Intro Twisted Vistas, 20x8, Nitto Invos

[Kenny_Cox]

I am new to the site, but figured I would give it a shot. I can give tons of feedback ratings from other forums, as well as over 100 positive feedback on ebay. I am selling the wheels because I have decided to go a different route all together with my build. After speaking with Rushforth, I think that's the way I want to go as they will fit the theme better. The wheels are in pristine condition but they have been mounted on the tires, therefore I cannot consider them "brand new". They have NEVER been driven on, never seen weather, never been "used". It's a set of 20x8 inch twisted vistas, one of my favorite wheels that Intro makes. The backspacing on all four wheels is 4 3/4 inches.

The tires are the new nitto invo tires, fronts have a set of 245/35/20's and the rears, 255/35/20. I understand that some might want a wider set for the back, but I will still attempt to sell them here.

I am asking $2600 for the wheels and tires, or $2000 without. Shipping will be covered half and half. I pay half, you pay half:willy: . If you have any questions at all please email/pm me I will answer them promptly. :woot:

http://i16.photobucket.com/albums/b42/tukn18s/SL370658.jpg
http://i16.photobucket.com/albums/b42/tukn18s/SL370660.jpg
http://i16.photobucket.com/albums/b42/tukn18s/DSC00767.jpg

Please note: I am willing to take any reasonable offers at this point in time!

[SWAPMEETCRAZY]

KENNY--THAT IS A 5 ON 4 3/4 PATTERN??? BEAUTIIFUL WHEEL!! NEED MORE PICS WHEN U GET NEW WHEELS !! WE LIKE ALL PROJECTS WITH A "HANDS ON" OWNER!!:unibrow: :unibrow: JIM

[awr68]

SOAB Kenny! Don't those frames hang down a lot further than that? What did you cut the floor out of it too? That's a killer ride right there! Oh, and best of luck with the sale!! :thumbsup:

[Kenny_Cox]

They are 5x4.75, with 4.75" of backspace. I am uncertain to what the backspace setup on a G-machine might be, but I know most bolt patterns would match up. Seems like the other set of Intros that sold were the same setup!:thumbsup: I have big plans for the blazer build from here on out, just need to sell these wheels to free up a little money. The frame is completely rebuilt from the firewall back with 2x3" tubing. The floor is stock for the most part, except for the tubs in the back.:lol:

[Kenny_Cox]

I am more than willing to split, as I have a buyer lined up for just the wheels over on another forum. I wanted to see if I could sell them as a unit instead of getting them dismounted but obviously no interest:(

[Kenny_Cox]

For both, right now, I am willing to take 2300. I need to get saving to purchase my Rushforths and I need to spend some money in different parts of the build!:yes:

[Kenny_Cox]

Is it the price? wrong backspacing? Just a little input. I will stop bumping once I know what the problem is :)

[dhutton]

Is it the price? wrong backspacing? Just a little input. I will stop bumping once I know what the problem is :)

Those sizes don't work well on first gen Camaros which is the most popular car on this site. Most guys want a 9.5 or 10 inch wheel for the rear, bigger if it is minitubbed. 20's are not very popular either and might be tough on the front.

Just my two cents worth,

Don

[Kenny_Cox]

Hey no big deal. Figured somebody might want to step out of the norm. The 8 inch wide wheel I understand the lower level of interest, but, I still wanted to try.

[Lotaimpalass]

These are one of the best looking wheels on the market today and are the correct size for my car. But I just picked up a new rolling chasie, 6.0l 4l80E combo this week and money is now way to tight. If it were a few months later I would be all over it.

Good luck.
Matt

[Kenny_Cox]

nice combo on that chassis you got there, I would kill to have that to put in my blazer project (not literally:willy: ) thanks for the luck. i am going to try to sell off the entire project. I am tired of it.