Brand New Art Morrison C5 weld in front clip

[TOURT]

Guys,

I have a brand new weld in 2x4 Morrison front clip. This is complete with all the C5 suspension pieces, sway bar, hubs, steering arms, power rack and strange coil overs.

This is set up for a 57 9/16" track width (hub to hub with rotors in place).

I have additional measurements if interested and can supply pics. This was purchased a couple of years ago for a project and never used.

Complete this sold for $5,180.00 (with all the suspension pieces etc). I would like to sell complete. Looking to get $4,500.00 (open to offers) feel free to PM or e-mail me at [email protected]

I might be able to deliver to a Goodguys event to save on freight.. just let me know where and when :)

Thx!
Rick

[Ron in SoCal]

That's a smokin' deal. If I didn't have one I'd be all over this....

[Rick D]

That's a smokin' deal. If I didn't have one I'd be all over this....

Ron I think this is different than your sub frame this is a weld up clip that Morrison sells. Still not a bad deal and i'm sure with some fab work it could be made to work in a camaro. Let's see some pictures please. If you need help posting them let me know and I can help.

[TOURT]

badrs69 (Rick)

I will take you up on that :) I will get some pics tonight and send them over to you.

Thx guys!
Rick

[TOURT]

Pics sent!!!

Thx again Rick!

Rick

[Rick D]

Here you go Rick! By the way nice piece wish I had the extra cash right now, I would pick this up for a project I have in mind next.

http://i79.photobucket.com/albums/j154/RS_427/Art%20Morrison%20Frame%20C6/tn_Picture488.jpg

http://i79.photobucket.com/albums/j154/RS_427/Art%20Morrison%20Frame%20C6/tn_Picture489.jpg

http://i79.photobucket.com/albums/j154/RS_427/Art%20Morrison%20Frame%20C6/tn_802.jpg

http://i79.photobucket.com/albums/j154/RS_427/Art%20Morrison%20Frame%20C6/tn_Picture204921.jpg

http://i79.photobucket.com/albums/j154/RS_427/Art%20Morrison%20Frame%20C6/tn_Picture493.jpg

[Ron in SoCal]

Ron I think this is different than your sub frame this is a weld up clip that Morrison sells. Still not a bad deal and i'm sure with some fab work it could be made to work in a camaro. Let's see some pictures please. If you need help posting them let me know and I can help.

Thanks Rick. You're right...as usual! :hail:

[TOURT]

Ttt :)

[MoparCar]

What is the outside to outside frame width and do you know how much offset vertically there is on the rails? How about how long the rear rails are? Sorry for all the questions--it would be for a Mopar application.

[TOURT]

The rails are 28 inches

As for vertical I have a tech sheet at home I can email a copy of or fax u... don't know off hand. The length is extra long so u can mold it into something. I can measure it for you and get back to you tonight. Thx!

[MoparCar]

Thanks that would be great. Not sure if it would work, but I'll get the tape measure and strings out to see!

Wes

[TOURT]

Wes,

Sending the e-mail now :)

Thx!
Rick

[TOURT]

still for sale :)

TTT

[SWAPMEETCRAZY]

still for sale :)

TTT

can u email the spec sheet on this also---may be what i'm looking for--jim

hotrodsoftexas @yahoo.com

[TOURT]

Jim,

Doing it now.. anything else needed let me know!
Thx
Rick

[TOURT]

Still up for sale guys!!

Need to sell :)

[HowieZo67]

What kind of car was this being built for?
Thanx Howie

[TOURT]

Howie,

I was building a frame for a Buick Grand National. I planned to use this, and a 9" with a 4 link out back.

Thx
Rick

[TOURT]

Still for sale!

I am flexible on the price (slightly :) )

I am sure someone can use this!

E-mail me for quicker response.

Thx guys!
Rick

[TOURT]

One last bump..

Then it is off to e-bay :)

I am sure someone could use this!!

[TOURT]

Back up for sale guys!!

Who needs a subframe??? :)

Thx

[samckitt]

:drool:

Man that would be nice, Grand National & Monte Carlo = same frame.

Will this work with stock sheetmetal body, or will front wheel position need to be changed, moved forward/back, wider.....?

If I only had $ to spare......

[The T-man]

this is gen1 Camaro I would guess?

[SWAPMEETCRAZY]

Buick :yes:

[TOURT]

I bought the clip to use as part of a frame build for a Buick GN. The track width is just slightly narrower than stock (from memory), but it would allow a 10" wide wheel up front. :)

The rails are narrow so it will require cutting some of the floor (depending on how you do it).

Can be used for any project where someone is planning to build a frame. I have had it awhile and dont plan to use it... so all you car builders someone buy this! :) LOL

This is not the bolt in Camaro subframe... this is a weld in piece.

Thx!

[TOURT]

anybody?? :)