Fesler needs parts so lets see what everyone wants

[fesler]

OK we started a new thread on our post to see what is hot, we are looking for more parts to make not that we dont have enough but we get a ton of emails all the time on parts to make.

Post up what you are looking for so we can start a list with priority on waht you guys want. The more parts request we get the faster we will make that part.

We also need stock parts, not remanufactured parts but stock OEM parts to build from. If you guys have parts and we dont already have them and you send them to us you will get the first set at cost. Let me know what you have and what you might be intersted in.

You must contact us before sending anything to us

thanks

[Rick Dorion]

Hi, Chris

Do you need 68 camaro standard rear tail light housing?

[tjbruning]

Chris, email sent (Cuda hinges).

[DRJDVM's '69]

Second on the Cuda hinges :).....more Mopar stuff....

Chris my offer still stands on using some of my Mopar stuff. Just give me and TJ a list and I'll see what we can do.

Ned
209-825-5579

[HRBS]

Make that 3 for Cuda hinges..... we've got one coming in soon.

[fesler]

We have the cuda hinge what we need is all the other parts on the car to make, like the trunk hinge, tail lights, marker lights and any other part you guys want to see. We are working on the Hood Hinge for you guys and should have something soon

[paulk68]

Hi, Chris

Do you need 68 camaro standard rear tail light housing?


anything on these

[slownova]

some 68 firebird parts.

[youthpastor]

these would look awesome - a little lower profile than the factory ones...to go with my hinges:D

[3_z28camaro]

Billet 1970-1973 Camaro RS turn signals.

I also sent you a PM a few days ago about 1969 Firebird tail lights, Chris.

[olds87]

I got a 87 Olds Cutlass, if you want to barrow to build some parts.
I'm not that far from you, but the engine is shoot though.

[SWAPMEETCRAZY]

Chris--let me throw out this bone--I know u have some of this ugly laying around--upper and lower latch assemblies on the 67-72 C10's--Possible???
Don't know how billet would hold up or work in the latching operation--BUT DAMN THERE UGLY!!! LOL JIM (ORDERING HINGES SOON):hail:

[zcrz]

what about 69 camaro rocker trim?:cool:

[bigtyme1]

pm sent

[bigtyme1]

what about 69 camaro rocker trim?:cool:

I second that as well. Also Sill plates for 69 Camaro.

[662drsdn]

66-67 chevy II/Nova tail lights!

[Mr.VENGEANCE]

67 camaro taillights

69 gto taillights

:_paranoid

[CRCRFT78]

63 Nova taillights bezels
63 Nova SS dash trim & knobs
63 Nova parking lights bezels
63 Nova hood & trunk hinges

Pretty much anything for the 1st generation Novas

[Cread01]

2nd gen camaro's are getting more and more popular. I would like to see a replacement cowl screen, kinda like your door jamb vents. you had said in another thread that you are working on door sills, that would be cool also.

This isn't billet but It would be nice to see a cool close off plate made that covers the spot in front of the radiator support for second gen's also. maby something that folow's the contours of the hood latch but with something extra to make it look cool. There are other products like this out there but they are just a flat sheet.

[fesler]

Hi, Chris

Do you need 68 camaro standard rear tail light housing?


Yes if you have a good stock set I would love to see them for a few weeks. let me know. They have to be stock OEM not aftermarket

[fesler]

these would look awesome - a little lower profile than the factory ones...to go with my hinges:D

Do you have the stock one to send us?

[Rick Dorion]

Yes if you have a good stock set I would love to see them for a few weeks. let me know. They have to be stock OEM not aftermarket
Chris, how good do they have to be? These are original but a little 'bumpy' from the traditional pitting. If these would help I'd be glad to send them to you.

[Orng Crsh]

2nd gen camaro's are getting more and more popular. I would like to see a replacement cowl screen, kinda like your door jamb vents. you had said in another thread that you are working on door sills, that would be cool also.

This isn't billet but It would be nice to see a cool close off plate made that covers the spot in front of the radiator support for second gen's also. maby something that folow's the contours of the hood latch but with something extra to make it look cool. There are other products like this out there but they are just a flat sheet.

X2 - The flimsy plastic factory cowl screen is one of the ugliest parts on a second gen.

[QUICK6]

How about some tail lights for the 75-79 nova.I have a set I could send out?

[tony byram]

Agreed the cheap plastic cowl screen is crappy, a billet screen would be great and the cover ahead of the radiator, between the header and radiator is a GREAT idea! Check out the one that Kyle Tucker owner of Detroit Speed and Eng. built for his blue 1970 test Camaro, some thing along those lines would be great! It may even fit second gen Firebirds as well! It would serve to direct air flow into the radiator as well as make that area look ALOT better. Billet alum door inserts are a thought too... Hope you make some of these Chris, You guys make some beautiful stuff as well as Beautiful cars. Love that bad and black 69 that you guys built! The finish was just outstanding! Tony:thumbsup:

[ItDoRun]

PM Sent. I hope I didn't overload you with ideas.

[slammed con]

:hail: i was thinking about billet gills for the 69 i think that would be sweet:faint:

[jy211]

how about flush mount tail lights for first gen's?

[Gordz32]

-Just an Idea but how about some real brake duct trim pcs for 69 camaro quarters.

[Radlark]

NOBODY makes anything for these cars and I would like to see anything like a custom dash, billet ac vents, ANYTHING........I know its a long shot! Preferably 1969 Impala's

[BBC69Camaro]

Billet ram/cold air induction box/kit, especially something to pull in cold air from a cowl hood as well as from the fenders.

[redfire69]

:hail: i was thinking about billet gills for the 69 i think that would be sweet:faint:

X2! I was looking into having these made like the OEM version, so these would be awesome! Door handles as well as previously mentioned, that fit the stock mounting points. Thanks-

[zoomiefoosh]

How about some billet '69 Camaro RS reverse lights?

[fesler]

Lots of good stuff here, we are working on some of this now and will have it out very soon, some good new ideas here and what I might do is figure out a way to creat a poll on some of this stuff so I can see how many people want stuff. I have to have numbers to creat most of it.

Keep the ideas coming and we will figure them out as we can. We just ordered another machine so we will have 3 in house machines building parts with 2 shifts running.

This will cut down on any BO stuff huge even though most of our BO is only 7 days at most.

[Perry Mitchell]

Chris, has anyone requested turn signals/park lights for the 67 Camaro with standard grill yet?

[jy211]

tow hook/tie down hook of some sort :D

[Weldon0405]

X2 on the door handles.

[brans72]

chevelle parts :yes:

[DFRESH]

Chris, how about the passenger OMG grab handle and the huge plastic piece behind it just above the glove box door on 69's--not sure if this was an option on 7's or 8's. The plastic plate behind it that runs along the length of the dash could be done in carbon fiber with a beveled edge, with a brushed billit "Camaro" emblem or just reuse the stock one---then the handle could be done in maybe a round stock aluminum--also brushed. You could do many combos. I've started it in the drag car (used an aluminum piece behind the handle and polished it), but would love to see someone with skills do it and offer combos for it. I'd love to see the carbon fiber look. If you would like pics of my job on the race car, let me know--but I think you get the idea--seems like it would be fairly easy to do and have lots of different combinations. I'd purchase from you right away for the new pro touring project I have going. It was great to meet you at SEMA.

Doug

[68LS1]

How about a set of exterior mirrors?
Sympathetic to 68/69 square style with modern touch. Housing with mirror mounted internally. I'm very much in to that stock look with modern functionality. The originals I have found tend to be hard to see out of at speed due to wind buffeting and come loose over time.
Could also do a version with 3/4 "cap" in carbon fibre or painted for those want a more modern look.
This is now really only 1 of 2 items I can't seem to find something I really like (dash gauges are other) for my 68 convertible. I feel like I've looked at everything suitable I can think of over the last 5 odd years, but feel either too "pointy" (2nd gen sports) or the modern ones are too curvy with a bulky base.
I notice the Fesler, Foose & Ring Brother Camaros do not have exterior mirrors.
I can live with out remote adjustment as I'm the only one that will drive it :yes:
If anyone knows of mirrors that may fit what I'm looking for please chime in.

[Flash68]

Can someone (Fesler?) please build a nice legit dash/gauge insert for the 67-68 Camaro/Firebird?? I almost wish I had a 69 so I could get the DSE piece! :willy:

[68LS1]

Can someone (Fesler?) please build a nice legit dash/gauge insert for the 67-68 Camaro/Firebird?? I almost wish I had a 69 so I could get the DSE piece! :willy:

x 2, original looking, to hold 4" - 5" speedo & tach, inbuilt high beam signal & indicator flashes, please

[fesler]

I am working on building all the dash parts now and am looking into metal and carbon fiber to get the price down where you guys will buy them. We will have a dash kit for a ton of the cars listed here very soon

[Cread01]

kinda off topic but do you know when the billet trunk hinges for second gen camaro's will be available?

[Flash68]

I am working on building all the dash parts now and am looking into metal and carbon fiber to get the price down where you guys will buy them. We will have a dash kit for a ton of the cars listed here very soon

Very cool. Looking forward to that Chris!

For all of us 67-68 guys out there I would think this would be a very good product to sell as an alternative to the Covans pieces.

[ItDoRun]

Very cool. Looking forward to that Chris!

For all of us 67-68 guys out there I would think this would be a very good product to sell as an alternative to the Covans pieces.

I agree! :thumbsup:

[Weldon0405]

I am working on building all the dash parts now and am looking into metal and carbon fiber to get the price down where you guys will buy them. We will have a dash kit for a ton of the cars listed here very soon

This is very exciting! I can't wait to see these dash kits! :woot:

[Pro Rides]

How about taillights for a 72 Chevelle.

[Vegas69]

Very cool. Looking forward to that Chris!

For all of us 67-68 guys out there I would think this would be a very good product to sell as an alternative to the Covans pieces.

Anvil makes one now.

[Flash68]

Anvil makes one now.

True, but I want something that isn't just the stock original piece made out of carbon fiber. Something nice and custom like the DSE piece for 69s. :)

I do like the stock dual-tunnel panel but just redoing it exactly the same shape in a different material isn't too special in my opinion.

[Craig67]

Since nobody makes a re-pop, how about a nice center A/C vent for a 1967 Chevelle.

[Radlark]

I am working on building all the dash parts now and am looking into metal and carbon fiber to get the price down where you guys will buy them. We will have a dash kit for a ton of the cars listed here very soon

Please have one of them be for a 1969 impala or better yet build me a one!:lol:

[ANVIL1]

True, but I want something that isn't just the stock original piece made out of carbon fiber. Something nice and custom like the DSE piece for 69s. :)

I do like the stock dual-tunnel panel but just redoing it exactly the same shape in a different material isn't too special in my opinion.

Don't mean to Hijack your thread, Chris, but I feel compelled to reply. Our 67/68 instrument panel looks like we just copied the original and made a carbon fiber version of it, but a lot of work went into making the openings larger so the aftermarket gauges would actually fit. You can jam gauges into a stock panel, but they get stuck before they totally bottom out into the recess. I do, however agree that a substitute panel that would fit more than two gauges would be great. Chris, let's work on this together and git 'er done!

[Flash68]

Don't mean to Hijack your thread, Chris, but I feel compelled to reply. Our 67/68 instrument panel looks like we just copied the original and made a carbon fiber version of it, but a lot of work went into making the openings larger so the aftermarket gauges would actually fit. You can jam gauges into a stock panel, but they get stuck before they totally bottom out into the recess. I do, however agree that a substitute panel that would fit more than two gauges would be great. Chris, let's work on this together and git 'er done!

Matt, my intent was not to badmouth your piece. It is a nice piece for sure. I was just looking for something different, as you said, specifically for a panle that would fit 6 or 7 gauges total like the DSE 69 piece. I should have chosen my words a little more carefully. My apologies for that.

BTW, I prefer when the 5" aftermarket gauges are inserted from the rear on the stock 67-68 panel. The fit is much better IMO. :)

[JETSET700]

I am looking for a 67' 68' dash insert to install a racepack into. The dual
layout of the panels out there make it difficult.

Peter

[ANVIL1]

Matt, my intent was not to badmouth your piece. It is a nice piece for sure. I was just looking for something different, as you said, specifically for a panle that would fit 6 or 7 gauges total like the DSE 69 piece. I should have chosen my words a little more carefully. My apologies for that.

BTW, I prefer when the 5" aftermarket gauges are inserted from the rear on the stock 67-68 panel. The fit is much better IMO. :)

No worries, Gordon. I just wanted to set the record straight about our part.

[catmull]

dash for 67-68 camaro

[Flash68]

dash for 67-68 camaro

WORD! :D

[68/Camaro]

67-68 Billet Side marker lights
67 68 69 camaro Billet door sill plates

[3_z28camaro]

How about some billet aluminum 1969 Camaro rear quarter louvers that have a mesh/grill insert that mimics brake cooling ducts?

[DFRESH]

How about some billet aluminum 1969 Camaro rear quarter louvers that have a mesh/grill insert that mimics brake cooling ducts?

X 10.:thumbsup:

[dylanCamaro582]

'70-73 firebird tialights, turn signal bezels, side makers.

[TreySmith]

ANYTHING for a 70 GTO!!! That is the reason you don't see many of them. NO PARTS!! Lol...

[The WidowMaker]

headlight bezels for 70 chevelles, if it hasnt been said already.

[1badchevelle]

WE talked this weekend the the Grand National. I was looking for the 71 chevelle taillights with led sequential if possible. Pm me what you need to make it happen and how much will it run me.

[Blitzwing]

Hope I'm not too late on this.

I'll second the 70-73 LED Firebird Tail lights, marker lights.

And for those who run door handles still......How about some standard GM exterior hanles, like the 2nd Gen Fbody ones for example, in aluminum? Tons of applications for those and they would look excellent.

[2Bad4Ya]

1st gen camaro dash center trim. The piece that is either black or wood grain trimmed in chrome that goes over the ac/heater, radio, ash tray section.

Make it with brushed aluminum or black anodized center area and polished outer lip. Make some with no openings and make some with cutouts in place.

[amargari]

X2 on the door handles.

Another vote for exterior door handles for the 2nd gen.

[ebncrdr]

How about door jamb vents for 68-72 Novas???

[D Rock]

1st gen camaro dash center trim. The piece that is either black or wood grain trimmed in chrome that goes over the ac/heater, radio, ash tray section.

Make it with brushed aluminum or black anodized center area and polished outer lip. Make some with no openings and make some with cutouts in place.

I agree, the 67 and 68s don't have many good choices for that center dash piece. I would buy something if it had a good place for a stereo and maybe a few gauges.

[f1shman]

I agree, the 67 and 68s don't have many good choices for that center dash piece. I would buy something if it had a good place for a stereo and maybe a few gauges.

A quality center dash piece would be something that I would be interested in buying, especially if it had gauge space AND spot for a modern radio head unit. I also have to put my stamp of approval on door handles. I know it was posted before that they are in development, but I have yet to see anything else on them.

These probably wouldn't be a fabricated part on your end, but I would love to see you guys carry an aftermarket headlight kit for the 5-3/4" light crowd. You only seem to offer 5" and 7" units at the moment.

[joe440]

a body mopar stuff. there is nothing for us, cudas and challengers have a lot more offered already. but no one is really making cool billet stuff (like you guys do for camaros and such) for a bodies. some 68' dart hood hinges would be killer, also some rear tail light bezels,i think would sell like crazy. if interested in making any a body mopar stuff a great place for suggestions is www.forabodiesonly.com, im sure they'd be more than glad to give you some ideas.:cheers:

[bulldog19]

Chris anything new on the 1st gen exterior door handles?
Thanks
John

[BonzoHansen]

I bet a lot of 2nd gen guys would like an auto shift plate in billet.

http://www.classiccarrestorationparts.com/catalog/14015852_r.jpg

[SS454]

How bout the rubber piece on the rear bumper of a 70 Chevelle that has the SS emblem embedded in it. Make it out of Aluminum, anodize it black then remachine the SS emblem and on the other side machine the engine size with horsepower rating. Could even machine the name of the car, possibilities are endless. Of course you have to have a machining center with enough travel for the length of the part. Just buy a bigger machining center, just think of the number of parts you can put on the table at one time, cutting down on machine time, and cost, per part.

[wookham]

here's what i want

1971 rs camaro

hood hinges
hood stops
cross braces
rs lights
side marker lights rear taillights
rear marker lights
door vents
strikers
and anything else you all makes

also would like a 1-piece headliner do you do that,,,i'll cover it in suede

[lil427z]

70-73 rs ft turn signal camaro:lateral:
thanks rick k

[andrewmp6]

How about maybe some ford parts or late 2nd gen fire bird parts?Or even 73-87 chevy truck parts.

[syborg tt]

Chris - looking for a set of billet hood hinges for the 57

[fesler]

Chris - looking for a set of billet hood hinges for the 57

Soon we are working on them now, they have been a pain but we are getting close. I will post pics up soon

[fesler]

We already have the hood hinges, Hood adj, door vents, strikers and tail lights. We are working on the cross braces and lights now

here's what i want

1971 rs camaro

hood hinges
hood stops
cross braces
rs lights
side marker lights rear taillights
rear marker lights
door vents
strikers
and anything else you all makes

also would like a 1-piece headliner do you do that,,,i'll cover it in suede

[fesler]

Door handles will be out anytime, we are almost finished with them. I will look into the headlights and see what I can find.

A quality center dash piece would be something that I would be interested in buying, especially if it had gauge space AND spot for a modern radio head unit. I also have to put my stamp of approval on door handles. I know it was posted before that they are in development, but I have yet to see anything else on them.

These probably wouldn't be a fabricated part on your end, but I would love to see you guys carry an aftermarket headlight kit for the 5-3/4" light crowd. You only seem to offer 5" and 7" units at the moment.

[fesler]

How about door jamb vents for 68-72 Novas???

can you send me your door jam vents?

[syborg tt]

Soon we are working on them now, they have been a pain but we are getting close. I will post pics up soon

Thank you but you need to hurry up - we need them for the 57

They sure would finish off the engine bay.

http://garagescene.net/gallery2/d/6199-5/2008+09-20+GG+Joliet+004.JPG


http://garagescene.net/gallery2/d/6201-3/2008+09-20+GG+Joliet+005.JPG

[sacarguy]

its been said before.


BILLET 69 GILLS

[70rs]

Chris, Do you need anything off a 1970 Camaro rs? I have a complete car and would be happy to contribute to your parts development even though I am just about to start mine and have no idea what I might want for it in the future. Anything on my car that might help? I noticed above someone had quite a list for 2nd gen parts and another wanted rs parking lights. Let me know what you need.
Eric:thumbsup:

[Teamwild]

Here's a weird one I haven't been able to find. I just bought some Corvette C5 seats for my '67 camaro off Ebay and when they came both seat back releases were broken off. They're small levers that are mounted in the back of the head rest. Very thin and fragile looking, and I haven't been able to find a replacement. Some Billet ones would be sweet but no one seems to have them. Should think the Corvette comunity would be all over that one...


Matt

[markss28]

How about some billet hood pins or at least the disk that hold it down?

[syborg tt]

How about some billet hood pins or at least the disk that hold it down?


uhm - hoodpins.com or hoodpins.net ??

[HRBS]

Chris... After researching a bit, I sent you some info via PM that I thought would be great for you. It seems that a certain hinge you ALREADY make may be applicable in other applications and I offered to verify one of those fitments on a car we have here now. After no response from you, I see you now list a few of the applications I PM'd you on your site. So I guess you're not interested in my offer of verifying these applications ? :cool:

[fesler]

I sent you a PM back

Chris... After researching a bit, I sent you some info via PM that I thought would be great for you. It seems that a certain hinge you ALREADY make may be applicable in other applications and I offered to verify one of those fitments on a car we have here now. After no response from you, I see you now list a few of the applications I PM'd you on your site. So I guess you're not interested in my offer of verifying these applications ? :cool:

[HRBS]

Hey Chris.... I never got it. My inbox is still empty.
PM me or feel free to give me a call tomorrow.
Thanx !

[Danny Thomas]

I agree, the 67 and 68s don't have many good choices for that center dash piece. I would buy something if it had a good place for a stereo and maybe a few gauges.

I second this.. build something that would help with stereo install especially new cd versions and would address the angle issue. Adding gauges would also be awesome. Something like DSE did with Dale Jr's 1st gen.

[John510]

How about a dash like the Marquez one?

[fesler]

How about a dash like the Marquez one?

Why? he has them and is shipping them isnt he?

[redfire69]

its been said before.


BILLET 69 GILLS


I would be interested in these as well...:thumbsup:

[texas56]

47 to 55 Chevy truck hood hinges

[fesler]

I will have pics posted of the first prototype for you guys in the morning on the following.

MOST GM Billet door handles

69 Camaro RS back up lights

69 Camaro driving lights

We will also have these out at Del mar if you want to come by and check them out.

[fesler]

I would be interested in these as well...:thumbsup:

These should be ready soon, we are on them

[redfire69]

These should be ready soon, we are on them

Chris, that is KILLER! You guys rock!

[fesler]

We did a new post in the Fesler form for the new driving lights, door handles and back up lights. Go check them out.

[Hemi Nova]

68-69 Nova side marker lights?
70 and up Nova side marker lights?

[TreySmith]

79-81 Trans Am parts? :D

[ebncrdr]

68-69 Nova side marker lights?
70 and up Nova side marker lights?

x2!:thumbsup:

[Ron Fox]

Hi Chris,

I would like to see billet grills and billet Finder Ornaments for the 1969 Firebirds. Are these parts possible in the near future?

Thanks.

Ron
1969 Firebird, 4-speed Coupe

[cfwjr1974]

I need a set of billet hood hinges for a 1962 Chevrolet Bel-Air 2-door post car.

Let me know....

Chuck

[D Rock]

tow hooks?

[PASD U]

chevelle parts :yes:


EARLY Chevelle parts. You know...64's, 65's.

Gauge bezel
Glove box inlay (that'd be fairly easy)
Mirrors
Side trim
Tail panel trim

[T-Type]

i had asked in the old fesler section about the flush racing style fuel cap with a flip top.......just wondering if you'll be making something like that? any plans for it? anything close to it?

[fesler]

EARLY Chevelle parts. You know...64's, 65's.

Gauge bezel
Glove box inlay (that'd be fairly easy)
Mirrors
Side trim
Tail panel trim

funny you should ask we have the hood hinge, door striker and hood adj right now and will have the hood latch and trunk hinges very very soon. Check back and you will be able to buy everything at once

[1970cuda]

what e body parts do you have in the works?

[PASD U]

I saw the majority of the parts you mentioned. I just want to have MORE parts offered than those Camaro guys. They get all the toys.:mad:

[fesler]

what e body parts do you have in the works?

We have Hood hinges, trunk hinges, hood adj, door strikers and tail lights for the 70-72 CUDA. Looking into door handles right now as well