xssive99
08-21-2012, 06:28 PM
377" CI LME Forced Induction Shortblock - Ready for 1500HP
New 6.0L Iron Block direct from GM
* 4.030" Bore
* ARP Main Studs
* Durabond Cam Bearings
* 9.230" Deck height
* 9.0:1 Compression
Callies Magnum XL Crankshaft (2900$ new)
* Stroke 3.700"
* 2.000 Rod Journal Diameter
* LS1 Main Diameters
* Post Keyways
* No reluctor wheel
* Balanced to 1/4oz tolerance
* DART Oil Shedding Coating
GRP 1500 SERIES Aluminum Rods (1300$ new)
* 3/8 ARP 2000 bolt
* 6.125 Length
* DART Oil Shedding Coating
Wiseco Custom Piston (1100$ new)
* 4.030" x 1.250" x .927" x -17cc
* Coated Skirts
* Lateral Gas Ports
* Heavy Wall Tool Steel Wristpin Upgrade
* NPR GFX ring pack .047"/.047"/3mm
* .060" quench with .050" gasket
* .0045" Piston to Bore Clearnace
This is a new, never been fired shortblock!
All machine work was done by Bryan at LME in Houston. Ive attached the machining invoice and build sheet. Ive got over 8400$ into this shortblock as it stands. This not your everyday run of the mill mass produced shortblock. It was built to handle everything a PT-101 could throw at it, and make over 1500hp reliably.
Looking for serious buyers, not tire kickers...
6800$
http://i48.tinypic.com/250qlnd.jpg
http://i48.tinypic.com/20k39sw.jpg
http://i46.tinypic.com/210isqq.jpg
http://i45.tinypic.com/2chna6v.jpg
http://i49.tinypic.com/2nvco6g.jpg
http://i47.tinypic.com/28qsoiv.jpg
New 6.0L Iron Block direct from GM
* 4.030" Bore
* ARP Main Studs
* Durabond Cam Bearings
* 9.230" Deck height
* 9.0:1 Compression
Callies Magnum XL Crankshaft (2900$ new)
* Stroke 3.700"
* 2.000 Rod Journal Diameter
* LS1 Main Diameters
* Post Keyways
* No reluctor wheel
* Balanced to 1/4oz tolerance
* DART Oil Shedding Coating
GRP 1500 SERIES Aluminum Rods (1300$ new)
* 3/8 ARP 2000 bolt
* 6.125 Length
* DART Oil Shedding Coating
Wiseco Custom Piston (1100$ new)
* 4.030" x 1.250" x .927" x -17cc
* Coated Skirts
* Lateral Gas Ports
* Heavy Wall Tool Steel Wristpin Upgrade
* NPR GFX ring pack .047"/.047"/3mm
* .060" quench with .050" gasket
* .0045" Piston to Bore Clearnace
This is a new, never been fired shortblock!
All machine work was done by Bryan at LME in Houston. Ive attached the machining invoice and build sheet. Ive got over 8400$ into this shortblock as it stands. This not your everyday run of the mill mass produced shortblock. It was built to handle everything a PT-101 could throw at it, and make over 1500hp reliably.
Looking for serious buyers, not tire kickers...
6800$
http://i48.tinypic.com/250qlnd.jpg
http://i48.tinypic.com/20k39sw.jpg
http://i46.tinypic.com/210isqq.jpg
http://i45.tinypic.com/2chna6v.jpg
http://i49.tinypic.com/2nvco6g.jpg
http://i47.tinypic.com/28qsoiv.jpg