option, but is there a reason to run 5?

Just curious.

Andrew

[Greg from Aus]

Great progress.

I was just wondering if you were going to run that suspension as a 5 link? I know AM offer both the 3 and 4 link option, but is there a reason to run 5?

Just curious.

Andrew

Andrew, it"s the same setup that was being used in Project Unfair, I believe there is only the 2 of them. I will use the 4 link for the drags and the 3 link for everything else.

[Spiffav8]

Dang Greg....way to grab everyone's attention! :D

Crazy nice and I can't wait to see more!!

[GregWeld]

Oh yeah! That'll work!


Thanks for FINALLY posting.... You and I must share that little hold out gene.... I'm big on posting but not big on posting what I'm doing. LOL


You know -- I have to say -- that so many of these cars end up with a complete re-do after being bought when they "looked" okay.... but what we have to remember is that for many many years these cars weren't worth towing to the junkyard... and then there were a few years of "recovery" where they were still just cheap cars... so the repairs were commensurate with their values. It's only now that we can put the proper repairs to them because they're worth the cost and effort. Glad you saved another one.

[Ron in SoCal]

WHen I saw the title of the thread I thought there was an emergency!
You should rename the car 'holdout', lol.

Congrats Greg. Beautiful car :cheers:

[Sieg]

:thankyou: Sieg, I hope to get it back to the paint shop, while we are in the States in July and hopefully finished by the end of the year.

Over the top impressive mate.

Regarding the core support - was it purchased or custom fabricated?

...........I have nightmares about getting my car blasted. :D

[214Chevy]

Very nicely done. :thumbsup:

[John510]

Awesome! :king:

[cencalc6]

Excellent Work!

[Greg from Aus]

Dang Greg....way to grab everyone's attention! :D

Crazy nice and I can't wait to see more!!

Thanks Curtis, I will keep the post coming as they happen.

[Greg from Aus]

Looks killer!!! Can't wait to see more! Keep the pictures coming.

Thanks Jay :thumbsup:

[Greg from Aus]

Oh yeah! That'll work!


Thanks for FINALLY posting.... You and I must share that little hold out gene.... I'm big on posting but not big on posting what I'm doing. LOL


You know -- I have to say -- that so many of these cars end up with a complete re-do after being bought when they "looked" okay.... but what we have to remember is that for many many years these cars weren't worth towing to the junkyard... and then there were a few years of "recovery" where they were still just cheap cars... so the repairs were commensurate with their values. It's only now that we can put the proper repairs to them because they're worth the cost and effort. Glad you saved another one.

Thanks Greg, I have to say it's much easier to watch and listen.

[Greg from Aus]

WHen I saw the title of the thread I thought there was an emergency!
You should rename the car 'holdout', lol.

Congrats Greg. Beautiful car :cheers:

There is an emergency: get it done before I'm to old.

Holdout, now your just being harsh :twak:

[Greg from Aus]

Over the top impressive mate.

Regarding the core support - was it purchased or custom fabricated?

...........I have nightmares about getting my car blasted. :D

It's a PRC unit Sieg.

All we do is blast cars and ruin peoples dreams.

[Greg from Aus]

Very nicely done. :thumbsup:

:thankyou:

[Greg from Aus]

Awesome! :king:

Thanks John, it's great to see progress isn't it, yours is coming along great.

[Greg from Aus]

Excellent Work!

:thumbsup:

[Flash68]

Wow - simply bad to the bone! Wish it was in the States.. :flag2: :D

:thumbsup:

[Sieg]

Wow - simply bad to the bone! Wish it was in the States.. :flag2: :D

:thumbsup:

ROAD TRIP!!!

:unibrow:

[Greg from Aus]

Wow - simply bad to the bone! Wish it was in the States.. :flag2: :D

:thumbsup:

Cheers Flash

[Greg from Aus]

ROAD TRIP!!!

:unibrow:

You are a bad man Sieg. :hitaxeonthehead:

You just never know, It would be bloody expensive, but a great trip.

[Vince@Meanstreets]

nice work greg, what media did you use for the undercarrige? Unusual to see the spot weld color after blasting.

[cjfirstgen]

Very nice! Look forward to seeing the progress.

[Greg from Aus]

nice work greg, what media did you use for the undercarrige? Unusual to see the spot weld color after blasting.

Thanks Vince, We used Soda back then, but we don't use it any more, the car was completely re blasted at a later date, using a system that I developed, called the Diamond blast system.

[Greg from Aus]

Very nice! Look forward to seeing the progress.

Thanks.

[Greg from Aus]

A few more pictures.

I glass bead blasted the Wilwood pedal Assembly and the front suspension pieces and clear coated them, so that they will stand out against the black carpet, that I will use.

39680

39681

Painted and assembled the dash.

39682

[Greg from Aus]

Carbon fiber tail shaft turned up today.

39771

[Ron in SoCal]

This thread is like X-mas :lol:

Gets better with every post Greg :thumbsup:

[Sieg]

Just another Lat-g build on a tight budget. :lmao:

[FETorino]

It's a PRC unit Sieg.

All we do is blast cars and ruin peoples dreams.

That's the truth. Hey what happened to my pristine car. :bang:

You have one hell of a nice project going together :D

Did the carbon shaft come from a local supplier or someone in the states?

[frankv11]

we like pictures here ,, ahhhh thanks for the fix
very nice build. your were lucky, considering some of the cars we have seen come out of sandblasting. or did we missed some of the horrific pictures

[Greg from Aus]

This thread is like X-mas :lol:

Gets better with every post Greg :thumbsup:

Thanks Ron,

How do I multi post?

[Greg from Aus]

Just another Lat-g build on a tight budget. :lmao:

It's being built by super cheap auto's :headspin:

[Greg from Aus]

That's the truth. Hey what happened to my pristine car. :bang:

You have one hell of a nice project going together :D

Did the carbon shaft come from a local supplier or someone in the states?

Yeah I have a lot of clients that wonder the same thing, I had a 70 Mustang that looked pretty good, but after blasting the only panel not replaced was the roof.

Thanks I'm pretty happy with the way it's shaping up.

The tail shaft I bought through a local guy, but it was made in the States.

[Greg from Aus]

we like pictures here ,, ahhhh thanks for the fix
very nice build. your were lucky, considering some of the cars we have seen come out of sandblasting. or did we missed some of the horrific pictures

There are lot's of pictures that you have missed, It was really bad.

[Rick D]

Nice parts Greg!

When I had the resto shop we would always tell the customer before we had the car stripped that it might not come back as a whole car!! It's amazing what people did to some of these cars to make them look ok!

[Greg from Aus]

Nice parts Greg!

When I had the resto shop we would always tell the customer before we had the car stripped that it might not come back as a whole car!! It's amazing what people did to some of these cars to make them look ok!

Yeah Rick, we pull out all the normal, chicken wire, paper machete and expanding foam.

[214Chevy]

...I will keep it upto date from now on.

You better.....:twak: Very well execution on the car build. I like it.

[Greg from Aus]

You better.....:twak: Very well execution on the car build. I like it.

Stop hitting me with that stick, now I have a head ache.

[214Chevy]

Stop hitting me with that stick, now I have a head ache.

Hahahahaha!! Greg, tell us more about the engine. What are you building with the tall deck RHS? It's gonna be a monster, I know

[Greg from Aus]

Hahahahaha!! Greg, tell us more about the engine. What are you building with the tall deck RHS? It's gonna be a monster, I know

No monster, just a little 440.

[WSSix]

Love what you're doing with the car. Hope everything comes together smoothly for you.

[DETON8R]

Man I love the looks of the AME rear suspension!!!
SICK!!

And that exhaust, and the custom headers. What a awesome set up!!
SICK, SICK, SICK!!!

A carbon fiber drive shaft???
Clearly you have a DISEASE because that car is SOOOOO SICK!!

[tmadden]

Just another Lat-g build on a tight budget. :lmao:

no doubt!!

[Greg from Aus]

Love what you're doing with the car. Hope everything comes together smoothly for you.

Cheers Trey

[Greg from Aus]

Man I love the looks of the AME rear suspension!!!
SICK!!

And that exhaust, and the custom headers. What a awesome set up!!
SICK, SICK, SICK!!!

A carbon fiber drive shaft???
Clearly you have a DISEASE because that car is SOOOOO SICK!!

Wow what can I say, :thankyou:

I'm of to hospital, for some treatment. :lmao:

[Greg from Aus]

no doubt!!

:sarcasm_smiley: excepted at any time.

[waynieZ]

Oh yeah! That'll work!
Thanks for FINALLY posting.... You and I must share that little hold out gene.... I'm big on posting but not big on posting what I'm doing. LOL



It Must Be in the name!

Greg it looks awesome ! I'm not mad you held out, I'm pissed I didn't see it until today!!! That's going to be a wild set up what are you expecting for HP? I like the color you used on the bottom it will be nice with the red. Are those bullit mufflers infront of the regular mufflers? Glad to see it coming together!
I'll be watching...

[Greg from Aus]

It Must Be in the name!

Greg it looks awesome ! I'm not mad you held out, I'm pissed I didn't see it until today!!! That's going to be a wild set up what are you expecting for HP? I like the color you used on the bottom it will be nice with the red. Are those bullit mufflers in front of the regular mufflers? Glad to see it coming together!
I'll be watching...

Hey Wayne, I hope you are getting better.

The things in front of the mufflers are Cat's and expansion bellows.

We expect around 700 - 720 hp at the flywheel.

[waynieZ]

Sweet!!!

[Greg from Aus]

Made the other header, got it welded out today only the flanges left to weld.:excited: :excited: :excited: :excited: :excited: :excited:

39792

39793

39794

39795

39796

39797

39798

[Streetking]

Very impressive build!

[Sieg]

Nice job on the headers! :cheers:

[Greg from Aus]

Very impressive build!

:thankyou: SW

[Greg from Aus]

Nice job on the headers! :cheers:

Cheers Sieg, they are a real challenge when you really don't have a clue.

[Sieg]

Cheers Sieg, they are a real challenge when you really don't have a clue.
Challenges are a good test. Best of all........when someone asks where you got those headers you can say I BUILT THEM! Get creative and make your own custom name/logo plate and tack it on a tube. :thumbsup:

That plastic Lego set made it a lot easier didn't it?!

I remember going to their site and checking those out.........(choking on the price mind you)........then when I was fabbing my tailpipes I kept thinking man those would sure make this A LOT simpler. :D

[waynieZ]

Headers are looking good. Nice job.

[tubbed69]

Greg those headers look great ,doing a great job on entire car.

[Greg from Aus]

Challenges are a good test. Best of all........when someone asks where you got those headers you can say I BUILT THEM! Get creative and make your own custom name/logo plate and tack it on a tube. :thumbsup:

That plastic Lego set made it a lot easier didn't it?!

I remember going to their site and checking those out.........(choking on the price mind you)........then when I was fabbing my tailpipes I kept thinking man those would sure make this A LOT simpler. :D


It's character building, I really enjoy the fabrication part of it, theres nothing wrong with learning new skills.

Yeah a lot easier than without I am sure.

They ain't cheap but I have another set to build so it's not too bad, and I can always move them on when I'm finished with them.

[Greg from Aus]

Headers are looking good. Nice job.

:thankyou:

[Greg from Aus]

Greg those headers look great ,doing a great job on entire car.

:thumbsup:

[Greg from Aus]

The final fit up pictures.

I finished the exhaust.

40139

40140

40141

I had a billet resivoir set made

40142

trial fitted the dash and wheel

40143

40144

Now to blow it all apart ready for paint :excited: :excited: :excited:

[tubbed69]

very nice work so far Greg,good luck with paint

[tmadden]

What push button start did you go with?

[Rick D]

Nice work there Greg!! :king:

[Sieg]

Nice work mate :thumbsup:

[DOOM]

Greg lets get some paint on this bad boy already!!!! Lookin awesome!!! Just read in Ron's thread your going to be in Columbus will have to meet up!

[Greg from Aus]

very nice work so far Greg,good luck with paint

Thanks, hopefully it will all go well.

What push button start did you go with?

Advanced keys

Nice work there Greg!! :king:

Thanks Rick

Nice work mate :thumbsup:

Cheers Sieg

Greg lets get some paint on this bad boy already!!!! Lookin awesome!!! Just read in Ron's thread your going to be in Columbus will have to meet up!

Mario, it will be getting painted while I'm in the States. Would love to catch up.

[Vortech404]

Greg,
Car looks awesome. Great job

Are those the 4 1/2" Speedhut gauges? I'm hoping they have another 4th of July sale. What do you think of them?

John

[glassman]

wow, nice set-up! can't believe i missed this one, glad you posted today!

[Ron in SoCal]

The final fit up pictures.

I finished the exhaust.

I had a billet resivoir set made

trial fitted the dash and wheel

Now to blow it all apart ready for paint :excited: :excited: :excited:

Great wrok Greg! I looked at those exhaust hangers, was a bit worried about how high or low they tuck, but you nailed it. :cheers:

[waynieZ]

Greg its looking great, exhaust tucked up nice and tight. Nice set up on the dash . As much as you'll enjoy Columbus you must be dyeing to see it in paint. Enjoy your trip.

[Greg from Aus]

Greg,
Car looks awesome. Great job


Are those the 4 1/2" Speedhut gauges? I'm hoping they have another 4th of July sale. What do you think of them?

John

Thanks John, Yes they are Speedhut, I really like the way they look, I hope they work OK.

wow, nice set-up! can't believe i missed this one, glad you posted today!

Thanks

Great wrok Greg! I looked at those exhaust hangers, was a bit worried about how high or low they tuck, but you nailed it. :cheers:

You have very similar taste Ron, I'm very happy with the outcome.

Greg its looking great, exhaust tucked up nice and tight. Nice set up on the dash . As much as you'll enjoy Columbus you must be dyeing to see it in paint. Enjoy your trip.

Yes I'm getting excited Wayne.

[Greg from Aus]

Here is a teaser, I had to get to the airport, and they were still laying clear.

I will head there in the morning for more pictures. :bigun2: :G-Dub:


41530

[GregWeld]

That'll buff out.......





:gitrdun:

[Ron in SoCal]

Here is a teaser, I had to get to the airport, and they were still laying clear.

I will head there in the morning for more pictures. :bigun2: :G-Dub:


41530

Looks great. Post MOAR pics...:D

[Flash68]

That there's puuuurrrrty.

[214Chevy]

Wow!! Nice paint job.:flashie:

[Rick D]

Very nice Greg, what color is that solid red or a pearl? Can't wait to more!!!:bump:

[waynieZ]

It looks great Greg. I can't wait to see you next update.

[Greg from Aus]

That'll buff out.......

:gitrdun:

I hope so.

Looks great. Post MOAR pics...:D

Thanks Ron, more pic's today.:excited: :excited: :excited:

That there's puuuurrrrty.

:cheers:

Wow!! Nice paint job.:flashie:

:thankyou:

Very nice Greg, what color is that solid red or a pearl? Can't wait to more!!!:bump:

It's a solid red and a metalic rear panel paint out.

It looks great Greg. I can't wait to see you next update.

Thanks Wayne, I'm heading there now, so I will have some more pictures today.

[waynieZ]

Sweet!

[Greg from Aus]

OK here are some from this morning, the cars a bit dusty, as they have started to slice it back.


41535

41536

41537

41538

41539

41540

[Sieg]

I LIKE IT!

Great color and nice contrast on the rear panel. :thumbsup:

[Greg from Aus]

I LIKE IT!

Great color and nice contrast on the rear panel. :thumbsup:

Thanks Mate. I am really happy with the contrast, I think it works well. I have changed from the Z28 stripes to a hockey stripe in the same color for something different than the rendering.

[Sieg]

Thanks Mate. I am really happy with the contrast, I think it works well. I have changed from the Z28 stripes to a hockey stripe in the same color for something different than the rendering.

I like the hockey stripe decision, you don't see a lot of them and in your color combo's it should work very well.

How far are you from driving this beauty?

[Greg from Aus]

I like the hockey stripe decision, you don't see a lot of them and in your color combo's it should work very well.

How far are you from driving this beauty?

Hopefully by Christmas.:headspin:

[tmadden]

Exciting times. The red will be incredible. I like the hockey stripe also. Keep the pics coming

[Greg from Aus]

Exciting times. The red will be incredible. I like the hockey stripe also. Keep the pics coming

Thanks, will do.

[Sieg]

Hopefully by Christmas.:headspin:
Good deal mate! It's the appropriate color to spread holiday cheer. :thumbsup:

[DOOM]

Greg the hockey stripes will look awesome! Great choice..

[Greg from Aus]

Good deal mate! It's the appropriate color to spread holiday cheer. :thumbsup:

:thankyou:

[Greg from Aus]

:thankyou:

Greg the hockey stripes will look awesome! Great choice..

Thanks Mario, how is yours coming along?

[tubbed69]

very nice Greg,hard to beat red,paint looks great:thumbsup:

[streetbird]

very nice.
I love the dash, look like a nascar

[Greg from Aus]

very nice Greg,hard to beat red,paint looks great:thumbsup:


Thanks Jeff.


very nice.
I love the dash, look like a nascar

Cheers mate.

[WSSix]

Looks excellent, Greg. The hockey stripes will look great as well. Good luck getting it finished by Christmas.

[Greg from Aus]

Looks excellent, Greg. The hockey stripes will look great as well. Good luck getting it finished by Christmas.

Thanks Trey, just trying to make it a little different if thats possible :rolleyes:

[waynieZ]

It looks awesome! This car will definitely attract crowds with that shine. I like the idea of the same color stripes as the rear panel. They'll look great together.

[Greg from Aus]

It looks awesome! This car will definitely attract crowds with that shine. I like the idea of the same color stripes as the rear panel. They'll look great together.

Cheers Wayne, the underbody, diff and subframe are all in the same color but low gloss, we tinted the raptor liner for the underbody.

[Rybar]

Wow Greg, not sure how in the heck I missed this thread but your car looks awesome! Love the paint choice! And the motor plans for sure. I'd like to know how low you can get the car to sit with the Morrison rear clip. Anything you can tell us about that? Or pictures of the car on the ground?

Ryan

[DOOM]

Thanks Mario, how is yours coming along?

Greg I'm seeing light at the end of the tunnel! Troy has committed to so dates in the very near future . So I finally have an idea of when it will be done! So its GOOOO time!

[Greg from Aus]

Wow Greg, not sure how in the heck I missed this thread but your car looks awesome! Love the paint choice! And the motor plans for sure. I'd like to know how low you can get the car to sit with the Morrison rear clip. Anything you can tell us about that? Or pictures of the car on the ground?

Ryan

Ryan, I will start assembly in the next couple of weeks, and I will try to find out for you. I will be running the car with clearance most of the time, so it won't be sitting real low.


Greg I'm seeing light at the end of the tunnel! Troy has committed to so dates in the very near future . So I finally have an idea of when it will be done! So its GOOOO time!

Great to hear Mario, plenty of pictures please.

[Greg from Aus]

Well I have big smile, the shell is home. :) :) :D :D

Re painted the underneath, front clip and diff in a less gloss finish.

41647

41648

41649

41650

41651

41652

41653

41654

41655

41656

[Sieg]

Looking good mate! :thumbsup:

I really like your roll bar design, is it a local custom fabrication?

[Greg from Aus]

Looking good mate! :thumbsup:

I really like your roll bar design, is it a local custom fabrication?

Thanks Sieg.

The cage is by a guy over hear called Black Magic race cars, he builds Pro Mods ( called door slammers over here)

[Ron in SoCal]

Looks fantastic Greg! :thumbsup:

Now get busy :D

[carbuff]

I'll echo the looking good comments! :thumbsup:

[tubbed69]

Great job Greg,paint looks slick

[waynieZ]

Great news Greg ! The paint look gorgeous. Nothing like having it close to home.

[Greg from Aus]

Looks fantastic Greg! :thumbsup:

Now get busy :D

Thanks Ron,

I worked on last night and this morning and its a roller again.

I'll echo the looking good comments! :thumbsup:

Thanks Bryan :thumbsup:

Great job Greg,paint looks slick

Cheers Jeff. :happy23:

Great news Greg ! The paint look gorgeous. Nothing like having it close to home.

Yeah your right Wayne, even if it's just to go look at it and dream. :thumbsup:

[tmadden]

Looking very, very, very good!!!!!

[Flash68]

Wow that looks hot out in the sun!

:rockin:

[Greg from Aus]

Looking very, very, very good!!!!!


:thankyou:


Wow that looks hot out in the sun!



:rockin:

Thanks Dave.

[Greg from Aus]

It's rolling,

41686

41687

41688

41689

41690

[Sieg]

Very NICE!!!!!!!

[72Z/28]

Awesome work!!!!

[Greg from Aus]

Very NICE!!!!!!!

:happy23:

Awesome work!!!!

:thankyou:

[Rick D]

Wow goes together fast when you have already done this what 20 times :thumbsup:

Really looking nice!!

:king:

[Greg from Aus]

Wow go together fast when you have already done this what 20 times :thumbsup:

Really looking nice!!

:king:

I reckon at least 20 times Rick :D

[waynieZ]

Looks nice ! Moving right along.

[tubbed69]

that sure is looking great,sure it feels good to have it as a roller again:thumbsup:

[Greg from Aus]

Looks nice ! Moving right along.

that sure is looking great,sure it feels good to have it as a roller again:thumbsup:

Thanks guys

[Greg from Aus]

Todays effort,

Shocks, sway bar, fuel line, brake line tank in and went out for lunch. :excited:

41714

41715

41716

41717

41718

[DOOM]

Greg, it really looks awesome !

[GregWeld]

It just keeps getting better and better!!!!



EEEEEEEEEHHHHHHHHHHHHHAAAAAAAAAAAAA

[Greg from Aus]

Greg, it really looks awesome !

Thanks Mario

It just keeps getting better and better!!!!



EEEEEEEEEHHHHHHHHHHHHHAAAAAAAAAAAAA

Cheers Greg, it's getting there.

[waynieZ]

Nice progress Greg.

[Greg from Aus]

Nice progress Greg.

:thankyou:

[Greg from Aus]

I had a call from a mate today to say my car is in streetlegaltv.com, I had know idea about it, but I'm pretty happy.

http://www.streetlegaltv.com/news/gorgeous-camaro-pro-touring-build-from-australia-project-crisis/

[Sieg]

Congrats mate! Crisis is the dogs balls now! :D

[Payton King]

Another one getting close!

[Ron in SoCal]

Very cool Greg! :thumbsup:

[Greg from Aus]

Congrats mate! Crisis is the dogs balls now! :D

Another one getting close!

Very cool Greg! :thumbsup:

Thanks Guys, I have got to be happy with that.

[glassman]

i specially love the comments from your daughters at the bottom. My girl is the only one of our three children that really shows any interest...

btw, looking great, bet you cant wait to get behind the wheel...

[Greg from Aus]

i specially love the comments from your daughters at the bottom. My girl is the only one of our three children that really shows any interest...

btw, looking great, bet you cant wait to get behind the wheel...

Both my kids are fighting over who will have it when I die :rofl:

Yep I can't wait to drive it but it will be a while.

[Greg from Aus]

Time for a bit of an update.

I have most of the wiring done that I can at this stage. I put the fuse box in the boot and didn't try to hide it, I think it works with the theme of the build, I use an American Auto Wire Hwy 22 kit with extended wires.
I has been a lot of work as I have integrated key less entry and push button start.

42541

I made up a battery kill switch housing.
42542

I had the trimmer install the hood lining and sail panels, I had them made out of perforated vinyl
42543

I made a bracket to hold the fly by wire accelerator pedal.
42544

I made the seat brackets work, and fitted a seat, it all works well. The seats are being recovered to get rid of the writing.
42545

[Greg from Aus]

Time for a bit of an update.

I have most of the wiring done that I can at this stage. I put the fuse box in the boot and didn't try to hide it, I think it works with the theme of the build, I use an American Auto Wire Hwy 22 kit with extended wires.
I has been a lot of work as I have integrated key less entry and push button start.

42547

I made up a battery kill switch housing.
42548

I had the trimmer install the hood lining and sail panels, I had them made out of perforated vinyl.
42549

I made a bracket to hold the fly by wire accelerator pedal.
42550

I made the seat brackets work, and fitted a seat, it all works well. The seats are being recovered to get rid of the writing.
42551

42552

Next was install the fire system and start the plumbing, I need to get some more pipe to finish it.
42553

[Greg from Aus]

I pushed it out side in the sun for a couple of pictures.

42554

42555

42556

42557

42558

[Sieg]

She's a work of art mate! :thumbsup:

[DOOM]

Nice Greg! Its lookin aewsome ! Now get that plane ticket to SEMA!

[Rick D]

Looks great Greg, not long now before you can fire it up!!

[WSSix]

Gorgeous!

[Ron in SoCal]

Love your attention to detail Greg :thumbsup:

[tubbed69]

very impressive work Greg,how close to startup?:gitrdun:

[Vince@Meanstreets]

great work greg, i see alot of european race car influence. beautiful

[carbuff]

Very nice! And I approve of your gauge choice. :)

[Lenie]

Greg, car looks great. I really like the way you've set up your trunk.

[Greg from Aus]

She's a work of art mate! :thumbsup:

Thanks Sieg.

Did you watch Bathurst ? ( V8 Supercars )

Nice Greg looking awesome ! Now get that plane ticket to SEMA!

Cheers Mario,

Not this year, maybe next year although probably be another mid year trip.

Looks great Greg, not long now before you can fire it up!!

Thanks Rick.

Thats just a dumby up engine, I am still waiting for the real one to arrive.

Gorgeous!

:thumbsup:

Love your attention to detail Greg :thumbsup:

Says the man who has it all under control. Cheers Ron :thumbsup:

very impressive work Greg,how close to startup?:gitrdun:

I am hoping the engine will be here in about a month, I have a big car show in mid January that I would like to make. Yours is looking a treat Jeff.

great work greg, i see alot of european race car influence. beautiful

Thanks Vince, as hard as it is, I'm just trying to make mine.

Very nice! And I approve of your gauge choice. :)

Thanks Bryan, they are a nice gauge.

Greg, car looks great. I really like the way you've set up your trunk.

Thanks Lenie,

I'm just floundering my way through, trying to stick to the theme.

[Sieg]

Thanks Sieg.

Did you watch Bathurst ? ( V8 Supercars )

No TV coverage that I've found......hopefully someone will have a replay as I love that track!

Decent race?

[Greg from Aus]

No TV coverage that I've found......hopefully someone will have a replay as I love that track!

Decent race?

They said it was being televised to the States.

GREAT race, the last 50 laps were so tight.

On a side note Sieg, I raced karts with Tander regularly, and Wincup and Winterbottom at Nationals, they were just young fellars coming through and I was already old.

[Flash68]

Frickin stellar! When are you bringin it to the States, California specifically? :)

[Greg from Aus]

Frickin stellar! When are you bringin it to the States, California specifically? :)

That would be nice, but it won't hold a candle to yours.:thumbsup:

[Sieg]

They said it was being televised to the States.

GREAT race, the last 50 laps were so tight.

On a side note Sieg, I raced karts with Tander regularly, and Wincup and Winterbottom at Nationals, they were just young fellars coming through and I was already old.
Motorsports programming is a mess in the US right now. Hopefully I can find at least highlights!

This is interesting: http://jalopnik.com/texas-being-dropped-from-the-australian-v8-supercars-sc-1362802764

Obviously your old age and treachery taught those boys how to race. :D

[Greg from Aus]

Motorsports programming is a mess in the US right now. Hopefully I can find at least highlights!

This is interesting: http://jalopnik.com/texas-being-dropped-from-the-australian-v8-supercars-sc-1362802764

Obviously your old age and treachery taught those boys how to race. :D

Thats a bit of a bummer, I had thought about coming over for that.

[Sieg]

Now I really want to watch it! http://www.v8supercars.com.au/news/build-a-bridge?utm_medium=twitter&utm_source=V8SC

[Greg from Aus]

Now I really want to watch it! http://www.v8supercars.com.au/news/build-a-bridge?utm_medium=twitter&utm_source=V8SC

Like I said, it was great. Rob would love it, a bloody Ford won. :guns:

[Greg from Aus]

Todays update, made a new pedal face for the fly by wire pedal.

I used a punch and dye to create the raised holes in the stainless to look like the Willwood pedals.

42678

42679

42680

42681

42682

42683

42684

[tubbed69]

nice job on the pedals Greg,I have the stock pedal and they are not too pretty are they?

[Greg from Aus]

I also made one for the park brake pedal.

42685

[Greg from Aus]

nice job on the pedals Greg,I have the stock pedal and they are not too pretty are they?

:thankyou:

[GregWeld]

The Fabricator with Thunder from Down Under!


Nicely done! They look great!

[Flash68]

Greg, great touch on the pedals. Looks like it was manufactured as a set.

[waynieZ]

nice job Greg they came out great.

[FETorino]

Like I said, it was great. Rob would love it, a bloody Ford won. :guns:

What:headscratch: Greg I don't even know what you are talking about.

"All this took place just seconds behind an equally intense fight for the lead that eventually went to the Mark Winterbottom/Steve Richards FPR Pepsi Max Falcon ahead of the Red Bull Commodore of Jamie Whincup and Paul Dumbrell." :underchair:

Greg that pedal fab look awesome.:thumbsup: Nobody will ever guess it didn't come as part of the set.

Sometimes that is a shame. You see a finished car and don't even realize the time that went into details such as that.

Thanks for sharing it. Too bad it's on a Camaro:lol: :underchair:

:cheers:

[Greg from Aus]

The Fabricator with Thunder from Down Under!


Nicely done! They look great!

What are you saying, I fart a lot :warning:
Thanks Greg.:thumbsup:


Greg, great touch on the pedals. Looks like it was manufactured as a set.

Thanks Flash.

nice job Greg they came out great.

Thanks Wayne

What:headscratch: Greg I don't even know what you are talking about.

"All this took place just seconds behind an equally intense fight for the lead that eventually went to the Mark Winterbottom/Steve Richards FPR Pepsi Max Falcon ahead of the Red Bull Commodore of Jamie Whincup and Paul Dumbrell." :underchair:

It really was a great race Rob, if you get a chance to watch it, do.

Greg that pedal fab look awesome.:thumbsup: Nobody will ever guess it didn't come as part of the set.

Sometimes that is a shame. You see a finished car and don't even realize the time that went into details such as that.

Thanks for sharing it. Too bad it's on a Camaro:lol: :underchair:

:cheers:

Thats the idea, there the best bit, I think.

[Sieg]

What are you saying, I fart a lot :warning:
The wifey must have tipped him off mate. :sieg:

[Greg from Aus]

The wifey must have tipped him off mate. :sieg:

Yeah she probably did.

[bonecrrusher]

No V8 Supercar in Texas... WTF...

[GregWeld]

No V8 Supercar in Texas... WTF...




It was a very poorly attended event… so it doesn't surprise me a bit that it's not running again. You can only imagine the cost of the transportation - the crews - the air fares etc to ship this stuff all around -- so they have to sell some tickets -- or get some major air time. I don't thing they did either.

[Greg from Aus]

I have been working on the dash pad, what a piece of $hitt. If there is one part I hate in a 69 Camaro it's the dash pad.

I have had all sorts of problems with the fit up to the DSE dash, I am not sure if the pad is the problem or the dash.

So I have made it fit, it will be covered in leather so it should come out fine.

First I cut it up, then I filled it and shaped it with Sika Flex.

42739

42740

42741

42742

42743

42744

42745

My other big hate it the waviness on the leading edge of the dash pad as it's held down by about 8 clips. I had the boys at Rowe & Sons make me up a leading edge from metal, to hold it nice and straight.

42746

42747

[Greg from Aus]

42748

Now working on building out the area's around the A pillars, another terrible fit.

42749

42750

[DOOM]

Greg a lot of this aftermarket stuff is just garbage. That's a lot of work to make something fit but the end result will be perfect!:bow:

[GregWeld]

Sika Flex is bad ass stuff… always used the various "adhesions" on the boat. The strongest will rip fiberglass in two before it lets go.

Nice job mate!

[waynieZ]

Its looking good Greg.

[tubbed69]

nice work Greg,dashes do look bad

[Greg from Aus]

Greg a lot of this aftermarket stuff is just garbage. That's a lot of work to make something fit but the end result will be perfect!:bow:

Thanks Mario,

I have tried 2 of them, they both fitted the same. whats the old saying "do it once do it right".

Sika Flex is bad ass stuff… always used the various "adhesions" on the boat. The strongest will rip fiberglass in two before it lets go.

Nice job mate!

Thanks Greg, they sure do make some great products.

Its looking good Greg.

:thankyou:

nice work Greg,dashes do look bad

Thanks Jeff, It really does slow the process down, but looking over it everytime I drive it would drive me insane.

[tubbed69]

ok Greg were are the updates?its been a while now,are you making any progress?:poke:

[Sieg]

They're on the big ramp-up to Chrissy, I expect we'll get a report mid-January. :D

[waynieZ]

I'm waiting too.:relax:

[Greg from Aus]

ok Greg were are the updates?its been a while now,are you making any progress?:poke:

No none at all, still waiting on engine parts and I have been really busy with work.

They're on the big ramp-up to Chrissy, I expect we'll get a report mid-January. :D

Hey Sieg,

I hope everybody had a great Christmas and New Year.

I'm waiting too.:relax:

Sorry Wayne, the wait will continue until further notice lol.

[Sieg]

Glad to know you survived the holidays mate! :thumbsup:

[waynieZ]

Thats ok well worth the wait!

[LS7 Z/28]

The car is turning out awesome Greg good luck with the rest of it.

[Greg from Aus]

OK, the engine is alive.

The basics of it are:

RHS block.
Mast motor sport black label heads, Titanium valves, springs to suit.
Manley LS7 ultra light crank.
Manley ultra light H beam rods.
T&D rockers
Wiesco ceramic coated pistons with weight reduction.
Kaytech high flow oil pump.
OZMO twin throttle body carbon fiber manifold.
twin 92mm throttle bodies.
RHS piston squirter's.
Holley dominator ECU with LCD interface.

It has been built by Dave Crumes Race engines & tuned by Dave Hart Race engines. Dave Hart has used the OZMO manifold and the Dominator ECU before and has a good understanding of them.
It was run up today on Dave Harts swamp boat fan, and they put the horsepower at around 775. I was going to run it on the dyno as well, but decided to wait until it's in the car, here in OZ.

48593

48594

48595

48596

48597

--------------------------------------------------------------------------------

[Sieg]

Nice internal parts list ya have there Greg. :thumbsup:


If you'd like I'd be glad to make you a "Stick, You Hoon!!!!!!!" decal. :D

[Greg from Aus]

Hoon is a really bad thing here Seig, the media call everybody in a modified car a hoon and the cops go along with it.

[214Chevy]

Nice internal parts list ya have there Greg. :thumbsup:


If you'd like I'd be glad to make you a "Stick, You Hoon!!!!!!!" decal. :D

Hoon is a really bad thing here Seig, the media call everybody in a modified car a hoon and the cops go along with it.

:drive: :drive: :burnout: :burnout: >>>>>>>>> http://en.wikipedia.org/wiki/Hoon

[Sieg]

Hoon is a really bad thing here Seig, the media call everybody in a modified car a hoon and the cops go along with it.
Understood, a liberal dose of sarcasm was included in my generous offer. :D
Sounds somewhat similar to how the 'racist' card is played on this side of the pond. :(

How long before that motor makes it's way into the car?

[Greg from Aus]

:drive: :drive: :burnout: :burnout: >>>>>>>>> http://en.wikipedia.org/wiki/Hoon

Yep thats it, and yes it would apply to me :thumbsup:

[Ron in SoCal]

Awesome Greg! You win the prize for the most innovative test fire platform :D

:cheers:

[Greg from Aus]

Understood, a liberal dose of sarcasm was included in my generous offer. :D
Sounds somewhat similar to how the 'racist' card is played on this side of the pond. :(

How long before that motor makes it's way into the car?

We have that over here too, you aren't on your own there.

The ECU needs to go back to Holley for a software update and they have to build a crate to ship it, so hopefully a couple of weeks and it should be ready to go.

But I will be in the States for a month in September and early August, I am heading to Hot August Nights and another round at Bondurant. I will be home for a bit, then I'm heading to SEMA. :)

[Greg from Aus]

Awesome Greg! You win the prize for the most innovative test fire platform :D

:cheers:

Thanks buddy.

Hows that video going????????????

[GregWeld]

Hey Greg! I don't care what they call you in Australia... But I'm calling' ya "DA MAN!"


That engine is just way kool!

[Greg from Aus]

Hey Greg! I don't care what they call you in Australia... But I'm calling' ya "DA MAN!"


That engine is just way kool!

Cheers Greg,

I see you bailed on Hot August Nights :poke: , I was hoping to meet up, Now Ill just have Charlie.

[GregWeld]

Cheers Greg,

I see you bailed on Hot August Nights :poke: , I was hoping to meet up, Now Ill just have Charlie.




I went to HAN for years and years. My grandparents lived in Carson City - so it was always a good excuse to go visit them... and of course HAN "used to be" - the hot rod show in the country on the west coast... Then - frankly - it went to hell in a hand basket as far as I'm concerned. So I quit going about 5 years ago.

I get my fill of Charley at other events... I've thought - a nanosecond at least - about going back, but there's just other things to do - and I'm not any different than everyone else - I only have so many weeks to do "X" amount of car stuff - before it has to take a back seat to family stuff.

This year it is on the same weekend as the NorCal Shelby Mini Nats at Sonoma -- and I have more fun driving the car Charley gave away than I do sitting in a parking lot. (I've never been much of a car show guy).

I think you should modify your trip and include Sonoma for a couple hours... then have Charley send his helicopter to pick you up and whisk you over to Reno.

[Sieg]

I think you should modify your trip and include Sonoma for a couple hours... then have Charley send his helicopter to pick you up and whisk you over to Reno.
Best plan I've heard yet!

:thumbsup:

[LS7 Z/28]

Wow Greg the engine looks fantastic. I'm sure you'll have fun with that in the car! I'm definitely excited to see this project in the final stages...

then have Charley send his helicopter to pick you up and whisk you over to Reno.

USA Greg, sarcasm isn't easy to read through text on the internet. Does Charley really have a helicopter?

[GregWeld]

Wow Greg the engine looks fantastic. I'm sure you'll have fun with that in the car! I'm definitely excited to see this project in the final stages...



USA Greg, sarcasm isn't easy to read through text on the internet. Does Charley really have a helicopter?



SEVERAL -- and AIRPLANES TOO..... and about 100 cars, many of which are in various states. LOL


The man is a god.


I'll let him explain as I don't want to discuss his personal fleet of stuff.


But really... No, not that I'm aware of... but with Charley, you never know.

[Vince@Meanstreets]

gee greg, is that a chubby? lol


:D

[LS7 Z/28]

SEVERAL -- and AIRPLANES TOO..... and about 100 cars, many of which are in various states. LOL


The man is a god.


I'll let him explain as I don't want to discuss his personal fleet of stuff.


But really... No, not that I'm aware of... but with Charley, you never know.

Well that's disappointing... I can confirm he does have cars in various states though. I saw one of them hiding in Michigan a couple days ago. Cool stuff.

[tubbed69]

Greg that engine looks great,glad to see some updates:thumbsup:

[Al Moreno]

:G-Dub: :G-Dub: :hail: :cheering: :drool: :bow: :unibrow:

[Lenie]

OK, the engine is alive.

48594

--------------------------------------------------------------------------------

Oh my, I think that thing is smiling at me.:D Greg, that is awesome!

[Greg from Aus]

I went to HAN for years and years. My grandparents lived in Carson City - so it was always a good excuse to go visit them... and of course HAN "used to be" - the hot rod show in the country on the west coast... Then - frankly - it went to hell in a hand basket as far as I'm concerned. So I quit going about 5 years ago.

I get my fill of Charley at other events... I've thought - a nanosecond at least - about going back, but there's just other things to do - and I'm not any different than everyone else - I only have so many weeks to do "X" amount of car stuff - before it has to take a back seat to family stuff.

This year it is on the same weekend as the NorCal Shelby Mini Nats at Sonoma -- and I have more fun driving the car Charley gave away than I do sitting in a parking lot. (I've never been much of a car show guy).

I think you should modify your trip and include Sonoma for a couple hours... then have Charley send his helicopter to pick you up and whisk you over to Reno.

I planned the trip around HAN because Charlie said, It's not to be missed, he rated it above all other shows, so we will see.

It's a shame it's on at the same time as the Nor Cal deal as I would have love to be there for a look and add some banter.

I'm heading over to see Ron Sutton after Han on the Monday, as he is re valving some shocks for me.

Best plan I've heard yet!

:thumbsup:

And I thought you were the idea's man :headscratch:

Wow Greg the engine looks fantastic. I'm sure you'll have fun with that in the car! I'm definitely excited to see this project in the final stages...

Thanks Casey, I hope it will pick up some pace.


SEVERAL -- and AIRPLANES TOO..... and about 100 cars, many of which are in various states. LOL


The man is a god.


I'll let him explain as I don't want to discuss his personal fleet of stuff.


But really... No, not that I'm aware of... but with Charley, you never know.

Doesn't he just borrow your spare.:Tomcat:

gee greg, is that a chubby? lol

:D

Yep sure is Vince.

Greg that engine looks great,glad to see some updates:thumbsup:

Thanks Jeff.

:G-Dub: :G-Dub: :hail: :cheering: :drool: :bow: :unibrow:

:thankyou: Al, always look forward to your updates.

Oh my, I think that thing is smiling at me.:D Greg, that is awesome!

Cheers Lenie, I'm not sure about it smiling, but I am.

[GregWeld]

I planned the trip around HAN because Charlie said, It's not to be missed, he rated it above all other shows, so we will see.



Charley lives on a farm in the middle of nowhere... and really doesn't get out very much.

You'll have a good time. I think the show is getting it's second wind...





It's a shame it's on at the same time as the Nor Cal deal as I would have love to be there for a look and add some banter.



Ron Sutton will be with US.... not with Charley... and WE will be at Sonoma in the heart of beautiful wine country... and racin'... and Shelby's... CHARLEY will be in the middle of a hot asphalt parking lot in RENO in the 100* heat of a beat down old relic of a town that used to be kool when I was a kid - that was 50 years ago...



I'm heading over to see Ron Sutton after Han on the Monday, as he is re valving some shocks for me.




PER above... We know where he'll be on Saturday and Sunday.

[Greg from Aus]

Charley lives on a farm in the middle of nowhere... and really doesn't get out very much.

You'll have a good time. I think the show is getting it's second wind...

I hope so.


PER above... We know where he'll be on Saturday and Sunday.

Charlie, said only because your paying, otherwise he would rather hang with him.

[GregWeld]

Charlie, said only because your paying, otherwise he would rather hang with him.



Ron's just making me faster each weekend.... and I'll now have one more "seat time" session before Charley comes back to the track in October... :>)
He's old - he needs to just sit for the weekend and catch his breath.

[Ron in SoCal]

It's a shame it's on at the same time as the Nor Cal deal as I would have love to be there for a look and add some banter.

I'm heading over to see Ron Sutton after Han on the Monday, as he is re valving some shocks for me.



Greg just do it! Oh, good call on the shocks too :cheers:

[Greg from Aus]

Greg just do it! Oh, good call on the shocks too :cheers:

Yeah some guy put me onto him about the shocks, thanks mate.

Are you going to the Nor Cal track days?

[GregWeld]

Yeah some guy put me onto him about the shocks, thanks mate.

Are you going to the Nor Cal track days?




Yes he is Greg --- which probably influenced Charley's decision to go in the opposite direction.

[waynieZ]

Greg (AU ) Sweet looking motor and stout internals.
I knew this update would be worth the wait!

[Ron in SoCal]

Yeah some guy put me onto him about the shocks, thanks mate.

Are you going to the Nor Cal track days?

Yep I'll be there.

Yes he is Greg --- which probably influenced Charley's decision to go in the opposite direction.

Probably :lol:

[Sieg]

And I thought you were the idea's man :headscratch:
In this situation I was the motion man.

GW's idea was Sonoma and I wholeheartedly seconded the motion.

:thumbsup:

[WSSix]

Gorgeous engine, Greg. Glad it's alive.

[parsonsj]

Greg,

It's good to see you *finally* getting this thing up and running. Ty told me that he found the whole "bolt the engine to a massive propeller" bit both comical and a bit scary.

Now we need video!

[Greg from Aus]

Greg (AU ) Sweet looking motor and stout internals.
I knew this update would be worth the wait!

Thanks Wayne, it's been slow, but should move a bit faster now.

Yep I'll be there.

I might try to move things around and get over for the Sunday.


[QUOTE=Sieg;554840]In this situation I was the motion man.

GW's idea was Sonoma and I wholeheartedly seconded the motion.

:thumbsup:

Good work.

Gorgeous engine, Greg. Glad it's alive.

Thanks Trey.

Greg,

It's good to see you *finally* getting this thing up and running. Ty told me that he found the whole "bolt the engine to a massive propeller" bit both comical and a bit scary.

Now we need video!

Hey JP, Ty said the big blades where scary. He is going to send the video, when I get it ill post it up.

I will be in Orlando about the 20 -21 July would be great to catch up.

[Gambit]

I said it on usmuscle but it's worth saying again. That thing is wicked mate! Will look killer in the car.

Pity you're on the other side of the country. I'd love to check it out one day

[parsonsj]

I will be in Orlando about the 20 -21 July would be great to catch up.Sounds great!

[Greg from Aus]

I said it on usmuscle but it's worth saying again. That thing is wicked mate! Will look killer in the car.

Pity you're on the other side of the country. I'd love to check it out one day

Thanks again Nathan, It's not to far to fly.:poke:


Sounds great!

I will talk to you closer to the time :thumbsup:

[Flash68]

It was run up today on Dave Harts swamp boat fan

That is just stupid.

Stupid Awesome. :Tomcat:

[Greg from Aus]

That is just stupid.

Stupid Awesome. :Tomcat:

The Stupid part fits me pretty well. :thankyou:

[Greg from Aus]

As promised, a quick video of the engine being run up.


fugznO4nhBs

[Vince@Meanstreets]

WAHHHHH that is ******* terrifying. :thumbsup:

[Greg from Aus]

WAHHHHH that is ******* terrifying. :thumbsup:

Yeah pretty much, you wouldn't want to be near those blades.

[waynieZ]

Hell Yea! I was waiting for it to take off!!

[Greg from Aus]

Hell Yea! I was waiting for it to take off!!

Thanks Wayne, pretty scary hey.
Hows your beast coming along?

[Greg from Aus]

I thought I would post up Dave Hartz Race boat with a RHS motor.

U3FJR9v4SFQ

[Ron in SoCal]

Greg do they cam those boat motors differently than drag cars?

[Greg from Aus]

The engine is finally in my shed :ups: and the body is off at the painters getting the rest finished off, I hope the paint is finished when I get back from SEMA, then I can put it all together.


50626

50627

50628

Now I just have to remove the OZMO decals, as they don't fit my plans.

[GregWeld]

The engine is finally in my shed :ups: and the body is off at the painters getting the rest finished off, I hope the paint is finished when I get back from SEMA, then I can put it all together.


50626

50627

50628

Now I just have to remove the OZMO decals, as they don't fit my plans.



That's good news Greg! It'll be finished before they put me in the home. :D

[tubbed69]

The engine is finally in my shed :ups: and the body is off at the painters getting the rest finished off, I hope the paint is finished when I get back from SEMA, then I can put it all together.


50626

50627

50628

Now I just have to remove the OZMO decals, as they don't fit my plans.

Greg I bet you are getting excited now,that intake is awesome:trophy-1302: :trophy-1302:

[Flash68]

Wow. And I am sure it will run as good as it looks!

[tmadden]

Wow thats impressive

[LS7 Z/28]

Engine looks wild Greg. Should be some fun times ahead.